• 한국기계가공학회지
• /
• 제1권1호
• /
• pp.55-62
• /
• 2002

This investigation reports the grinding characteristics of titanium alloy(Ti-6AI-4V). Grinding experiments were performed at various grinding conditions. The grinding forces were measured to investigate the grindability of titanium alloy with the five different wheels including Green carbide, Alumina, Resin Diamond, Resin CBN and Vitrified CBN. To investigate the grinding characteristics of titanium alloy grinding force, force ratio, specific grinding energy and grinding-ratio were measured. Surface roughness was also measured with tracer and the ground surfaces were observed with SEM Residual stress measurement was conducted on the X-Ray Diffractometer. Force ratio of grinding of titanium alloy was very lower than that of grinding of SKD-11 Surface roughness with Resin Diamond wheel was a little larger and rougher surface than that with other wheels Grinding ratio of titanium alloy was a little lower than that of other materials. Grinding ratio of titanium alloy with Diamond wheel was almost six times larger than that With CBN wheel. As a result of five different wheels, the most excellent wheel in grinding of Titanium alloy was Resin Diamond wheel.

• 한국공작기계학회논문집
• /
• 제11권1호
• /
• pp.26-31
• /
• 2002

In this study an experimental investigation was conducted to find the grinding characteristics of ceramics, STD11 and STS304 materials. The grinding force and the microscopic observation of the workpieces were obtained in surface grinding. Grinding characteristics of ceramics were inspected through the microscopic examination the cutting force, and the surface roughness. It has been found that the finding force of ceramics is relatively low as compared to that of steels and that CBN wheel has an excellent performance. The surface roughness was measured according to the feedrate and the depth of out.

• 한국생산제조학회지
• /
• 제23권1호
• /
• pp.69-74
• /
• 2014

An OrthoMTA compacter is made by machining a Ni-Ti alloy wire using tapered helix creep-feed grinding machines. This aim of this study is to find the optimal dressing conditions to sharpen the corner of a cubic boron nitride (CBN) wheel. On the basis of the results of various experiments, it is verified that the most important factors in dressing are the dressing depth and feeding method, whereas the feed rate has less importance for producing a smaller corner R value. The study also finds the optimum dressing depth to reduce the dressing time, a feeding speed and method to stabilize the machining, and the mesh grade for the CBN wheel to make the groove of the compacter deeper.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.870-874
• /
• 1997

Super-abrasives such as diamond and CBN have used to maintain accuracy and form deviation for superalloy etc. This study contains the dry cylindrical grinding of metals with resinoid-bond CBN wheel. For various conditions of grinding speed, workpiece speed, grinding depth and feed speed of table, the grinding resistance and the surface roughness are measured and discussed. The results are as follows.

• 한국정밀공학회지
• /
• 제16권3호통권96호
• /
• pp.103-108
• /
• 1999

A problem in the grinding with a small diametric wheel is the decrease of wheel speed. In order to resolve this problem, an accelerating unit which increases the wheel speed is recommended. In this paper, the accelerating effect of an accelerating unit has been investigated through the side-cut grinding experiments performed with a vitrified bonded CBN wheel in a machining center(MC). The static stiffness, normal force, and machining error were measured in the experiments. As the accelerating unit is attached on the column of machining center, the static stiffness of tool system is largely decreased. But as the wheel speed increased by the accelerating unit, this problem is overcome and machining efficiency is improved. The lesser the quill stiffness was, the higher the accelerating effect became.

• 한국정밀공학회지
• /
• 제16권12호
• /
• pp.54-59
• /
• 1999

High precision internal plunge grinding is difficult because of the decrease in the quill stiffness due to the small diameter of wheel. In this paper, the characteristics of internal plunge grinding were investigated. Grinding experiments were performed at various grinding conditions with vitrified bonded CBN wheels. The grinding period was assumed to be consisted of rough grinding and fine grinding. The classification of grinding was determined int terms of the normal grinding forces and actual depth of cut. The experimental results indicate that the higher depth of cut and infeed speed result in the longer rough grinding time. The maximum normal grinding force was nearly equal to the static force and it decreases exponentially as the grinding continues.

• 한국기계가공학회지
• /
• 제2권2호
• /
• pp.5-13
• /
• 2003

In this study, experiments of high speed grinding had been earned out in a STD11 specimen for evaluating the grindability with designed CBN grinding wheels Ground surfaces were analyzed and evaluated by means of surface Integrities and wheel damages. The surface roughness and 3 dimensional profile had been used for analyzing the micro-surface integrity. The residual stress of the ground surface had been measured by the x-ray diffraction method. Also, the surface state of the ground specimens and the grinding wheels were evaluated by a metallurgical microscope and SEM system after high speed grinding in order to choose the suitable machining conditions.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 춘계학술대회 논문집(한국공작기계학회)
• /
• pp.336-339
• /
• 2001

In this study an experimental investigation was conducted to find the grinding characteristics of ceramics, as compared to STDll and SUS304 materials. The grinding force and the microscopic observation of the workpieces were obtained in surface grinding. It has been found that the grinding force of ceramics is relatively low as compared to that of steels and that CBN wheel has an excellent performance.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.880-883
• /
• 2000

Temperature generated in the workpiece during grinding process can cause thermal damages. Therefore it is important to understand surface temperature generated during grinding process. In this paper, a theoretical and experimental investigation were performed for the grinding temperature. Grinding experiments were performed in machining center using vitrified bonded CBN cup-type wheel. The surface temperature was measured using thermocouple and calculated through a model of the partition of energy between wheel and workpiece. The residual stress and hardness of ground surface were measured. The experimental results indicate that the surface temperature was in good agreement with theoretical ones. Residual stress and hardness of ground surface were more affected by the change of table speed than the depth of cut.

• 한국정밀공학회지
• /
• 제19권2호
• /
• pp.58-64
• /
• 2002

In these days, according to increasing the technical development, the dimension of a product goes up for ultra-precision. For the net shape manufacturing, grinding is a important process that influences directly the accuracy and the integrity of produced products. In this study, an experimental evaluation was carried out. Workpiece materials were used STD11, SUS304, and STB2 in accordance with varing condition of feedrate and depth of cut. From measuring the grinding force and the surface roughness, material characteristics of grinding by using CBN wheel were examined.