• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1996.03a
• /
• pp.41-46
• /
• 1996

In this study, unsintered and pre-sintered low purity alumina ceramics were machined with various tools to clarify the machinability, optimum tool materials and optimum cutting conditions. The main conclusions obtained were as follows. (1)In the case of dry cutting, the sintered diamond and natural diamond tools exhibit better performance in machining of the ceramic pre-sintered at lower temperature, and the tool lives of both tools in machining the ceramics pre-sintered at high temperature becomes extremely short. (2)The performance of CBN tool becomes better in dry machining of the ceramics pre-sintered at higher temperature. (3)When the pre-sintered ceramics were wet machined with sintered diamond, the tool life becomes considerably long, and higher cutting speed can be used than in the case of the CBN and ceramic tools, the tool lives becomes shorter at wet cutting than at dry cutting, especially exhibiting extremely short tool life in wet cutting with ceramic tool.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.315-320
• /
• 2001

Ultra-abrasives such as diamond and CBN have used to maintain accuracy and form deviation for superalloy etc. This study contains the dry cylindrical grinding of metals with Vitrified-bond CBN wheel and Resinoid-bond CBN wheel. For various condition of grinding speed, workpiece speed, grinding depth and feed speed of table, the grinding resistance, the surface roughness, and material removal are measured and discussed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.363-366
• /
• 2003

The hard turning is a turning operation performed in high strength alloy steels (HRC>30) in order to reach surface roughness close to those obtained in grinding. This is possible because of availability of improved tool materials (polycrystalline cubic boron nitride. PCBN), ad more rigid machine tools. According to many previous work of hard turning mechanism, the maximum temperature of cutting can be raised up to 100$0^{\circ}C$. As the heat generation rate is very high, the thermal displacement of tool holder cannot be negligible. Therefore, the aim of this paper is to analyze effects of high heat generation at CBN tool tip to the thermal displacement of a tool holder in hard turning and finally geometric accuracy. The thermal behavior of a CBN tool holder is investigated by numerical simulation and experiment, and the result shows thermal elongation of microns order is possible during hard turning process.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.2 s.191
• /
• pp.33-40
• /
• 2007

In this study, presintered and full sintered low purity alumina ceramics were machined with various tools to clarify the effect of cutting fluid in machinability. The main conclusions obtained were as follows. When the presintered ceramics were wet machined with sintered diamond tool, the tool wear becomes extremely large, and higher cutting speed can be used than in the case of full sintered ceramics. The productivity of wet cutting with the sintered diamond tool is much higher than that of dry cutting. In the case of the CBN and ceramic tools, the tool wear were smaller at wet cutting than at dry cutting, especially exhibiting considerably larger grooved tool wear in wet cutting with ceramic tool.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.5
• /
• pp.8-12
• /
• 2012

Recently, a wide range of industrial production area has a competitive advantage through cost reduction. Moreover with the development of industrial technology, base material and cutting tool help the machining technology. But most of the machining enterprises have not hold the R&D facilities and human resources. This mainly disturbs the industrial development and th increase of production efficiency. Especially in the interrupted machining process, it showed different behavior with continuous machining process. So it needs to research and develop the tool life and tool wear mechanism analysis.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1996.10a
• /
• pp.91-95
• /
• 1996

One must observe abrasive grain of grinding wheel and know their behaviors to understand the grinding mechanism. The behaviors of abrasive grain on the wheel surface. such as shapes distributions and changes were studied to make the grinding mechanism clear but the behaviors of abrasive grains on CBN wheel are not known enough. From this paper the working surface of a grinding wheel is observed by photography in which a picture of a wheel surface is taken by the camera through the microscope on the grinding machine and analyzed with the computer.

• Journal of the Korean Society for Precision Engineering
• /
• v.11 no.6
• /
• pp.86-97
• /
• 1994

An experimental investigation is reported on the wear mechanism of CBN cutting tools. The cutting experiments were conducted on a lathe equipped with a tool dynamometer for cutting force measurement. The investigation of wear mechanism was executed by observing the worn tools using tool microscope and scanning electron microscope. Results indicate that the flank wear occurs dominantly by abrasive wear mode and the crater wear by adhesive wear mode. The results also indicate that the width of flank wear is closely related with the passive component of cutting force.

• Journal of the Korean Society for Heat Treatment
• /
• v.7 no.3
• /
• pp.199-205
• /
• 1994

The fracture characteristics and tool life of ceramics and WC, CBN cutting tool when turning heat treated steel STD11($H_RC$ 60) were investigated experimentally to clarify the machinability and optimum tool materials in cutting of difficult-to-cut material with high hardness. Forthermore, the behaviors of the tool wear and failure were examined with regard to cutting force. The hardened steel wore the cutting tool edge rapidily and increased the cutting forces, especially radial force. The tool was worn by the abrasive action. Flank Weat of $Al_2O_3-TiC$ ceramic and WC tool become relatively large and CBN & $Al_2O_3$, ceramic tool had a long life among the tool materials tested. The tool fracture patterns were just like minor cutting wear, flank wear, crater wear, notch wear, chipping. Flank wear rate was accelerated by occurrence of chipping. During the proceeding of machining, it was possible to foresee the catastrophic fracture of tool by abrupt increase of radial force.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.4
• /
• pp.27-35
• /
• 1998

Ni-based heat resisting alloys are commonly used for high temperature applications such as in aircraft engines and gas turbines. In this work, the machinability of Nimonic 263 alloy is investigated with respect to optimum tool type and cutting conditions for both continuous and discontinuous machining as well as weld region. Among the five types of tools tested, K25 tool experienced the least of damage in machining the weld region. Furthermore, despite their superior high temperature hardness, Si-Al-O-N and CBN tools peformed poorly in machining Nimonic 263.

• Korean Journal of Metals and Materials
• /
• v.48 no.7
• /
• pp.651-659
• /
• 2010

When high-speed interrupted cutting is carried out for die and mold steels with high hardness, CBN tools manifested a significantly longer wear life than carbide, ceramic, or cermet tools in an experiment of face milling characteristics. In addition, it was also found that they secured a stable surface roughness within a range of 1.6 S~6.3 S, an acceptable range for precision machining for polished machining parts. And it makes them acceptable in the precision machining field, except in industries where very high machining accuracy is required. In the high hardness interrupted cutting, it was advantageous to perform a negaland treatment and a honning treatment on the tools' cutting edge to extend tool life and surface roughness. Also, severe crater development was found on the sloped face in CBN tools following high-speed machining. This caused the cutting edge to be weakened and damaged, and ultimately resulted in a shorter tool life. Finally, as a result of EDX mapping inspection, Cr component was detected evenly on the entire crater wear area, which can be included only in STD 11.