• 한국해양학회지
• /
• v.26 no.4
• /
• pp.340-349
• /
• 1991

From tidal current measurements on a tidal sand ridge in the Gyeonggi Bay from August 24 to September 29, 1987, tidal current velocities at 1.0 m above bottom (U/SUB 100/) and boundary shear velocities (U/SUB */) are calculated. The mean speeds of tidal current for flood and ebb over the entire period are 56.3 cm/sec and 63.7 cm/sec in mid-depth (9.0 m above bottom), and 43.9 cm/sec and 43.8 cm/sec in near-bottom (1.5 m above bottom). The exponent(P) in "power law", which is generally used for extrapolation from the mid-depth current velocity to that at the top of nationally logarithmic layer, is estimated to be 0.15 in the study area. Using logarithmic velocity profile assumption, mean values of U/SUB 100/ and U/SUB */ are calculated to be 41.4 cm/sec and 2.39 cm/sec, respectively. The mean value of U/SUB */ (2.39 cm/sec) is much higher than the critical shear velicity (U/SUB *c/) of 1.40 cm/sec reported by Choi (1990). and thus, it can be suggested that the most of sands on the tidal sand ridge in the study area are easily eroded and transported for the greater part of tidal period.

• Journal of the Korean Wood Science and Technology
• /
• v.27 no.2
• /
• pp.38-45
• /
• 1999

This study was to figure out proper Formaldehyde/Urea molar ratio of UF resin with satisfactory bonding strength of plywood and properties of particleboard. The six kinds of UF resins were manufactured with F/U molar ratio 1.0, 1.2, 1.4, 1.6, 1.8, and 2.0. The boards were made of three kinds of raw materials : Veneer, Sliver-Particle and Strand-Particle. Manufacturing condition of plywood : amount of mixing resin was 150g/$m^2$. The fourty secs/mm simple-pressing schedule in the pressure 10kgf/$m^2$ was applied for 480mm${\times}$700mm board at the temperature of $110^{\circ}C$ in a hot press. Manufacturing condition of particleboard : Target density was 0.65g/$cm^2$. The stepwise 9 minutes- multi-pressing schedule in the maximum pressure 40kgf/$cm^2$, the minimum pressure 15kgf/$cm^2$ was applied for $480mm{\times}634mm{\times}12mm$ board at the temperature of $150^{\circ}C$ in a hot press. The results are as follows : I. In bonding strength, plywood which was made by F/U molar ratio 1.2 showed the highest value. Other molar ratio resin also gave the satisfied value of KS standard, 7.5kgf/$cm^2$. 2. In internal bond strength of particleboard, Sliver-Particleboard(SLPB) and Strand-Particleboard(STPB) varied respectively from 5.9kgf/$cm^2$ to 4.8kgf/$cm^2$, from 6.7kgf/$cm^2$ to 5.4kgf/$cm^2$. SLPB with F/U=1.2 and STPB with F/U=1.6 had higher IB value. Also, both SLPB and STPB showed lower IB value in F/U molar ratio 2.0 and 1.0. 3. SLPB and STPB with six kinds of UF resin respectively satisfied bending strength of KS standard 150 Type(130kgf/$cm^2$) and 200 Type(180kgf/$cm^2$). Bending strength data for both of SLPB and STPB showed little or no loss from F/U=1.8 to F/U=1.2. Also, STPB was approximately two times higher than that of SLPB. Therefore, the raw material's shape had more effect on bending strength than the FlU molar ratio. 4. F/U=1.6 and 1.4 showed the lower thickness swelling in SLPB and STPB. All of STPBs satisfied thickness swelling of KS standard, under 12%.

• Journal of Chitin and Chitosan
• /
• v.23 no.4
• /
• pp.228-233
• /
• 2018

We isolated microorganisms from soil, which is sampled at forest, Kyeonbuk, Korea, as cellulolytic microorganisms. The isolated strains were identified by analysis of 16S rRNA gene from the starins. The result, four kinds of Bacillus subtilis, one kind of Bacillus amyloliquefaciens, and one kind of Bacillus cereus were identified. Among these strains, Bacillus subtilis was selected due to its high cellulase activity and this strain was named as Bacillus subtilis CNS. The optimum pH and temperature of the cellulase from Bacillus subtilis CNS was pH 5.0 and $40^{\circ}C$, respectively. In the investigation of pH and temperature stability, the cellulase from Bacillus subtilis NSC stabled pH 4.0~6.0 range and until $40^{\circ}C$ for 30 min perfectly. In the enzyme activity for various cellulosic substrate, cellulase from Bacillus subtilis CNS showed the highest activity for CM-cellulose. And, the enzyme activities for alkali swollen cellulose, Alpha-cellulose, Sigmacell-cellulose, and Avicel were approximately 31%, 8%, 8% and 4% of activity for CM-cellulose, respectively. In the degradation of CM-cellulose, the 0.26 U/ml and 0.52 U/ml of cellulase showed 0.43 and 0.76 U/ml activity for CM-cellulose after the reaction of 120 min, respectively.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.6 no.3
• /
• pp.225-232
• /
• 2008

An estimation has been made for inventories and characteristics of spent nuclear fuel(SNF) to be generated from existing and planned nuclear power plants based on the 3rd Basic Plan for Electric Power Demand and Supply. The characteristics under consideration in this study are dimensions, a fuel rod array, a weight, $^{235}U$ enrichment, and the discharge burnup in terms of fuel assembly. These are essentially needed for designing a pyroprocessing facility. It is appeared that the anticipated quantity by the end of 2077 is about 23,000 tU for PWR spent nuclear fuel. It is revealed that the proportion of SNF with the initial $^{235}U$ enrichment below 4.5 weight percent(wt.%) is approximately 95 % in total. For SNF with 16$\times$16 fuel rod array the proportion is expected approximately 74% in total. It appears that the average burnup of SNF will be 55 GWd/tU after the medium and/or latter part of 2010s while the average burnup is 45 GWd/tU at present. Finally, a requirement in terms of reference SNF for designing the pyroprocessing facility has been derived from the above-mentioned results. The anticipated SNF seems to be 16$\times$16 Korean Standard Fuel Assembly with a cross section of 21.4 cm$\times$21.4 cm, a length of 453 cm, a mass of 672 kg, the initial $^{235}U$ enrichment of 4.5 wt.%, and the discharge burnup of 55 GWd/tU.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.1
• /
• pp.33-46
• /
• 2010

We investigated and estimated at the characteristics of decomposition and by-products of N-Nitrosodimethylamine (NDMA) using a design of experiment (DOE) based on the Box-Behken design in an UV process, and also the main factors (variables) with UV intensity($X_2$) (range: $1.5{\sim}4.5\;mW/cm^2$), NDMA concentration ($X_2$) (range: 100~300 uM) and pH ($X_2$) (rang: 3~9) which consisted of 3 levels in each factor and 4 responses ($Y_1$ (% of NDMA removal), $Y_2$ (dimethylamine (DMA) reformation (uM)), $Y_3$ (dimethylformamide (DMF) reformation (uM), $Y_4$ ($NO_2$-N reformation (uM)) were set up to estimate the prediction model and the optimization conditions. The results of prediction model and optimization point using the canonical analysis in order to obtain the optimal operation conditions were $Y_1$ [% of NDMA removal] = $117+21X_1-0.3X_2-17.2X_3+{2.43X_1}^2+{0.001X_2}^2+{3.2X_3}^2-0.08X_1X_2-1.6X_1X_3-0.05X_2X_3$ ($R^2$= 96%, Adjusted $R^2$ = 88%) and 99.3% ($X_1:\;4.5\;mW/cm^2$, $X_2:\;190\;uM$, $X_3:\;3.2$), $Y_2$ [DMA conc] = $-101+18.5X_1+0.4X_2+21X_3-{3.3X_1}^2-{0.01X_2}^2-{1.5X_3}^2-0.01X_1X_2+0.07X_1X_3-0.01X_2X_3$ ($R^2$= 99.4%, 수정 $R^2$ = 95.7%) and 35.2 uM ($X_1$: 3 $mW/cm^2$, $X_2$: 220 uM, $X_3$: 6.3), $Y_3$ [DMF conc] = $-6.2+0.2X_1+0.02X_2+2X_3-0.26X_1^2-0.01X_2^2-0.2X_3^2-0.004X_1X_2+0.1X_1X_3-0.02X_2X_3$ ($R^2$= 98%, Adjusted $R^2$ = 94.4%) and 3.7 uM ($X_1:\;4.5\;$mW/cm^2$, $X_2:\;290\;uM$, $X_3:\;6.2$) and $Y_4$ [$NO_2$-N conc] = $-25+12.2X_1+0.15X_2+7.8X_3+{1.1X_1}^2+{0.001X_2}^2-{0.34X_3}^2+0.01X_1X_2+0.08X_1X_3-3.4X_2X_3$ ($R^2$= 98.5%, Adjusted $R^2$ = 95.7%) and 74.5 uM ($X_1:\;4.5\;mW/cm^2$, $X_2:\;220\;uM$, $X_3:\;3.1$). This study has demonstrated that the response surface methodology and the Box-Behnken statistical experiment design can provide statistically reliable results for decomposition and by-products of NDMA by the UV photolysis and also for determination of optimum conditions. Predictions obtained from the response functions were in good agreement with the experimental results indicating the reliability of the methodology used.

• Journal of radiological science and technology
• /
• v.41 no.5
• /
• pp.445-450
• /
• 2018

We aim to evaluate safety of radiation by measuring leakage dose and patient(phantom) incident dose of ZEN-PX II dental portable equipment developed by G company. Measurement for leakage dose of equipment is conducted on the top, at the bottom, on the left, on the right and at the back. Dose measurement incident on the subject with the area dosimeter when using the phantom and measurement the leakage dose of equipment when using the phantom are evaluated. Comparing the right with the highest leakage dose as a 0 cm, 25 cm, 50 cm, 75 cm and 100 cm dose measurement at the measurement height of 100 cm, 64.2 uR was reduced to 47.3 uR in the senser mode 0.32sec. Even in film mode it was measured at 414.4 uR and about 27% lower at 162.6 uR. As the result of this study, when the irradiation time is 2 sec the right side dose is 290.5 uR and sensor mode is 0.32 sec the right side dose is 64.2 uR.

• KSBB Journal
• /
• v.13 no.1
• /
• pp.44-51
• /
• 1998

Hydrolysis and adsorption reversibility experiments were run for initial enzyme activity of 4.48, 9.65, 11.19 and 17.14U/mL at a temperature 30$^\circ C$. The chitin particle size corresponded to a mean particle diameter of 0.127mm, and the initial concentration of chitin was 10mg/mL. After approximately 2hrs, the enzyme activity remained constant in a speudo-steady state. The amounts in the bulk [E] and the amounts of enzyme adsorbed on the chitin surface [E] are plotted on Lineweaver-Burk plot to yield a linear relationship with a correlation coefficient of 0.99, a slope of 2.79cm$^-1$ and an intercept of 0.08$\textrm{cm}^2$/U. From this parameters, the values of [E$_T$] and $K_E$ were calculated to be 12.5U/cm$^2$ and 34.88U/mL. respectively, Adsorption isotherm of the enzyme on the particles showed a well developed plateau of 1.35$\times$10$^-3$, 4.72$\times$10$^-3$, 4.42$\times$10$^-3$, 8.58$\times$10$^-3$U/cm$^2$ at 30$^\circ C$. To determine the specificity of chitinase for crystalline chitin, the free energy of adsorption was measured, and its was determined as about -14.62~-18.8kJ/mol.

• Journal of Plant Biology
• /
• v.26 no.4
• /
• pp.181-190
• /
• 1983

Seasonal occurrence of benthic algae and changes of subtidal vegetation were studied for their species composition, diversity and biomass during 1982 and 1983 at several selected sites at Juckdo Island (38$^{\circ}$12'N, 128$^{\circ}$32'E), eastern coast of Korea. Three large brown algae which played a role in change of algal vegetation through their great biomass were investigated with regard to their seasonal growth. Large brown algae such as Undaria pinnatifida, Costaria costata, Laminaria japonica, Agarum cribrosum, Sargassum confusum and S. hornerii constitute the major portion of vegetation in this area throughout the year. Algal vegetation in spring time is characterized by dominance of species U. pinnatifida and C. costata, whereas the summer vegetation by S. confusum and S. hornerii. In autumn large brown algae are shedded and only small algae, such as Chondrus ocellatus and Grateloupia filicina, remain. The vegetation in winter is dominated by the growth of U. pinnatifida and C. costata. Monthly changes in mean length and weight of randomly collected U. pinnatifida, C. costata and S. confusum are as follows; U. pinnatifida occurs from December to June and shows their maximum growth during March (120 cm in length, 201 g/individual in wet weight), its maximum growth rate is 1.4 cm/day, 3.3 g/day in this month. The growth season of C. costata is very similar to U.pinnatifida, but their average maximum length(110 cm) and weight (106 g/ind.) are lower than U. pinnatifida. The greatest growth rate is during March (1.8 cm/day, 2.0g/day). S. confusum is present throughout the year and reaches the maximum growth (102 cm, 63g/ind.) in July. Maximum growth rate (1.5 cm/day, 1.2 g/day) occurs also during this month. U. pinnatifida and C. costata show different months of maximum growth evidently during the two year. This seems to be caused by a considerable damage to the local vegetation followed by heavy storm in February 1983.

• Structural Engineering and Mechanics
• /
• v.83 no.4
• /
• pp.495-513
• /
• 2022

This paper aims to study the fracture mechanism of rocks under the 'u'shape cutters considering the effects of crack (pre-existing crack) distances, crack spacing and crack inclination angles. The effects of loading rates on the rock fragmentation underneath these cutters have been also studied. For this purpose, nine experimental samples with dimensions of 5 cm×10 cm×10 cm consisting of the non-persistent cracks were prepared. The first three specimens' sets had one non-persistent crack (pre-existing crack) with a length of 2 cm and angularity of 0°, 45°, and 90°. The spacing between the crack and the "u" shape cutter was 2 cm. The second three specimens" set had one non-persistent crack with a length of 2 cm and angularity of 0°, 45°, and 90° but the spacing between pre-existing crack and the "u" shape cutter was 4 cm. The third three specimens'set has two non-persistent cracks with lengths of 2 cm and angularity of 0°, 45° and 90°. The spacing between the upper crack and the "u" shape cutter was 2 cm and the spacing between the lower crack and the upper crack was 2 cm. The samples were tested under a loading rate of 0.005 mm/s. concurrent with the experimental investigation. The numerical simulations were performed on the modeled samples with non-persistent cracks using PFC2D. These models were tested under three different loading rates of 0.005 mm/s, 0.01 mm/sec and 0.02 mm/sec. These results show that the crack number, crack spacing, crack angularity, and loading rate has important effects on the crack growth mechanism in the rocks underneath the "u" shape cutters. In addition, the failure modes and the fracture patterns in the experimental tests and numerical simulations are similar to one another showing the validity and accuracy of the current study.

• Progress in Medical Physics
• /
• v.18 no.2
• /
• pp.55-64
• /
• 2007

Our objective was to evaluate the clinical feasibility of spatial domain filtering as an alternative to additional image reconstruction using different kernels in CT. Kernels were grouped as H30 (head medium smooth), B30 (body medium smooth), S80 (special) and U95 (ultra sharp). Derived from thin coilimated source images, four sets of images were generated using phantom kernels. MTF (50%, 10%, 2%) measured with H30 (3.25, 5.68, 7.45 Ip/cm) B30 (3.84, 6.25, 7.72 Ip/cm), S80 (4.69, 9.49, 12.34 Ip/cm), and U95 (14.19, 20.31, 24.67 Ip/cm). Spatial resolution for the U95 kernel (0.6 mm) was 33.3% greater than that of the H30 and B30 (0.8 mm) kernels. Initially scanned kernels images were rated for subjective image qualify, using a five-point scale. Image scanned with a convolution kernel led to an increase in noise (U95), whereas the results for CT attenuation coefficient were comparable. CT images increase the diagnostic accuracy in head (H30), abdomen (B30), temporal bone and lung (U95) kernels may be controlled by adjusting CT various algorithms, which should be adjusted to take into account the kernels of the CT undergoing the examination.