• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.5
• /
• pp.9-15
• /
• 1999

A digital CDI(Capacitive Discharge Ignition) system on small two stroke motorcycle engine was developed in this paper, This CDI system with microprocessor as its main part has more flexible spark timing than the conventional CDI system because of its programmable characteristics. The principle of this digital CDI system and the design methods of hardware and software were presented in this paper, Two stroke small engine was tested to investigate the performance of digital CDI system And also this system was investigated to optimize the engine performance. Also comparison between conventional CDI can provide better spark timing variation than the conventional system. The part and full load test results show that the engine power was increased about 10-20% and fuel consumption was decreased about 10-20% simultaneously. Furthermore, this digital CDI system has simple structure, low cost and very little modification are required. It is a promising technology to substitute for the widely used conventional CDI system.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.31 no.11
• /
• pp.146-154
• /
• 1982

This paper proposes a new circuit for the CDI system to have a constant ignition power at the engine speed range of 500 to 7500 rpm and the battery voltage range of 12 to 16 volts in the 4-cylinder automobile. The proposed CDI system has a closed-loop with a PWM DC-DC converter controlled by the error signal between capacitor voltage and reference voltage. In order to decrease the capacitor charging time, the primary winding of ignition coil is made to be shorted during capacitor charging. An experimental suystem is fabricated and the results obtained thereof are found to be satisfactory.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.6
• /
• pp.215-221
• /
• 1997

The ability of the engine starting performance of conventional ignition system being currently used in automobile gasoline engine is investigated, and the method of improving is discussed and experimented. The conventional ignition system cannot obtain high ignited voltage because its current is limited by decreasing of terminal voltage of battery at starting the engine also causes irregularity in the starting engine. This paper shows that problem can be improved practically by control of ignition energy properly according to the engine speed, consequently this experimental ignition system can eliminate to remarkable extent the function of the engine starting, and also enhance the performance of the engine at high speed.

• 한국연소학회:학술대회논문집
• /
• 2001.11a
• /
• pp.185-192
• /
• 2001

In this study the characteristics of E-EGR valve developed by UNICK were analyzed and the feasibility of application to vehicles were evaluated. Smart car(3L/100km, cdi version) and engine which is small-displacement size, 0.8-liter, of diesel passenger car developed from Mercedes-Benz were used for this experiment. It was installed a 3-cylinder turbo-charged light duty diesel engine with an electronic EGR valve. After the analysis and comparison of E-EGR valve performance under test benchs, the estimation of vehicle application was executed through the EGR map and CVS-75 test result measured on the chassis dynamometer.

• Journal of Biosystems Engineering
• /
• v.14 no.2
• /
• pp.80-84
• /
• 1989

In order to improve the combustion efficiency of the agricultural engine, an ignition timing control system was developed and tested. The control system was composed of the CDI ignition circuit, the microcomputer and the interfacing devices. In this study, the simplicity of the control system and the flexibility of the control strategy were emphasized for the precision, the applicability and the economical efficiency. The hardware was consisted in almost the same compositions as those of the automobile engine. The softwares of the control algorithms were developed to three types depending on the combination of the quasi-adaptive control and the open loop control which had the different spark advance equations according to the input variables such as engine speed, exhaust gas temperature and brake torque. The test results were summarized as follows: 1. By using the computer control system, the fuel consumption efficiency could be improved and the fuel consumption could be reduced by 0 to 57% compared to that of the fixed spark advance system. 2. The fuel consumption of the control mode with the quasi-adaptive algorithm was reduced by average 0.8% compared to that of the control mode without quasi-adaptive algorithm. 3. It was found that the control mode with the quasi-adaptive algorithm adopting single input of engine speed had most applicability and economical efficiency among three types of the control algorithms.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.6
• /
• pp.13-20
• /
• 2005

The most typical fuel control devices of motorcycle engines have carburetors, they are simple in structure and reliable in work. Most of the motorcycle engines have used carburetors in the fuel system, but the fuel economy and the emissions of those engines are bad when we compared with automobile engines. According to stricter emission regulations and higher requirements for fuel economy, the application of the carburetor on the motorcycle engines would be limited. In this paper, we studied about the ECU of motorcycle engine controled by indirect method. A new engine system was designed and experiments were carried out. The experimental results for both carburetor type and ECU type were compared. Maximum torque of $1.053kg{\cdot}m$ at 6500rpm was measured. The engine torque controled using ECU was increased by $10\%$ compared with the carburetor type.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.353-358
• /
• 2000

To achieve the requirement for high fuel economy and low emissions, the research for GDI engines is recently very brisk in the whole world. This study was performed to measure distribution of average particle size in non-evaporating spray. The 2-D fluorescence/scattering images of fuel spray were captured simultaneously by visualization system composed of a laser sheet, a doubling prism, optical filters, and an ICCD camera. Using the ratio of the two light intensities, particle size distribution was obtained. The SMD measured by fluorescence/scattering technique was compared with it obtained by PDA. The experimental results show that the spray structure of GDI injector and temporal SMD distribution.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.6
• /
• pp.183-191
• /
• 1997

For the improvement of ignitability we need ignition energy and its discharge characteristics which are suitable for a part distribution of the mixture density around the ignition spark plug and the flow characteristics of the mixture in the combustion. Especially, for the solving of the instability of initial ignition and lean ignitability limit in the case of lean-burn combustion, the more powerful ignition energy is required. The conclusions from the observation can be summarized as follows: 1) The ignitability limit for HIS expands wider and the combustion is more stable than for CDI. 2) The combustion duration and ignition timing depend upon the distribution of local mixture density in the vicinity of ignition spark plug.

• Journal of Biosystems Engineering
• /
• v.12 no.1
• /
• pp.45-52
• /
• 1987

In order to improve the thermal efficiency of an internal combustion engine, various ignition timing control systems were examined and the best one was chosen. The parts used for the systems were a microcomputer system with DAS, 8 bit output port (D-FLIP FLOP), three types of isolation circuit, two types of ignition timing pulse generator, three types of switching circuit and two types of high voltage ignition circuit. Most systems did not operate well due to the effects of electromagnetic waves and surge currents occurring when the ignition began or ended with resulting high voltage. The best ignition timing control system was found to be the combination of (microcomputer system)-(ignition timing pulse generator using step motor position control pick-up)-(switching circuit using TR logic)-(high voltage ignition circuit using CDI).