• 한국추진공학회지
• /
• 제22권2호
• /
• pp.66-73
• /
• 2018

밀폐용기 내 Zirconium/Potassium Perchlorate의 연소를 수치적 모델링을 통해 전산해석을 수행하였다. 5차 WENO 공간차분법과 improved delayed detached eddy (IDDES) 난류모델을 사용하여 충격파가 동반되는 내부 유동구조를 모사하였고, 라그랑지안 연소모델을 통해 화약 입자를 계산하였다. 옆면 중앙에 센서가 설치된 원통형 밀폐용기 내부 유동분석을 통해 압력 진동이 발생하는 원인을 규명하였다. 또한 센서 다이어프램 깊이 변화에 따라 측정되는 압력 데이터를 실험값과 비교분석 하였다. 그 결과 센서 탭의 깊이가 약 2.36 mm 이상으로 커지면 유동속도가 아음속으로 감쇠하고 복잡한 eddy가 발생하여 측정값에 큰 불규칙성을 야기하는 현상을 관측하였다.

• 설비공학논문집
• /
• 제20권5호
• /
• pp.304-313
• /
• 2008

This paper investigates the indoor-air-quality (IAQ) characteristics of the interior space equipped with system air-conditioner. The behaviors of individual variables such as temperature, humidity and concentration of carbon dioxide ($CO_2$) that influence on IAQ of the interior space were characterized under various cooling conditions by numerical and experimental studies. The numerical analysis predicting the temperature behavior of the interior space was conducted, and its results showed a good agreement with the experimental ones. The $CO_2$ concentration and humidity were measured and their time dependent behaviors were monitored and analyzed. From the results, it was found that there existed the differences of the time-dependent behaviors of IAQ variables according to the locations. In addition, it is demonstrated that the large discharge angle of $45^{\circ}$ made the temperature profile more irregular and the high discharge flow of 5.34 m/s produced similar temperature profiles at three different sensing locations. Finally, the humidity of interior space was less sensitive to the changes of the air cooling conditions than the case of temperature and the $CO_2$ concentration increase mainly depended on the number of individuals inside the space.

• 대한조선학회논문집
• /
• 제57권1호
• /
• pp.35-44
• /
• 2020

Propeller cavitation extent, pressure fluctuation induced by cavitation, pressure distribution on propeller blade, total velocity distribution and nominal wake distribution for a MR Taker were computed in both conditions of model test and sea trial using a code STAR-CCM⁺. Then some of the results were compared with model test data at LCT and full-scale measurement (Ahn et al (2014); Kim et al (2014)] in order to confirm the availability of a numerical prediction method and to get the physical insight of local flow around a ship and propeller. The nominal wake distributions computed and measured by LDV velocimeter on the variation of on-coming velocity show the wake contraction characteristics proposed by Hoekstra (1974). The numerical prediction of propeller cavitation extent on a blade angular position and pressure fluctuation level on each location of pressure sensors are very similar with the experimental results.

• 한국철도학회논문집
• /
• 제16권3호
• /
• pp.169-174
• /
• 2013

고성능 EMU 열차의 형상 개선을 통한 공기저항 저감 효과를 알아보기 위하여 3차원정상 Navier-Stokes 방정식과 2방정식 난류 모델을 이용한 전산유체역학을 이용하여 수치해석을 수행하였다. 전산시뮬레이션에는 FLUENTTM ver.13과 Gambit 2.4.6이 사용되었으며, 기본 형상과 유선형으로 개선된 형상에 대하여 계산을 수행하였다. 또한, 터널 내 주행 시의 공기저항 특성을 살펴보기 위하여 개활지에서의 공기저항 계산도 수행하였으며, 차량 별 공기저항 기여도에 대한 분석도 수행되었다. 유선형으로 개선된 형상의 열차는 절편형 전두부와 돌출된 상부 및 하부구조를 가진 기본 형상 열차에 비하여 약 9.8%의 공기저항이 저감된 것을 확인하였으며, 공기저항 저감에 따른 주행저항의 저감은 시속 80km/h에서 약 4%에 이르는 것으로 나타났다.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2006년도 하계학술발표대회 논문집
• /
• pp.387-392
• /
• 2006

The recent on indoor air problem has led to many studies on the methods and effects of ventilation for better indoor air quality. Although natural ventilation is the most effective and energy-saving method in residental housings, the small size of openable window has been a problem in high-rise residential buildings to ventilate only through natural ventilation. Consequently, the installation of mechanical ventilation system has been a requirement in residential buildings, and has caused other problems such as increase of energy consumption and SBS. Hybrid ventilation which uses forces of both natural and mechanical power has been introduced to solve the problem of increase in energy consumption with natural ventilation. In this paper, two types of hybrid ventilation systems in residential building were introduced. One type was with natural ventilation through vent grille in the window, and another type was with natural ventilation through ceiling duct while both types used mechanical ventilation system with the outlets. The indoor temperature distribution and pollution density distribution in summer while operating the ceiling air conditioner were analyzed through CFD simulation. In this paper, the optimal location of diffusers to achieve thermal comfort would be proposed.

• 반도체디스플레이기술학회지
• /
• 제18권4호
• /
• pp.69-74
• /
• 2019

The aim of this work is to investigate the effect of the microtip length in a slot-die head on coating of a fine poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) stripe. To this end, we have employed a meniscus guide with a 150-㎛-wide microtip and performed roll-to-roll slot-die coatings by varying its length between 500 ㎛ and 50 ㎛. When the microtip length is 150 ㎛ or shorter, we have observed three unexpected phenomena; 1) though the solution spreads much wider than the microtip width, yet the coated stripe width is almost the same as the microtip width, 2) the stripe width decreases, but the stripe thickness is rather increased with increasing coating speed at a fixed flow rate, 3) we obtain stripes much narrower than the microtip width at high coating speeds. It is due to the fact that 1) the meniscus is not well controlled by a short microtip, 2) the main stream of solution from the outlet is very close to the substrate and thus the distributed solution along the head lip merges with the main stream, and 3) the solution is not spread over the entire microtip end at high coating speeds, causing a tiny wobble in the meniscus. Using the 150-㎛-wide and 250-㎛-long microtip, we have fabricated 153-㎛-wide and 94-nm-thick PEDOT:PSS stripe at the maximum coating speed of 13 mm/s. To demonstrate its applicability in solution-processable organic light-emitting diodes (OLEDs), we have also fabricated an OLED device with the fine PEDOT:PSS stripe and obtained strong light emission from it.

• 한국산업융합학회 논문집
• /
• 제24권6_2호
• /
• pp.801-808
• /
• 2021

In this paper, a numerical analysis was conducted on the effect of the flow control valve of a oscillation water column(OWC) type wave power generator turbine. The OWC wave power turbine operates with compressed air in the air chamber according to the change of wave height. When the wave height changes rapidly, a flow control valve is required due to overload of the turbine and reduced efficiency. Therefore, in this paper, a flow control valve with an opening angle of 60 degrees was installed in the front of the turbine, and the pressure drop, torque, and overall performance were calculated according to the change of turbine RPM and flow rate of turbine inlet. In conclusion, the flow control valve with an opening angle of 60 degrees affects when the turbine rotates at low rotation and the inlet flow rate is large. But it does not have a significant effect on overall turbine performance and it is necessary to find the optimal angle in the future works.

• Tribology and Lubricants
• /
• 제34권6호
• /
• pp.247-253
• /
• 2018

Temperature rise due to viscous shear of the lubricating oil generates hydrodynamic pressure, even if the lubricating surfaces are parallel. This effect, known as the thermal wedge effect, varies significantly with film-temperature boundary conditions. The bearing conducts a part of the heat generated; hence, the oil temperature varies with the thermal conductivity of the bearing. In this study, we analyze the effect of thermal conductivity on the thermohydrodynamic (THD) lubrication of parallel slider bearings. We numerically analyze the continuity equation, Navier-Stokes equation, energy equation including the temperature-viscosity and temperature-density relations for lubricants, and the heat conduction equation for bearing by creating a 2D model of the micro-bearing using the commercial computational fluid dynamics (CFD) code FLUENT. We then compare the variation in temperature, viscosity, and pressure distributions with the thermal conductivity. The results demonstrate that the thermal conductivity has a significant influence on THD lubrication characteristics of parallel slider bearings. The lower the thermal conductivity, the greater the pressure generation due to the thermal wedge effect resulting in a higher load-carrying capacity and smaller frictional force. The present results can function as the basic data for optimum bearing design; however, the applicability requires further studies on various operating conditions.

• 청정기술
• /
• 제24권4호
• /
• pp.301-306
• /
• 2018

최근 미세먼지의 증가로 인해 디젤 자동차로부터 발생되는 PM에 대한 규제가 강화되고 있다. 디젤 자동차의 배기가스를 제거하는 후처리 장치인 매연여과장치(diesel particulate filter, DPF)에 대한 관심이 급증하고 있다. 따라서 DPF 효율 향상의 하나로 DPF 내의 압력강하를 줄여서 필터 및 재생(Regeneration)의 효율을 증가시키고 있다. 본 연구에서는 ANSYS FLUENT를 이용하여 5.66" SiC와 Cordierite DPF의 셀 밀도, 채널 형상, 벽두께, 입 출구 채널 비에 따른 압력강하 영향을 시뮬레이션했다. 실험결과로서 200 CPSI보다 300 CPSI에서 압력강하가 작게 나타났으며, Anisotropy과 O/S 셀이 Isotropy보다 약 1,301 Pa 작은 압력강하를 나타냈다. 공극률은 10% 증가할 때 마다 압력강하가 약 300 Pa씩 작아졌고, 벽 두께에 따른 영향은 0.05 mm 두꺼워질수록 약 500 Pa 씩 커지는 경향을 나타냈다.

• 한국해양공학회지
• /
• 제33권4호
• /
• pp.322-329
• /
• 2019

The magnitude of the roll motion of a floating structure depends on the roll damping acting on the body. In other words, the roll damping of a floating structure must be accurately obtained in order to precisely evaluate the roll motion. Various methods are used to evaluate the roll damping of a floating structure, such as the linear potential theory, computational fluid dynamics (CFD), and model tests. However, it is difficult to evaluate the roll motion of a floating structure with appendages such as a bilge keel and riser slot due to the limitation of ignoring the viscous effects in the linear potential theory. Among these methods, a model test based on a free decay test and harmonic excited roll motion (HERM) is known to be the most reliable method to estimate the roll damping of the floating structures. In this study, model tests using free decay and HERM techniques were performed in the Ocean Engineering Basin (OEB) of KRISO with various types of midship sections. The roll damping results were estimated based on post-processing methods using both techniques, and the roll damping results were compared.