• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.515-520
• /
• 1998

In this paper, we propose a new fault tolerant architecture for high availability systems, where for module internal operations both processor modules perform the same tasks at the same time independently of each other while for module external operations both processor modules act actively. That is, operations of synchronization between dual processor modules except clock synchronization are requested only when module external operations are executed. The architecture can not only improve system availability by reducing system reintegration time but also reduce performance degradation problem due to frequent synchronization between dual processor modules. The clock unit consists of a clock generator and a clock synchronization circuit. This supplies a stable clock signal under clock unit disorder of any processor module or rapid clock signal variation. And this architecture achieves system availability and data credibility by designing as symmetrical form.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.11
• /
• pp.1004-1011
• /
• 2016

In this paper, we suggested the methodology of analyzing and reconstructing of measured electromagnetic emanations from the Micro Controller Unit(MCU) chip of Universal Serial Bus(USB) keyboard. By analyzing electromagnetic emanations, entered information is found at keystroke and furthermore, information security problems such as personal information leakage and eavesdropping can be arisen. USB keyboards make the radiated signal according to the signal transmission mechanism. Electromagnetic emanations were measured by log periodic antenna and wideband receiver and were analyzed by signal processing algorithm.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.8 no.2
• /
• pp.69-78
• /
• 2013

As vehicles become more intelligent for safety and convenience of drivers, in-vehicle networking systems such as controller are network (CAN) have been widely used due to increasing number of electronic control unit (ECU). Recently, FlexRay was developed to replace CAN protocol in chassis networking systems, to remedy the shortage of transmission capacity and unsatisfactory real-time transmission delay of conventional CAN. However, it is difficult for vehicle network designers to calculate platform configuration registers (PCR) and determine a base cycle or slot length of FlexRay. To assist vehicle network designers for designing FlexRay cluster, this paper presents automatic field bus exchange format (FIBEX) generation algorithm from CANdb information, which is de-facto standard database format for CAN. To design this program, structures of FIBEX, CANdb and relationship among PCR variables are analyzed.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.9
• /
• pp.855-860
• /
• 2016

This study describes the design and implementation of digital Payload power supply. We materialized the interface of the PLDIU and power supply of a satellite bus, and minimized the potential for the occurrence of such erroneous operation circuit ESD through the WCA of the space environment. We designed a reliable power supply through simulation for a TID according to the vibration generated during the launch and space radiation environment, and found no problem in the function and performance through the test space environment after production.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.3
• /
• pp.437-442
• /
• 2021

This study describes the design and implementation of power supply of dehop/rehop transponder of EQM(Engineering Qualification Model). We materialized the interface of the PLDIU and power supply of a satellite bus, and minimized the potential for the occurrence of such erroneous operation circuit ESD through the WCA of the space environment. We designed a reliable power supply through simulation for TID about space radiation and simulation of the vibration generated during it launched, and we confirmed that it satisfies the environmental test specification through the test space environment after production.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.6 s.336
• /
• pp.67-74
• /
• 2005

Crypto-systems have difficulties in designing hardware due to the various standards. We propose a programmable and configurable architecture for cryptography coprocessors to accommodate various crypto-systems. The proposed architecture has a 32 bit I/O interface and internal bus width, and consists of a programmable finite field arithmetic unit, an input/output unit, a register file, and a control unit. The crypto-system is determined by the micro-codes in memory of the control unit, and is configured by programming the micro-codes. The coprocessor has a modular structure so that the arithmetic unit can be replaced if a substitute has an appropriate 32 bit I/O interface. It can be used in many crypto-systems by re-programming the micro-codes for corresponding crypto-system or by replacing operation units. We implement an elliptic curve crypto-processor using the proposed architecture and compare it with other crypto-processors

• Journal of Power Electronics
• /
• v.14 no.4
• /
• pp.733-741
• /
• 2014

The integration of photovoltaic (PV) energy sources into DC grid has gained considerable attention because of its enhanced conversion efficiency with reduced number of power conversion stages. During the integration process, a local control unit is normally included with every power conversion stage of the PV source to accomplish the process of maximum power point tracking. A centralized monitoring and supervisory control unit is required for monitoring, power management, and protection of the entire system. Therefore, we propose a field-programmable gate array (FPGA) based centralized control unit that integrates all local controllers with the centralized monitoring unit. The main focus of this study is on the process of integrating many local control units into a single central unit. In this paper, we present design and optimization procedures for the hardware implementation of FPGA architecture. Furthermore, we propose a transient analysis and control design methodology with consideration of the nonlinear characteristics of the PV source. Hardware experiment results verify the efficiency of the central control unit and controller design.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.22 no.5
• /
• pp.1057-1068
• /
• 2012

According to advance on vehicle technology, many kinds of ECU(Electronic Control Unit) are equipped inside the vehicle. In-vehicle communication among ECUs is performed through CAN(Controller Area Networks). CAN have high reliability. However, it has many vulnerabilities because there is not any security mechanism for CAN. Recently, many papers proposed attacks of in-vehicle communication by using these vulnerabilities. In this paper, we propose an wireless attack model using a mobile radio communication network. We propose a secure authentication mechanism for in-vehicle network communication that assure confidentiality and integrity of data packets and also protect in-vehicle communication from the replay attack.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1714-1719
• /
• 2003

Antilock Brake System (ABS) is indispensable safety equipment for vehicles today. In order to develop new ABS ECU suitable for pneumatic brake system of a bus, a Hardware In-the-Loop Simulation (HILS) System was developed. In this HILS, the pneumatic brake system of a bus and antilock brake component were used as hardware. For the computer simulation, the 14-Degree of Freedom (DOF) bus dynamic model was constructed using the Matlab/Simulink software package. This model was compiled and downloaded in the simulation board, where the Power PC processor was used for real-time simulation. Additional commercial package, the ControlDesk was used to monitor the dynamic simulation results and physical signal values. This paper will focus on the procedure and results of evaluating the ECU in the HILS simulation. Two representative cases, wet basalt road and $split-{\mu}$ road, were used to simulate real road conditions. At each simulated road, the vehicle was driven and stopped under the help of the developed ECU. In each simulation, the dynamical behavior of the vehicle was monitored. After enough tests in the laboratory using HILS, the parameter-tuned ECU was equipped in a real bus, which was driven and stopped in the real test field in Korea. And finally, the experiment results of ABS equipped vehicle's dynamic behavior both in HILS test and in test fields were compared.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.183-183
• /
• 2007

Bimodal Tram is a new public transportation system combined subway with bus and consists of variable electric equipment to accomplish the comfortness, reliability, safety and so on. One of them is VCU(Vehicle Control Unit) for Performing driver's cmmand and monitoring the state of other equipment. To lessen the wiring and the interference of outer electromagnetic noises is very important things for bimodal tram with complicated configuration of electric equipments. This paper has investigated the application of CAN(Controller Area Network) communication method for VCU which has display, central unit and several nodes that are connected with other electric equipments(HVAC, door controller etc). We designed and manufactured the prototype of VCU which eventually will be installed on bimodal tram being developed in KRRI at present.