• Polymer(Korea)
• /
• v.31 no.1
• /
• pp.8-13
• /
• 2007

To overcome drawbacks of the nylon 6/poly (acrylonitrile-co-butadiene-co-styrene) (ABS) blend, nylon 6 blend with poly (acrylonitrile - co-styrene - co-acrylic rubber) (ASA) which containing poly (butyl acrylate) as a rubber phase in substitute of poly (butadiene) in ABS, was examined. Poly (styrene-co-maleic anhydride) (SMA) containing 25 wt% of maleic anhydride (MA) or poly (styrene- co-acrylo-nitrile-co-maleic anhydride) (SANMA) containing less than 3 wt% MA was used as a compatibilizer to fabricate blends having high impact strength. Changes in the mechanical properties of nylon 6/ASA blend with compatibilizer content were similar with those of nylon 6/ABS blend. Blends haying high impact strength was produced when blends contained more than about 20 wt% rubber. Blends containing SAM or SANMA as a compatibilizer were stayed in a injection molding machine at the molding temperature and afterwards specimens for the examination of the impact strength was prepared. Impact strength of blends containing SMA was decreased with retention time, while that of blends containing SANMA was not changed with retention time.

• Carbon letters
• /
• v.25
• /
• pp.1-13
• /
• 2018

Gold functionalized graphene oxide (GOAu) nanoparticles were reinforced in acrylonitrile-butadiene rubbers (NBR) via solution and melt mixing methods. The synthesized NBR-GOAu nanocomposites have shown significant improvements in their rate of curing, mechanical strength, thermal stability and electrical properties. The homogeneous dispersion of GOAu nanoparticles in NBR has been considered responsible for the enhanced thermal conductivity, thermal stability, and mechanical properties of NBR nanocomposites. In addition, the NBR-GOAu nanocomposites were able to show a decreasing trend in their dielectric constant (${\varepsilon}^{\prime}$) and electrical resistance on straining within a range of 10-70%. The decreasing trend in ${\varepsilon}^{\prime}$ is attributed to the decrease in electrode and interfacial polarization on straining the nanocomposites. The decreasing trend in electrical resistance in the nanocomposites is likely due to the attachment of Au nanoparticles to the surface of GO sheets which act as electrical interconnects. The Au nanoparticles have been proposed to function as ball rollers in-between GO nanosheets to improve their sliding on each other and to improve contacts with neighboring GO nanosheets, especially on straining the nanocomposites. The NBR-GOAu nanocomposites have exhibited piezoelectric gauge factor (${GF_{\varepsilon}}^{\prime}$) of ~0.5, and piezo-resistive gauge factor ($GF_R$) of ~0.9 which clearly indicated that GOAu reinforced NBR nanocomposites are potentially useful in fabrication of structural, high temperature responsive, and stretchable strain-sensitive sensors.

• Elastomers and Composites
• /
• v.43 no.3
• /
• pp.147-156
• /
• 2008

In this work, epoxy/carboxyl-terminated butadiene acrylonitirile (EP/CTBN) composites were prepared by employing a reinforcing filler, silica treated with silane coupling agent in different ratio by dry and wet method. Their curing characteristics, surface free energy, interface morphologies and mechanical properties such as tensile strength and impact resistance were carefully investigated. Differential scanning calorimetry(DSC) results showed that curing temperature was lowered with the increase of silane coupling agent because of the increase of relative curing agent cotent by filling the pores of silica. Wet method was proved to be more effective for lowering curing temperature of EP/CTBN composite. In general, surface free energy and impact resistance were increased with the increase of silane coupling agent in this work. Tensile strength, however, was observed to be decreased at 4 wt% of silane coupling agent. It was found that the dry method was proved to be preferable for pretreatment of silica with coupling agent.

• Polymer(Korea)
• /
• v.28 no.2
• /
• pp.185-193
• /
• 2004

Elastomeric nanocomposites were prepared by employing zinc dimethacrylate into an acrylonitrile-butadiene rubber, and their network structures, mechanical properties, and fracture morphologies were investigated according to the adding methods and contents of zinc dimethacrylate. The total crosslink density increased with increasing the zinc dimethacrylate level, due to increased ionic bonds. Both the tensile strength and tear strength increased with increasing zinc dimethacrylate loadings, and then decreased after reaching a maximum value. It was found that the tear strength and crack resistance were greatly affected by the mixing method of zinc dimethacrylate. The in-situ nanocomposites, where zinc dimethacrylate particles were formed by the reaction of zinc oxide and methacrylic acid, showed much improved tear strength and crack resistance compared to those of the nanocomposites based on the direct mixing of zinc dimetacrylate powders. This was because of the finer zinc dimethacrylate particles and improved dispersion of the in-situ nanocomposites.

• Applied Chemistry for Engineering
• /
• v.4 no.2
• /
• pp.284-290
• /
• 1993

The soap-free emulsion polymerization was carried out for Styrene/Butadiene system with Acrylonitrile as hydrophilic comonomer and KPS as initiator. Under the condition of below 50% conversion, the dependence of Rp on $[AN]^n$ and $[KPS]^n$ was found to be n=1.617-1.050 and n=0.83-0.96 for [AN] and [KPS], respectively. The effect of $[AN]^n$ and $[KPS]^n$ on particle number density (Np) was determined to be n=1.533 and n=0.733, respectively. The highest conversion was obtained under the conditions of pH=5 and ratio of total monomer (g) to water (g)=0.5. The mechanical properties of SBR obtained in this experiment were shown to be inferior to commercial SBR in terms of tensile strength, 300% modulus and elongation. It was found that cure rate of SBR prepared in this experiment was faster than that of commercial SBR.

• Elastomers and Composites
• /
• v.22 no.3
• /
• pp.195-203
• /
• 1987

In this study, as one of the developing ways of the functional elastomer, improvement of the functionality of CB-BR was attempted through moisture curing reaction. The curing reaction of CB-BR was determined with an use of 3-aminopropyltriethoxysilane(APS) as a crosslinking agent, also a solution reaction with an active chlorine of CB-BR was elucidated by using a reaction kinetics theory and a study of physical property was made through moisture curing on the compound of 3-aminopropyltriethoxysilane and CB-BR The results of this study obtained are as follows : 1) CB-BR reacted easily with APS in the liquid state and the reaction rate coefficient and activation energy were as follows : 2) Optimum pressure condition of moisture cured elastomer(CB-BR+APS) was 20 minutes at $150^{\circ}C$, and the crosslinked elastomer was close to the theoretical value (q=1) for Flory's equation($\frac{\alpha}{\alpha-1}=q{\nu}RT$)

• Elastomers and Composites
• /
• v.38 no.2
• /
• pp.139-146
• /
• 2003

In this work, the influence of ozone treatment on surface properties of carbon black is investigated in terms of X-ray photoelectron spectroscopy (XPS) and contact angles. And their mechanical interfacial properties of the carbon black/acrylonitrile butadiene rubber (NBR) compounds are studied by the crosslink density and composite tearing energy ($G_{IIIC}$). As a result, it is found that the increasing of the ozone concentration leads to an increase of the introduction rate of oxygen-containing functional groups onto carbon black surfaces and to an increase of the surface free energy, resulting in improving both crosslink density and tearing energy ($G_{IIIC}$) of the compounds. The results can be explained by the fact that the oxygen-containing functional groups of carbon black surfaces make an increase of the degree of adhesion at interfaces between carbon blacks and rubber matrix.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.12
• /
• pp.4028-4034
• /
• 2012

Tris(2-phenylphenoxo)aluminum ($(2-PhC_6H_4O)_3Al$) exists as a dimeric form in toluene. When toluene-insoluble anhydrous cobalt acetate is treated with tris(2-phenylphenoxo)aluminum in toluene, the toluene-soluble adduct $(2-PhC_6H_4O)_3Al{\cdot}Co(OAc)_2$ is formed. The 2-phenylphenoxo ligand in the adduct can be replaced with another aryloxo ligand to give (aryloxo)$(2-PhC_6H_4O)_2Al{\cdot}Co(OAc)_2$ (aryloxo = 2-methylphenoxo, 2-isopropylphenoxo, 4-methylphenoxo, 4-isopropylphenoxo, or 4-tert-butylphenoxo). These complexes are active for butadiene polymerization without gel formation when activated with an equivalent amount of $(2-PhC_6H_4O)AlEt_2$ for 2 h. The highest activity, 175 kg/mol-Co (turnover number, 3200) was achieved with $(2-PhC_6H_4O)_3Al{\cdot}Co(OAc)_2$ at $65^{\circ}C$ for 2 h. The microstructure of the polymer chains is mostly trans-1,4-configuration (70-75%) with the remaining being 1,2-vinyl. The cis-1,4-configuration observed by IR is minimal (1-5%). By replacing the 2-phenylpheoxo with a 4-alkylphenoxo ligand, the amount of 1,4-configuration slightly increases, resulting in increase in the endothermic melting signal at $-30{\sim}50^{\circ}C$ in the DSC curve. The molecular weights of the polymers are high ($M_n$: 300000~800000) with a fairly narrow molecular weight distribution ($M_w/M_n$, 2.0-2.7).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.9
• /
• pp.6019-6026
• /
• 2015

In this study, we have tried to use 3D-printing technology, which is very useful for small amount production and individual personalization manufacturing to produce a cast customized by individual. To do this, we have made casts by the 3D printer in the method of fused deposition modeling technique using ABS(acrylonitrile butadiene styrene) resin which is thermoplastic plastics. The computed tomography of human hand part was used as the modeling of the cast and it was designed to circulate air well. As a result, an individual personalized cast that fitted well with the model part was produced. In addition, we could get more excellent radiography from the cast than the existing cast. In conclusion, this study of 3D-printing could be used as basic data when a similar designed structure in fused deposition modeling technique by ABS resin is printed out.

• Polymer(Korea)
• /
• v.31 no.4
• /
• pp.283-288
• /
• 2007

Polymer blends containing poly(acrylonitrile-butadiene-styrene) (ABS) and polycarbonate(PC) (70/30, wt%) with compatibilizer were prepared using twin screw extruder. Compatibilizers were prepared by reactive extrusion with the ABS, maleic anhydride(MAH) and dicumyl peroxide(DCP) using twin screw extruder In the ABS/PC (70/30) blends, tensile strength did not change significantly, but increased from 52.25 to 55.03 MPa when the ABS-g-MAH was added in the amount of 5 phr. From the results of rheological properties, storage modulus of the ABS/PC/ABS-g-MAH blends at low frequencies showed lager value than that of the ABS/PC(70/30) blend. From the results of the morphological properties of the ABS/PC(70/30) blend, it was observed that the drop size of the PC ranged from 1.2 to $1.5\;{\mu}m$ and did not change significantly with the addition of the ABS-g-MAH($1{\sim}10\;phr$). From the results of the storage modulus, complex viscosity, and tensile strength of the ABS/PC (70/30) blends, it is found that the ABS-g-MAH is an effective compatibilizer in the ABS/PC (70/30) blends when the ABS-g-MAH is added in the amount of 5 phr.