• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.14 no.1
• /
• pp.21-33
• /
• 2016

Estimation of groundwater hydrologic cycle pattern is one of the most critical issues in sustainable management of groundwater resources in coastal area. This study estimated groundwater percolation by using the water balance methodology and hydrogeological characteristics of land use and soil. Evapotranspiration was computed by using the Thornthwaite method, and surface runoff was determined by using the SCS-CN technique. Groundwater storage change was obtained as 229 mm/a (17.8% of the average annual rainfall, 1286 mm/a), with 693 mm/a (60.1%) of evapotranspiration and 124 mm/a (9.6%) of surface runoff. Rainfall and groundwater storage change was highly correlated, comparing with the relationships between rainfall and evapotranspiration, and between rainfall and surface runoff. This result indicates that groundwater storage change responds more sensitively to precipitation than evapotranspiration and surface runoff.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1555-1559
• /
• 1997

The thin films were obtained by plasma polymerization of phenyl isothiocyanate. Polymerizations were carried out in rf(13.56[MHz]) glow discharge generated in an inter-electrode capacitively coupled gas flow system. It was found that this monomer produces uniform films with a wide range of thicknesses, from hundreds of nanometers to tens of micrometers. The deposition rate appeared to be dependent on the substrate distance from the monomer inlet. The IR data revealed significant decrease in -NCS groups content in the polymer as compared with the monomer spectrum and indicated for the appearance of new absorption bands corresponding to the -CN and C-H aliphatic groups. The soluble fraction by GC was found to be composed of numerous low molecular-weight compounds.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.8
• /
• pp.1299-1304
• /
• 2007

New sulfur functionalized cyclopentadiene ligands, 1-[2-(thioanisole)]-2,5-dimethylcyclopentadiene (3), 1-[2- (thioanisole)]-2,3,5-trimethylcyclopentadiene (4), and 1-[2-(thioanisole)]-2,3,4,5-tetramethylcyclopentadiene (5), were prepared. In these ligands, the S-donor atom is connected to a cyclopentadiene ring by a rigid phenylene spacer. CpCo(III)-diiodo half-sandwich complexes (6-8) were obtained from reaction the ligands (3- 5) with Co2(CO)8, followed by treatment of I2. Substitution reaction of CpCo(III)-diiodo complexes with MeLi yielded the corresponding CpCo(III)-dimethyl complexes (9-11). Further transformation to the corresponding cationic cobalt complexes (12-14) were achieved by reaction of the CpCo(III)-dimethyl complexes with HB(ArF)4·2Et2O and trapping with CD3CN. The new sulfur functionalized cyclopentadiene ligands having a rigid phenylene spacer and the corresponding cobalt complexes were characterized by 1H, 13C and 19F NMR spectroscopy. The diiodo Complex 6 was also characterized by a single crystal X-ray diffraction method.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.4
• /
• pp.989-998
• /
• 2010

The titled dye of DBPI gives amplified spontaneous emission (ASE) with maximum at 580 nm upon pumping by nitrogen laser (${\lambda}_{ex}\;=\;337.1\;nm$). The ground state absorption cross section (${\sigma}_A$) and emission cross section (${\sigma}_E$) as well as effective emission cross section(${\sigma}^*_E$) have been determined. The electronic absorption spectra of DBPI were measured in ethanol and tetrahydrofuran at room and low temperature. DBPI displays molecular aggregation in water. The photochemical reactivity of DBPI was also studied in carbon tetrachloride upon irradiation with 525 nm light. The electrochemical investigation of DBPI dye has been carried out using cyclic voltammetry and convolution deconvolution voltammetry combined with digital simulation technique at a platinum electrode in 0.1 mol/L tetrabutyl ammonium perchlorate (TBAP) in two different solvents acetonitrile ($CH_3CN$) and dimethylformamide (DMF). The species were reduced via consumption of two sequential electrons to form radical anion and dianion (EE mechanism). In switching the potential to positive direction, the compound was oxidized by loss of two sequential electrons, which were followed by a fast dimerization and/or aggregation process i.e $EC_{dim1}EC_{dim2}$ mechanism. The electrode reaction pathway and the chemical and electrochemical parameters of the investigated compound were determined using cyclic and convolutive voltammetry. The extracted electrochemical parameters were verified and confirmed via digital simulation method.

• YAKHAK HOEJI
• /
• v.37 no.1
• /
• pp.1-8
• /
• 1993

A procedure for the high-performance liquid chromatographic determination of Nebramycin factors in fermentation broth of Streptoalloteichus hindustanus ATCC 31218 mutant was investigated using pre-column derivatization and LTV detection. The method is based on pre-column derivatization of Nebramycin factors with 2,4-dinitrofluorobenzene(DNFB) in the presence of Tris (hydroxymethyl)aminoethane. The chromatographic separation of derivatives of Nebramycin factors and unknown impurities is achieved using reversed-phase column (NOVA-PAK $C_{18}$, Waters Co.) and AcCN : H$_{2}$O : AcOH (53.0:46.5:0.5) as a mobile phase. The mixture of these derivatives were separated within 35 minutes and the optimum wavelength($\lambda_{max}$ ) of the UV detector was 353 nm. The linearity of response for derivatives of Nebramycin factors is demonstrated for concentrations up to 500 $\mu\textrm{g}$/ml and the relative standard deviation is less than 0.79%. Detection limit was 1.67 ng for the 10 $\mu\textrm{l}$ sample volume employed.

• Membrane and Water Treatment
• /
• v.5 no.3
• /
• pp.171-182
• /
• 2014

Organic compounds are adsorbed on RO/NF membranes, and the adsorption may influence the rejection of organic compounds by the membranes. Because almost RO/NF membranes are composite membranes, the results obtained by adsorption experiment with using membrane pieces are unable to avoid the influence by the support membrane. In this work, the interaction between membrane polymer and organic solutes was examined by an inverse HPLC methodology. Poly (m-phenylenetrimesoylate), the constituent of skin layer of RO/NF membranes, was coated on silica gel particles and used as a stationary phase for HPLC. When water was used as a mobile phase, almost hydrophilic aliphatic compounds were not effectively adsorbed on the stationary phase, although hydrophobic compounds were slightly adsorbed. The results indicated that the hydrophilic aliphatic compounds are useful probe solutes to examine the molecular sieving effect of a membrane. When water was used as a mobile phase, the aromatic compounds were strongly retained, and therefore $CH_3CN/H_2O$ (30/70) was used as a mobile phase. It was revealed that the adsorption of aromatic compounds was controlled by stacking between solute and polymer and was hindered by non-planar structure and substituents.

• Analytical Science and Technology
• /
• v.20 no.1
• /
• pp.55-60
• /
• 2007

A sensitive technique for the determination of trace Cu(II) in various samples after the column preconcentration by adsorbing its N-benzoylphenylhydroxylamine (BPHA) onto benzophenone was developed. Several experimental conditions such as the pH of the sample solution, the amount of chelating agent, the amount of benzophenone, and the flowrate of sample solution and so forth were optimized. The interfering effects of diverse concomitant ions were investigated. Fe(III) and $CN^-$ interfered with more seriously than any other ions. However, the interference by these ions could be overcome sufficiently by adjusting the added volume of 0.01M BPHA to 10 mL. The dynamic range, the correlation coefficient ($r^2$) and the detection limit obtained by this proposed technique were 5.0~120 ng/mL, 0.9974, and 2.1 ng/mL, respectively. For validating this proposed technique, the aqueous samples (stream water, reservoir water, and wastewater), the plastic sample and the diluted brass sample were used. Recovery yields of 93~102% were obtained. These measured data were not different from ICP-MS data at 95% confidence level. This method was also validated by the rice flour CRM (normal, fortified) samples. Based on the results from the experiment, it was found that this proposed technique could be applied to the determination of Cu(II) in various real samples.

• Journal of the Korean GEO-environmental Society
• /
• v.13 no.1
• /
• pp.45-51
• /
• 2012

This article aims to find method to mix a harmless hardening agent and soil generated during construction to make paving materials. The main purpose of this research is to get rid of the harmfulness(Chromium (VI), etc.) of cement which has been generally and frequently used as a hardening agent and strengthen it so that it can be used for the general foundation solidification and stabilization of civil engineering/construction structures such as dredging soil treatment, marine structure foundation treatment, surface soil stabilization, and river bank erosion prevention. NSS(Natural Stabilizer Soil) used for this study takes as its chief ingredient the mixture of lime and staple fibers extracted from natural fibers. It increases the shearing strength of soil that it improves the support and durability of the foundation and prevents flooding and frost as well. The pH measured to know its eco-friendliness was 6.67~7.15, and according to the migration testing, only Pb and CN were lower than the standards, so it can be said that NSS has almost no harmful components in it. According to the result of uniaxial strength testing, when the mixture ratio of weathered soil to NSS was 6%, about 1,850kpa strength was expressed. And according to the result of CBR. testing to figure out its appropriateness as a paving material, the CBR of the foundation was 4%~6%. But when the mixture ratio of NSS is over 6%, the water immersion CBR. is over 100%; thus, it is expected that it will show great utility as a paving material.

• Korean Journal of Food Science and Technology
• /
• v.24 no.3
• /
• pp.256-260
• /
• 1992

This study was conducted to calculate and predict the shelf-life of meat sausage through physicochemical and biological analysis. Judging from physico-chemical components, it can be found out the most effective indicator in meat sausage. And also, the materials used for packaging is cellulose #23 in inner-packaging and CN/HDPE laminating film in outer-packaging. The changes of the most effective indicator were discussed through the method of kinetic analysis. Judging from physico-chemical components, VBN was the most available component in quality judgement of meat sausage and their upper limiting contents were 20 mg%. It is possible to calculate and predict the shelf-life of meat sausage through the regression equation and $Q_{10}$ value. As a result, the shelf-life prediction was $58{\sim}63$ days at $10^{\circ}C$, $47{\sim}51$ days at $20^{\circ}C$ and 26 days at $40^{\circ}C$, respectively, but the difference between two methods showed about $4{\sim}5$ days. $Q_{10}$ value on the changes contents was 1.35 at acceralated temperature $40^{\circ}C$. The reaction rate of VBN contents could be interpreted as a first order reaction that divided into 2 periods with different reaction rate constants. The corresponding Arrhenius activation energies were 2.959 Kcal/mole and 3.632 Kcal/mole, respectively.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2005.05b
• /
• pp.553-557
• /
• 2005

유역의 강우-유출 분석에서 유효우량의 산정은 매우 중요하다고 할 수 있다. 이러한 유효우량의 산정에서 대상호우에 대한 유출량 자료가 있는 경우는 침투지수법(infiltration index method)중 하나인 $\Phi$-지표법이나 W-지표법을 사용하여 그 양을 산정할 수 있다. 그러나 대상호우에 대한 유출량 자료가 없는 경우는 침투지수법을 이용하여 유효우량을 산정 할 수 없으며, 이러한 경우 유역의 토양 특성과 식생피복 상태에 대한 자료만으로 총우량으로부터 유효우량을 산정할 수 있는 NRCS(Natural Resources Conservation Service)의 유효우량 산정방법이 널리 사용되고 있다. NRCS유효우량 산정 방법은 선행토양함수조건(antecedent moisture condition, AMC)을 이 용하여 유출곡선지수(runoff curve number, CN)를 결정하는데, 이때 AMC의 산정을 위해 선행5일강우량(total 5-day antecedent rainfall)을 그 기준으로 하고 있으나, 이는 미국의 유역을 대상으로 하여 얻어진 결과이므로 이를 국내 유역에 검증 없이 적용하는 데에는 문제가 있을 것으로 예상되었다. 따라서 본 연구에서는 HEC-HMS모형을 이용하여 선행강우일수을 변화시켜 가면서 실제 유역의 강우-유출에 적용하여 본 뒤 강우-유출을 가장 잘 모의하는 선행강우일수을 결정하였다. 이를 위해, IHP 대상유역인 보청천의 탄부소유역에 대하여 AMC의 산정을 위한 선행강우량을 1일부터 7일까지 변화시키며 적용한 결과 탄부소유역에서는 선행2일강우량이 가장 적합한 결과를 주는 것으로 나타났다. 국내 유역에서 NRCS유효유량 산정방법을 통한 강우-유출모의시 보다 정확한 값을 산정하기 위해서는 대상유역에 적합한 선행 강우일수의 결정이 중요하리라 판단된다.인 분석을 수행하고, 배수갑문 개방에 의한 수질개선효과를 최대화하기 위한 환경관리 방안 제시에 중점을 두어 수행하였다.ncy), 환경성(environmental feasibility) 등을 정성적으로(qualitatively) 파악하여 실현가능한 대안을 선정하였다. 이렇게 선정된 대안들은 중유역별로 검토하여 효과가 있을 것으로 판단되는 대안들을 제시하는 예비타당성(Prefeasibility) 계획을 수립하였다. 이렇게 제시된 계획은 향후 과학적인 분석(세부평가방법)을 통해 대안을 평가하고 구체적인 타당성(feasibility) 계획을 수립하는데 토대가 될 것이다.{0.11R(mm)}(r^2=0.69)$로 나타났다. 이는 토양의 투수특성에 따라 강우량 증가에 비례하여 점증하는 침투수와 구분되는 현상이었다. 경사와 토양이 같은 조건에서 나지의 경우 역시 $Ro_{B10}(mm)=20.3e^{0.08R(mm)(r^2=0.84)$로 지수적으로 증가하는 경향을 나타내었다. 유거수량은 토성별로 양토를 1.0으로 기준할 때 사양토가 0.86으로 가장 작았고, 식양토 1.09, 식토 1.15로 평가되어 침투수에 비해 토성별 차이가 크게 나타났다. 이는 토성이 세립질일 수록 유거수의 저항이 작기 때문으로 생각된다. 경사에 따라서는 경사도가 증가할수록 증가하였으며 $10\% 경사일 때를 기준으로 $Ro(mm)=Ro_{10}{\times}0.797{\times}e^{-0.021s(\%)}$로 나타났다.천성 승모판 폐쇄 부전등을 초래하는 심각한 선천성 심질환이다. 그러나 진단 즉시 직접 좌관상동맥-대동맥 이식술로 수술적 교정을 해줌으로써 좋은 성적을 기대할 수 있음을 보여주었다.특히 교사들이 중요하게 인식하는 해방적 행동에 대한 목표를 강조하여 적용할 필요가 있음을 시사하고