• 한국자동차공학회논문집
• /
• 제24권1호
• /
• pp.33-38
• /
• 2016

The turbocharger is an essential component to realize the engine down-sizing. The moment of inertia of turbocharger rotor is an important parameter with respect to acceleration performance of the vehicle. It can be calculated from the CAD software based the geometry data and the material properties. But the accurate value of the inertia of turbocharger rotor must be measured through the experimental method. In this study, the measurement of moment of inertia of turbocharger rotor for 2.0 L spark-ignition engine was carried out. First, an experimental equipment using a trifilar method was designed and fabricated. Some optical devices, that is, photo sensor, counter, convex lens, etc, were used to increase the accuracy of the measurement. Second, error sensitivity for the equipment was analyzed. The error of period time and the radius can give big affects to the accuracy of the moment of inertia. When the amount of error of these two were each 1.0 %, maximum error of the moment of inertia was under 3.0 %. Third, the calibration for the equipment was performed using a calibration rotor which has similar shape to turbine rotor but simple. Calculated value from CAD software and measured one for the calibration rotor were compared. The total error of the equipment and the measurement is about 1.3 %. This result shows that the equipment can give the good result with resonable accuracy. Finally the moment of inertia of the turbine rotor and compressor wheel were measured. The coefficient of variations, the ratio of standard deviation to mean value, were reasonably small at 0.57 % and 0.73 % respectively. Therefore this equipment is suitable for the measurement of the moment of inertia of the turbine rotor and compressor wheel.

• 한국진공학회지
• /
• 제12권1호
• /
• pp.7-15
• /
• 2003

스피닝 로터 게이지는 표준기관의 고진공 국제비교에 전달표준기로 상용되고 있으며, 고진공 국가표준기인 동적교정장치를 이용하여 스피닝 로터 게이지를 교정하였다. 교정 결과의 불확도를 국제표준화기구에서 권고한 A형 불확도, B형 불확도, 합성표준불확도, 확장불확도 등으로 구분하여 평가하는 방법을 제시하였다. 이 방법에 따라 평가한 스피닝 로터 게이지의 합성표준불확도는 $1.8007\times10^{-5}$ Pa ~$4.8422\times10^{-5}$ Pa 이었다.

• 비파괴검사학회지
• /
• 제19권4호
• /
• pp.294-299
• /
• 1999

본 논문에서는 로타(rotor)의 초음파 탐상 결과의 신뢰성을 향상시키기 위하여 수직탐촉자에 대한 교정시스템을 개발하였다. 본 시스템은 신호처리부 (오실로스코프, 스펙트럼 분석기, 송/수신기), 표준시험편 프로그램으로 구성되어 있으며, 교정을 위한 신호처리는 높은 정밀도로 빠르게 수행할 수 있도록 구성되어 있다. 개발된 시스템을 이용하여 로타 검사에 사용되고 있는 초음파 탐촉자를 교정하고 있으며, 신뢰성 있는 정밀도와 감도를 얻을 수 있었다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.190-195
• /
• 2012

Small-scaled Rotor Test facility(GSRTS, General Small-scaled Rotor Test Facility) in KARI could not use the test because facility aging and parts discontinued. Also in order to perform a joint international research, GSRTS modifications should be needed. So requirements of GSRTS modifications were established and according to the requirements, GSRTS modifications were conducted. Facility operation test, 6-component fixed balance calibration, Small-scaled OLS rotor performance test were performed to verify the results of GSRTS modifications. Reasonable results were obtained in comparison to calculation results. Then GSRTS ready was completed to conduct international collaborative research and wind tunnel test.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 춘계학술대회 논문집
• /
• pp.387-393
• /
• 2004

General purpose of cylindrical capacitive displacement sensor(CCS) is measuring run-out motion and deflection of rotor. If CCS has narrow sensing range, its sensitivity coefficients must be calibrated precisely. And x, y component of CCS output can be coupled. In this research, CCS calibration procedure is automated with automatic calibration program and PC-controlled stage. And, coupled-terms of CCS signals were removed and the errors between measured position and mapped CCS signal were reduced obviously by sensitivity matrix that linearly.

• 한국항공우주학회지
• /
• 제37권3호
• /
• pp.301-306
• /
• 2009

본 연구에서는 축소형 로터 실험 장치에서 로터 회전면에 수직으로 작용하는 추력(Fz)과 평행으로 작용하는 2축 모멘트(Mx, My)를 측정할 수 있는 3분력 Rotating Balance를 설계, 제작하고 성능실험을 통하여 검증하였다. Rotating Balance에 장착된 스트레인게이지의 미세신호는 로터와 함께 회전하는 신호증폭기를 거쳐 증폭되어 slip ring을 통하여 데이터 취득장치로 전달되어진다. 정적 보정법을 통하여 얻어진 보정행렬식의 적합성 여부를 판단하기 위하여 기존에 개발된 reaction type balance를 사용하여, 로터가 회전시 발생하는 추력을 비교함으로서 측정 정밀도를 확인하였다. 또한, Rotating Balance의 확장 불확도는 A형 불확도와 B형 불확도를 계산하였고, 계산 결과로 부터 $2.82\times10^{-1}$의 값을 얻음으로서 신뢰성을 확인하였다.

• 대한기계학회논문집A
• /
• 제30권5호
• /
• pp.560-567
• /
• 2006

The exact load measurements for the mechanical parts of a wind turbine are important step both fur the evaluation of a specific wind turbine design and for a certification process. A common method for a mechanical load measurement is using a strain gauge sensing. Two main problems ought to be answered in order for this method to be applied to the wind turbine project. These are strain gauge calibration and non-contact signal transmission from the strain gauge output to a load monitoring system. This paper suggests reliable solutions fer these two problems. A Bluetooth, a short range wireless data communication technology, is used to solve the second problem. The first one, the strain gauge calibration methodology for a load measurement in a wind turbine application, is fully explained in this paper. Various mechanical loadings for a strain gauge calibration in a wind turbine load measurement are introduced and analyzed. Initial experimental results which are obtained from a 1 kW small size wind turbine are analyzed, and the uncertainty problem in estimating mechanical loads using a calibration matrix is fully covered in this paper.

• International Journal of Aeronautical and Space Sciences
• /
• 제17권1호
• /
• pp.120-131
• /
• 2016

The full results of troubleshooting process related to the flight control system of a tilt-rotor type UAV in the flight tests are described. Flight tests were conducted in helicopter, conversion, and airplane modes. The vehicle was flown using automatic functions, which include speed-hold, altitude-hold, heading-hold, guidance modes, as well as automatic take-off and landing. Many unexpected problems occurred during the envelope expansion tests which were mostly under those automatic functions. The anomalies in helicopter mode include vortex ring state (VRS), long delay in the automatic take-off, and the initial overshoot in the automatic landing. In contrast, the anomalies in conversion mode are untrimmed AOS oscillation and the calibration errors of the air data sensors. The problems of low damping in rotor speed and roll rate responses are found in airplane mode. Once all of the known problems had been solved, the vehicle in airplane mode gradually reached the maximum design speed of 440km/h at the operation altitude of 3km. This paper also presents a comprehensive detailing of the control systems of the tilt-rotor unmanned air vehicle (UAV).

• 한국항공우주학회지
• /
• 제32권3호
• /
• pp.10-16
• /
• 2004

본 논문에서는 축소형실험을 통하여 제자리 비행하는 헬리콥터 주로터에서 발생하는 소음의 특성을 측정하는 실험을 수행하였다. 이를 위하여 구동장치에서의 발생소음이 적은 저소음 로터시험장치를 설계/제작하였으며, 아울러 로터의 공력특성을 측정하기 위하여 작동조건에서의 회전수, 추력 및 토크를 함께 계측하였고 이에 대한 문제점을 검토하였다. 사용된 하중 측정장치의 교정을 통하여 이의 정확도를 확인하였으며, 두개의 블레이드로 구성된 직경 1.2m의 축소형 로터를 이용한 실험에서 측정된 추력값이 이론적 계산값과 비교하여 비교적 잘 일치함을 알 수 있었으나 토크 측정값은 잘 일치하지 않음을 확인하였다. 소음 측정실험을 통하여 로터 구동장치로 인한 배경소음이 로터 소음에 비하여 현저히 작음을 확인하였고, 각 로터 발생소음원의 특성에 따라 날개끝 속도에 의하여 달리 무차원화 됨을 확인하였고 방향성 특성도 변화함을 확인하였다.

• 드라이브 ㆍ 컨트롤
• /
• 제18권1호
• /
• pp.31-38
• /
• 2021

This study presents a new principle for driving the robot aimed at reducing the position error for the boresonic examination of turbine rotor. The conventional method of inspection is performed by installing manipulator onto the flange of the turbine rotor and connecting a pipe, which is then being pushed into the bore. The longer the pipe gets, the greater sagging and distortion appear, making it difficult for the ultrasonic sensor to contact with the internal surface of the bore. A pneumatic pressure will ensure the front or rear feet of the robot in close contact with the inner wall to prevent slipping, while the ball screw on the body of the robot will rotate to drive it in the axial direction. The compression force required for tight contact was calculated in the form of a three-point support, and a static structural simulation analysis was performed by designing and modeling the robot mechanism. The driving performance and ultrasonic detection ability have been tested by fabricating the robot, the test piece for ultrasonic calibration and the transparent mock-up for robot demonstration. The tests have confirmed that no slipping occurs at a certain pneumatic pressure or over.