• 한국수산과학회지
• /
• 제53권1호
• /
• pp.43-49
• /
• 2020

The maturation and spawning of red seabream Pagrus major were investigated using 1,014 samples collected monthly from January to December of 2018, in the South Sea of Korea. Based on monthly changes in maturity stage and gonadosomatic index, the spawning period was estimated to be between April and August, with peak spawning occuring from May to June. Fecundity varied between 228,996 and 4,544,948 eggs. The relationship between fecundity (F) and fork length (FL) in this species can be expressed by the equation F=0.4869FL^3.9452 (R²=0.7448). Using a logistic function, the percentage of sexually mature females was estimated to be over 50% for fish with a FL of 35.3 cm.

• 한국의학물리학회지:의학물리
• /
• 제27권3호
• /
• pp.162-168
• /
• 2016

Proton therapy is increasingly being actively used in the treatment of cancer. In contrast to photons, protons have the potential advantage of delivering higher doses to the cancerous tissue and lower doses to the surrounding normal tissue. However, a range shifter is needed to degrade the beam energy in order to apply the pencil beam scanning technique to tumors located close to the minimum range. The secondary neutrons are produced in the beam path including within the patient's body as a result of nuclear interactions. Therefore, unintended side effects may possibly occur. The research related to the secondary neutrons generated during proton therapy has been presented in a variety of studies worldwide, since 2007. In this study, we measured the magnitude of the secondary neutron dose depending on the location of the detector and the use of a range shifter at the beam nozzle of the proton scanning mode, which was recently installed. In addition, the production of secondary neutrons was measured and estimated as a function of the distance between the isocenter and detector. The neutron dose was measured using WENDI-II (Wide Energy Neutron Detection Instruments) and a Plastic Water phantom; a Zebra dosimeter and 4-cm-thick range shifter were also employed as a phantom. In conclusion, we need to consider the secondary neutron dose at proton scanning facilities to employ the range shifter reasonably and effectively.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.217.2-217.2
• /
• 2014

We prepared a flexible and transparent CuO/Cu/CuO multilayer electrodes on a polyethylene terephthalate (PET) substrate using a specially designed roll-to-roll sputtering system at room temperature for GFF-type touch screen panels (TSPs). By the continuous roll-to-roll sputtering of the CuO and Cu layer, we fabricated a flexible CuO(150nm)/Cu(150nm)/CuO(150nm) multilayer electrodes with a sheet resistance of $0.289{\Omega}/square$, resistivity of $5.991{\times}10^{-23}{\Omega}-cm$, at the optimized condition without breaking the vacuum. To investigate the feasibility of the CuO/Cu/CuO multilayer as a transparent electrode for GFF-type TSPs, we fabricated simple GFF-type TSPs using the diamond patterned CuO/Cu/CuO electrode on PET substrate as function of mesh line width. Using diamond patterned CuO/Cu/CuO electrode of mesh line $5{\mu}m$ with sheet resistance of 38 Ohm/square, optical transmittance of 90% at 550 nm and an average transmittance of 89% at wavelength range from 380 to 780 nm, we successfully demonstrated GFF-type touch panel screens (TPSs). The successful operation of GFF-type TPSs with CuO/Cu/CuO multilayer electrodes indicates that the CuO/Cu/CuO multilayer is a promising transparent electrode for large-area capacitive-type TPSs due to its low sheet resistance and high transparency.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.478.1-478.1
• /
• 2014

We investigated $MoO_3$ graded ITO electrodes for organic solar cells (OSCs) without PEDOT:PSS buffer layer. The effect of $MoO_3$ thickness on the electrical, optical, and structural properties of $MoO_3$ graded ITO anodes prepared by RF/DC magnetron co-sputtering system using $MoO_3$ and ITO targets was investigated. At optimized conditions, we obtained $MoO_3$ graded ITO electrodes with a low sheet resistance of 13 Ohm/square, a high optical transmittance of 83% and a work function of 4.92 eV, comparable to conventional ITO films. Due to the existence of $MoO_3$ on the ITO electrodes, OSCs fabricated on $MoO_3$ graded ITO electrode without buffer layer successfully operated. Although OSCs fabricated on ITO anode without buffer layer showed a low power conversion efficiency of 1.249%, OSCs fabricated on $MoO_3$ graded ITO electrode without buffer layer showed a outstanding cell performance of 2.545%. OSCs fabricated on the $MoO_3$ graded ITO electrodes exhibited a fill factor of 61.275%, a short circuit current of 7.439 mA/cm2, an open circuit voltage of 0.554 V, and a power conversion efficiency of 2.545%. Therefore, $MoO_3$ graded ITO electrodes can be considered a promising transparent electrode for cost efficient and reliable OSCs because it could eliminate the use of acidic PEDOT:PSS buffer layer.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.257.1-257.1
• /
• 2014

We investigated characteristics of ITO/Ag-Pd-Cu (APC)/ITO multilayer electrodes prepared by direct current magnetron sputtering for use as an anode in organic solar cells (OSCs). To optimize electrical properties of ITO/APC/ITO multilayer, we fabricated the ITO/APC/ITO multilayer at a fixed ITO thickness of 30 nm as a function of APC thickness. Compare to the surface of Ag layer on ITO, the APC had a smooth surface morphology. At optimized APC thickness of 12 nm, the ITO/APC/ITO multilayer exhibited a sheet resistance of $6{\Omega}/square$ and optical transmittance of 84.15% at a wavelength of 550 nm which is comparable to conventional ITO/Ag/ITO multilayer. However, the APC-based ITO multilayer showed a higher average transmittance in a visible region than the Ag-based ITO multilayer. The higher average transmittance of ITO/APC/ITO multilayer indicated the multilayer is suitable anode for organic solar cells with P3HT:PCBM active layer. OSCs fabricated on the optimized ITO/ACP/ITO multilayer exhibited a better performance with a fill factor of 64.815%, a short circuit current of $8.107mA/cm^2$, an open circuit voltage of 0.59 V, and power conversion efficiency (3.101%) than OSC with ITO/Ag/ITO multilayer (2.8%).

• 한국재료학회지
• /
• 제9권5호
• /
• pp.496-502
• /
• 1999

In this study, n-GaN samples were etched using planar inductively coupled $Cl_2$/$H_2$plasmas and the effects of plasma conditions on the etch properties, surface composition, and ohmic contact formation were investigated as a function of gas combination. As the addition of hydrogen to the $Cl_2$plasma increased to 100%, GaN etch rates decreased due to the reduction of chlorine radical density. Even though the variation of the surface composition is limited under $50\AA$, the surface composition was also changed from Ga-rich to N-rich with the increased addition of hydrogen to $Cl_2$. Etch products by the reaction between Ga in GaN and Cl in $Cl_2$ plasma were investigated using OES analysis during the GaN etching. The value of specific resistivity of the contact formed on the n-GaN etched using 100% $Cl_2$plasma was 3.1$\times$10\ulcorner$\Omega$$\textrm{cm}^2$, and which was lower than that formed on the non-etched n-GaN. However, the resistively was increased with the increased hydrogen percent in $Cl_2$/$H_2$.

• 한국전기전자재료학회논문지
• /
• 제16권6호
• /
• pp.490-495
• /
• 2003

The electromagnetic properties and thermal behavior of Mn-Zn ferrite cores for the blocking filter of Power Line Communication(PLC) application were investigated as a function of additives. The highest density and permeability were 4.98 g/$\textrm{cm}^2$ and 8,221, respectively and were obtained to the specimen with composition of MnO 24 mol%, ZnO 25 mol% and Fe$_2$O$_3$ mol%, added MoO$_3$ of 400 ppm, SiO$_2$ of 100 ppm, and CaO of 200 ppm. The uniform grains were organized, and the microstructures were densified due to reduction of pores in the specimen. The permeability was increased up to 13,904 as the temperature of specimen increased to 110$^{\circ}C$. However, it was decreased precipitously under 100 over 110$^{\circ}C$. The exothermic behavior was observed in the frequency range from 1 kHz to 1 MHz, and the maximum temperature of specimen was 102$^{\circ}C$ at 1 MHz. In the consequence, the Mn-Zn ferrite core developed in this research will maintain the stable electromagnetic properties since the temperature of ferrite core rose to 93$^{\circ}C$ in the range of 100 kHz to 450 kHz bandwidth qualified for PLC. The blocking filters were designed for single phase and three phases using the in-line and non-contact core. The best attenuation ratios of -46.46 dB and -73.9 dB were measured in the range of 100 kHz to 450 kHz bandwidth, respectively.

• 한국의류학회지
• /
• 제34권5호
• /
• pp.819-830
• /
• 2010

This study proposes medical gowns for interns and residents that address the functions of utility and activity. Based on the questionnaires, the prototype focused on the pockets for practical use and movement adaptability. Functional pockets were made by increasing pocket sizes and separating pockets with sections according to use. An inside pocket and a loop for an identification tag was placed on the chest pocket and the side seam pocket were oblique lined. To resolve horizontal stress on the back of the gown,6 cm action pleats were added at both ends of the bladebone. The elbow area was tucked up to improve the workplace activities. To reduce hamper on the gown hemline, slits were added along the gown side seam. The front button was changed into an inside button closure. The cuffs, belt, and back waist belt were removed due to occupational cases of inconvenience. The length of the sleeves was adjusted with belts to improve the movement of the arms. In accordance with design preference, the gown was designed to be knee-length with wrist length sleeves. Blue colored (2.5PB 3/12: by Munsell) material was inserted to reduce the contamination on the neck, cuffs, front closure, and hemline area. The planning cloth of the experimental gown was designed to improve activity function, cleaning, and comfort from light materials. The field test (with 30 doctors at university hospitals and the objective assessment with 9 subject groups)were done by the valuation between the existing gown and the prototype. The results showed that the prototype had to be modified by decreasing the pocket size, expanding the usage of the penholder, and simplify front pockets in order to maintain unity. The loop for the identification tag, inside pocket, and the blue colored material had to be removed. The front closure of the gown had to return to its original state.

• Journal of Biosystems Engineering
• /
• 제36권1호
• /
• pp.15-22
• /
• 2011

An experimental variable rate nursery sprayer was developed to adjust application rates for canopy volume in real time. The sprayer consisted of two vertical booms integrated with ultrasonic sensors, and variable rate nozzles coupled with pulse width modulation (PMW) based solenoid valves. A custom-designed microcontroller instructed the sensors to detect canopy size and occurrence and then controlled nozzles to achieve variable application rates. A spray delivery system, which consisted of diaphragm pump, pressure regulator and 4-cycle gasoline engine, offered the spray discharge function. Spray delay time, time adjustment in spray trigger for the leading distance of the sensor, was measured with a high-speed camera, and it was from 50 to 140 ms earlier than the desired time (398 ms) at 3.2 km/h under indoor conditions. Consequently, the sprayer triggered 4.5 to 12.5 cm prior to detected targets. Duty cycles of the sprayer were from 20 to 34 ms for senor-to-canopy (STC) distance from 0.30 to 0.76 m. Outdoor test confirmed that the nozzles were triggered from 290 to 380 ms after detecting tree canopy at 3.2 km/h. The spray rate of the new sprayer was 58.4 to 85.2% of the constant application rate (935 L/ha). Spray coverage was collected at four areas of evergreen canopy by water sensitive papers (WSP), and ranged from 1.9 to 41.1% and 1.8 to 34.7% for variable and constant rate applications, respectively. One WSP area had significant (P < 0.05) difference in mean spray coverage between two application conditions.

• Archives of Plastic Surgery
• /
• 제36권4호
• /
• pp.497-499
• /
• 2009

Purpose: Leiomyoma is a rare benign tumor of nonstriated muscles. Leiomyoma is most commonly found in the uterus and rarely occur in the hand. 150 cases of leiomyoma of the hand have been reported in the English literature; however, to the best of our knowledge only four of these have been in children and none were reported in Korean literature. We present a case of leiomyoma in the hand of a 8 - year - old boy, which is a rare site for localization and unusual for age. Methods: A 8 - year - old boy presented with a painless mass on the ulnar side of his thumb. Physical examination revealed a $1.2{\times}1.2cm$ round, rubbery mass that was nontender to palpation. The vascular, sensory, and motor exams were otherwise unremarkable. Further evaluation with CT demonstrated an enhancing mass at dorsoulnar aspect of 1st proximal phalangeal region suggestive of a hemangioma versus other enhancing solid mass. The diagnosis of a leiomyoma was confirmed following surgical excision with histologic evaluation. Results: At 3 months follow - up, the incision was healed, motor and sensory function were intact, and there were full range of motion. Neither recurrence nor postoperative complication were observed. Conclusion: Leiomyoma is a rare tumor of the hand, especially in children. Diagnosing hand tumors in children is more difficult than in adults, hand surgeons should be aware of the diagnostic possibilities based on examination and imaging of a hand tumor ; however, surgical excision with histologic examination is required for definitive diagnosis.