• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.35 no.5
• /
• pp.169-179
• /
• 2019

During the initial design stage of apartment complex, the photovoltaic(PV) system has been considered as an alternative of renewable energy system and planned to install at the rooftop floor level in general. The electric power generation characteristics can be influenced by the block layout, building orientation and roof top structure because of azimuth angle, tilt angle, and partial shading. This study aims to investigate power generation characteristics of photovoltaic system in apartment buildings by considering the partial shading conditions due to the block layout, building orientation and roof-top structures. For the photovoltaic module arrangement planning in rooftop floor level, shading areas were firstly analyzed due to the adjacent building structure. And the annual and seasonal power generation of PV system were analyzed through the PVsyst simulation results. The results show that shading period at the roof top surface can be increased due to the parapet and water tank. Initial design power capacity can be decreased by considering the daily insolation period and distance between PV modules through the shading simulation. As the number of PV modules decreases, the annual power generation can be decreased. However annual power generation per unit area of PV modules can be increased and performance ratio can be increased above 80%. Also the power generation of PV system can be critically affected by building orientation and the performance ratio can be drastically decreased in east-oriented buildings due to the shading problems caused by adjacent structures at roof top level such as parapet and water tank.

• Journal of the Korean housing association
• /
• v.21 no.4
• /
• pp.99-109
• /
• 2010

The purpose of this study is to provide basic data needed for planning apartment community spaces in order to vitalize rental apartments. Indoor community spaces of 12 rental apartments in Seoul and Kyunggi were examined. The results are as follows. First, the layout types of indoor community spaces in rental apartment complexes were found out to be mostly the building type planned in the piloties of the apartment, or the singular type placed in a singular building. Depending on the layout type, the spaces were mostly concentrated at the outskirt of the complex or the in-between space of the main building, thus lowering their recognition. Thereby, they were not satisfactory for utilization of the spaces and association of residents. Second, Indoor community space legal establishment standard and square measure did not reflect resident's feature except elderly spaces, and there was problem in activation of space. Third, as for the spatial planning of indoor community space, although each space was categorized by the users' age, the furniture and appliance planning considering users was not satisfactory. The area calculation by the type of space did not reflect the users' characteristics, thus causing problems in using the facilities. Fourth, as for the management and programs of the indoor community space, spaces were managed after categorized by the major user classes such as children, seniors, and adolescents. Depending on eagerness of program managers of each apartment complex, the level of program management varied. The survey results showed that, in most cases, almost no programs were used or merely basic management and programs were being provided.

• Journal of KIBIM
• /
• v.10 no.3
• /
• pp.22-32
• /
• 2020

Apartment building site planning is one of time consuming and labor-intensive tasks in architectural design field, due to its complexity in zoning regulations, building codes, local restrictions, and site-specific conditions. In other words, the process can be seen as a very complicated mathematical function with layers of variables and parameters, which ironically can be automated using computational methods on parametric tools. In this paper, a practical method of automating site planning of an apartment complex has been proposed by utilizing parametric approaches in Rhino 3D and Grasshopper. Two primary parameters, building heights and positions, determine the efficacy of building layouts under all regulatory standards, thus testing out numerous combinations of the two will produce some successful layout alternatives. For this, equation solver has been used for iterating the parametric model to sort out meaningful results among others. It also has been proven that the proposed process significantly reduced the time in site planning down to less than an hour on most cases, and many successful alternatives could be obtained by using multiple computers. Post evaluation processes such as day light and view shed analysis helped sort out the best performing ones out of functioning alternatives.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2022.11a
• /
• pp.155-156
• /
• 2022

In the process of developing an industrial robot, various simulations should be conducted to evaluate the driving, movement, and performance of the robot. Space and time constraints exist to manufacture existing robots and implement various simulations, and efficiency is reduced due to high costs. To solve this problem, many simulations can be conducted by implementing the same movement and working environment as the real environment in virtual reality using digital twin technology. This study proposes a process for establishing a digital twin model of automated layout robots. Using the digital twin model, it is expected that it will not only evaluate the hardware performance of the robot in the future, but also verify the robot's algorithms such as motion planning and work process, identify and solve potential problems in advance, and prevent problems caused by software.

• Architectural research
• /
• v.1 no.1
• /
• pp.31-40
• /
• 1999

In this age of "Information", many people consider it a deterrent to information flow to provide a hierarchy with private rooms in a modern office layout. There are others, however, who insist that visual and acoustical privacy are more important than any other design factor in achieving higher productivity. The debate may never end, but the partitioned open plan, which is a new form of the vast open plan, has merits of each concept - open and closed layout. Consequently, office design has dramatically shifted to partitioned open planning, with shorter, temporary walls or partitions, originally intended for increasing privacy and diminishing hierarchy, yet still keeping flexibility in spatial organization. The introduction of low-level partitioned spaces in an office layout, however, produces a complicated lighting design problem. Obviously, accurately predicted daylighting performance data are needed not only for daylighting design but for artificial lighting system design. Scale models of 12 sets of unit partitioned spaces are constructed and extensive scale model measurements of both daylight and reflected sunlight have been performed within an artificial sky simulator. The prototype-building interior is modeled with different partition configurations, each of which is modeled using the different envelope geometry and exterior configurations, and then the variations in interior light levels are estimated. The result indicates that partitioned spaces employed in an open plan of modern offices still offer a large potential for daylighting and energy saving as well. Much of the savings may derive from the cumulative effect of reflected sunlight. Optimal design for building envelope geometry and exterior configuration promises additional savings.

• Journal of architectural history
• /
• v.25 no.4
• /
• pp.65-73
• /
• 2016

This paper aimed to identify the units of measuring scale in Hwangnyongsa temple planning with the published excavation survey reports. Hwangyongsa temple site was planned under Silla Capital's urban planning in 6~7C, its full size was $800{\times}800$, and main temple was $400{\times}515$ of Goguryeo's system of measurement. Main hall was located in the center of Hwangnyongsa temple site, and its location could be seen that there was the arrangement of main temple divided into 3 : 2. Building plan measuring units proved to be 351~356mm and 294~ 296mm by analyzing measured data of remains. Lecture hall and Wooden pagoda were rebuilt by using the ancestors' units of measuring scale again and Bell hall was not planned by Tang's system of measurement in middle of 8C. In this respect, it would be important to have a deliberate attitude and lay down stereotypes on research of the units of measuring scale in ancient architecture.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.11 no.1
• /
• pp.39-51
• /
• 2008

These days, one of the issues well discussed is the obstruction or screen of sight to mountain-skyline by buildings. So question is to which heights buildings should be constructed over mountain-skyline and then harmony can be realized between mountain-skyline and building-outline. Based on the mentioned above, this study intends to find out the proper projection- level of buildings over background mountain-skyline when considering the types of mountain-skyline, building-outline and building-layout. The results of this study are first, the proper projection-ratio of buildings over background mountain-skyline can be 0.1 because assessment values on harmony-level are more than 3.0 in almost cases, second, the building-outline influences on the assessment values of harmony-level when the types of mountain-skyline are formed left-high & right-low and right-high & left-low, third, building-layout doesn't influence on the assessment va lues of harmony-level, finally, statistically difference doesn't exist between expert group and non-expert group in the assessment values of harmony-level.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.32 no.3
• /
• pp.76-90
• /
• 2004

The purpose of this study is to extract landscape design elements regulation of the District Unit Plan(DUP) in new town areas, and to find out characteristics in terms of urban design elements in comparison with the psychological and physical aspects. For this purpose, we reviewed urban design elements and design elements in terms of the landscape by DUP and analyzed the activation of landscape on the selected case-area by interviewing experts such as planners, public officials, and professors in the department of urban planning and landscape, as well as the university students. The analysis framework for the case-study consists of 4 components: the section of region, street, building, open space, etc. The new development areas in Daejeon Metropolitan City was chosen as the case study area, because they have been developed by DUP regulations. As a result of this study, we can extract characteristics of landscape. The results indicate that `skyline design',`view corridor design',`landscape design',`street furniture design' and `building design(form, height, color, and elevation)' are the key planning and design factors influencing differences in the landscape preference. This research identifies that there are no detailed planning and design guidelines adopted within the four case study areas in Daejeon for regulating the characteristics of skyline, planting and street furniture while detailed guidelines established for density, building height and site layout. Considering their significant correlation with the level of landscape preference, this study suggests that detailed planning and design guidelines for the characteristics of skyline, rooftop and streetscape should be established in future DUP.

• International conference on construction engineering and project management
• /
• 2013.01a
• /
• pp.1-6
• /
• 2013

Concrete construction requires utilization of many temporary facilities such as formwork, shoring, and scaffolding. Appropriate use of these temporary facilities greatly impacts the quality, cost, schedule, and safety of concrete construction. The current practice in design and planning of temporary facilities is often manual, error-prone, and re-active based on construction site layout, status, and progress in the field. Early design and planning of temporary facilities for concrete construction using Building Information Modeling (BIM) technology offers a potential solution. Although some commercially-available software exists that assists in the generation of temporary facility designs, the construction industry lacks tools that support detailed planning and design of many other temporary facilities. This research presents our early work in automating the design and planning of temporary facilities utilizing BIM. Algorithms were developed to automatically assess geometric conditions of work space to detect required temporary facilities and design them. The proposed methodology was implemented in a test model. By automatically incorporating temporary facilities into BIM, more realistic construction models can be created with less effort and errors. Temporary facilities-loaded models can finally be used for communication, bill of materials, scheduling, etc. and as a benchmark for field installation of temporary formwork, shoring, and scaffolding systems.

• International Journal of High-Rise Buildings
• /
• v.12 no.1
• /
• pp.83-91
• /
• 2023

Under the dual pressure of population growth and land shortage, threedimensional development is the inevitable choice for cities in China. In such a scenario, a mixed-use complex has considerable potential in its realization and research. Based on space syntax and the three-dimensional visibility graph analysis, this paper describes the spatial and functional layout of the Shanghai Super Brand Mall and studies the relationship between spatial visibility and user behaviour through linear regression analysis and correlation analysis. This paper studies three different types of user behaviour, namely, path selection, staying selection, and store selection, and finds that spatial visibility and accessibility have different effects on user behaviour depending on the type and purpose of the activity. This paper reveals the influence of spatial and functional layout on user behaviour and puts forward the corresponding design strategy under the three-dimensional environment.