• 한국정보통신학회논문지
• /
• 제9권7호
• /
• pp.1601-1606
• /
• 2005

본 연구에서는 자동차가 정지하면 지정된 수초이내에 자동차의 공회전 상태를 자동적으로 정지시키고, 운전자가 출발하고자 할 때는 약속된 전기신호로 엔진의 시동을 거는 차량용 공회전 자동정지 제어시스템을 개발하였다. 이 장치는 다수의 선별된 엔진제어유닛과 변속기제어유닛의 전기신호를 입력신호로 하는 마이크로프로세서와 기타 주변 전자회로로 구성되어 있으며 자동차의 운전상태를 인식할 뿐 아니라 냉각수 온도에 따라 그 작동을 조정하고 재시동시 연료분사스킵 기법을 적용하여 자동차의 연료절약 및 유해배출가스를 저감하는 효과를 가지고 있다. 국내의 자동차 연비 및 유해배출가스측정 공인기관에서 ECE15+EUDC모드에서 본 제어시스템 장착차량의 주행시험을 실시하여 그 효과를 확인하였고 실차 적용가능성을 확보하였다.

• 설비공학논문집
• /
• 제2권3호
• /
• pp.166-176
• /
• 1990

Experimental study was made to find the effective ways for cooling of engine room in a power car through natural ventilation, forced ventilation and wind tunnel test of 1:10 model. Through the measurements of inner temperature of engine room and pressure distribution of model surface for the various opening combinations and the fan locations, the following results are obtained. For natural ventilation, side and top opening combination is more effective than the side openings only and optimal opening combination is all side openings with top center opening. For forced ventilation with fan on the roof, the combination of all sides and top opening is more effective than the combination of side and top opening, and the optimal location of fan is top center. When the model is located in the air stream, the combination of side and top opening is more effective than the side openings only, and the optimal location of top opening is the front opening. With both air stream and forced ventilation, the optimal location of fan is the side region, and the direction of side grill installation is found to have negligible effect on the room ventilation.

• 한국자동차공학회논문집
• /
• 제9권2호
• /
• pp.35-42
• /
• 2001

The diesel engine exhaust gas is know as one of the causes to produce photochemical smog, which causes damage on environmental. However, due to the high thermal efficiency and low carbon dioxide emission, the usage of a diesel engine is prevailed. In this study, the DC non-thermal plasma technology used to the particulate matter (PM) aftertreatment. The exhaust gas characteristics and energy density were investigated on the dynamometer test bed and chassis dynamometer with CVS-75 mode in a passenger diesel car. It was reported that the smoke removal efficiency has around the 70% in the dynamometer test with 80W energy consumption and the PM removal efficiency has the 68% in the real car test. The NOx also reduced the 20% according to electrode type respectively. Considering these results, plasma technology is one of the ways to simultaneously removing method the particulate matter (PM) and NOx.

• 한국자동차공학회논문집
• /
• 제22권5호
• /
• pp.102-107
• /
• 2014

Because of high oil prices and emission gas problems, many governments tighten regulation of fuel economy and emission gas. For Passenger car, there are many researches for plug-in hybrid electric vehicles and they are being manufactured. On the other hand, there are few researches for plug-in hybrid electric bus that is heavy commercial vehicle. In this study, analysis of fuel economy for series plug-in hybrid electric bus according to engine operation strategy based on simulation is conducted. Forward simulator is developed using Autonomie. Engine operation strategies consist on constant engine operation strategy and engine on/off operation strategy. Considering the engine operation strategy, results of vehicle speed, engine operating points and fuel economy are obtained and analyzed. As a result, engine on/off operation strategy has more advantage than constant engine operation strategy in terms of fuel economy.

• 오토저널
• /
• 제5권2호
• /
• pp.15-20
• /
• 1983

The nature and the sources of sound in cars is discussed in the light of many previous works, and the importance of the system resonances inside cars is suggested. An investigation of a 'boom' problem in a small size passenger car is described. It was established that the 'boom' frequencies coincided with engine firing frequency and also with several system resonances. To find out main transmission path of the noise to the car interior, various possible sources were eliminated from the investigation by means of simple modification to the vehicle. Data on the structural modes of the body, and the acoustic modes of the passenger compartment at various forcing cases were obtained to provide better understanding of the problem. It was found that the acoustic resonance responsible for the boom was controlled largely the bending motion of the floor. To investigate the effect of the structural modification to the acoustic response, center floor of the car was reinforced. a great reduction of the noise inside the car especially at the offending speed range, was achieved by this modification.

• 대한인간공학회지
• /
• 제29권6호
• /
• pp.959-964
• /
• 2010

Seat belt is an important means to protect drivers and passengers from the damages by car accidents. Many ways to increase the seat belt wearing rate have been proposed through human factors researches. The primary ways to increase seat belt use rate have emphasized the intention-behavior cycle. This study focused on the gap between intention and behavior. The gap may be bridged by the habit for seat belt use behavior. Divers following a desirable car starting sequence, from sitting on the chair, fastening seat belt, starting engine to moving a car, reported that higher belt wearing rate and unconscious behavior (automated response). That is, the habitualized procedure knowledge prevented drivers from forgetting to fasten their seat belt. The reminder systems such as warning light and warning sound could not significantly give an influence in remembering to fasten seat belt. In order to increase the seat belt use rate, the desirable car starting procedure should be included in the driving education program.

• 한국자동차공학회논문집
• /
• 제10권1호
• /
• pp.99-105
• /
• 2002

About 70% of energy input to internal combustion engine is rejected to atmosphere by heat. By utilizing this waste heat, a plenty of energy can be conserved in nationwide. One of possible ways is the thermoelectric generation to utilize engine's waste heat to provide auxiliary electric power. Under th is concept, we have been developing the thermoelectric generation system to replace the alternator by converting the waste heat in the engine's exhaust directly to electricity This system may reduce the shaft horse power of the engine, then improves the vehicle fuel economy and the exhaust emissions. In the present study, the characteristics of the electric energy and exhaust heal energy in city and highway mode driving conditions are analysed by using a gasoline passenger car. These results would be used to determine the optimum design parameters of the thermoelectric generation system.

• KSTLE International Journal
• /
• 제3권1호
• /
• pp.26-29
• /
• 2002

The International Lubricant Standardization and Approval Committee (ILSAC) GF-3 passenger car engine oil specification has been introduced commercially in July 2001. The new specification oil provides superior performance in terms of fuel economy, control of high temperature deposits, and oil consumption. These enhanced performances of GF-3 engine oil need high quality base oil as well as a better additive system. In this paper, the effect of base oil on various performances of ILSAC GF-3 engine oil was investigated. From the GF-3 sequence engine tests, Group III base oil shows better performance in fuel economy retention, oxidation and varnish control than combination of group III and group II or group III and group 1.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.571-575
• /
• 2008

An engine cradle is a quite important structural assembly for supporting the engine, suspension and steering parts of vehicle and absorbing the vibrations during the drive and the shock in the car crash. Recently, the engine cradle having structural stiffness enough to support the surrounding parts and absorbing the shock of collision has been widely used. The hydroforming technology may cause many advantages to automotive applications in terms of better structural integrity of parts, reduction of production cost, weight reduction, material saving, reduction in the number of joining processes and improvement of reliability. We focus on increasing the durability and the dynamic performance of engine cradle. For realizing this objective, several optimization design techniques such as shape, size, and topology optimization are performed. This optimization scheme based on the sensitivity can provide distinguished performance improvement in using hydroforming.

• 한국자동차공학회논문집
• /
• 제1권3호
• /
• pp.46-54
• /
• 1993

In order to develop a fuel-efficient gasoline engine oil, an experimental study was conducted using an engine dynamometer, a passenger car and the SRV machine. Oil samples with different viscosity were prepared by adding several friction modifiers to select the best one and also to investigate the effect of the viscosity grade. From the study, we have developed engine oils which result in good fuel economy. The viscosity grade of 7.5W/30 was best among the oils investigated with respect to fuel economy and a fatty amine type friction modifier had the good fuel-economy property.