• Advances in concrete construction
• /
• v.8 no.3
• /
• pp.217-223
• /
• 2019

This paper presents the mechanical and microstructural properties of the geopolymer paste which was developed by utilizing the industrial by-products, rice husk ash (RHA) and ultra-fine slag. Ultra-fine slag particles with average particle size in the range of 4 to 5 microns. RHA is partially replaced with ultra-fine slag at different levels of 0 to 50%. Sodium silicate to sodium hydroxide ratio of 1.0 and alkaline liquid to binder (AL/B) ratio of 0.60 is taken. Setting time, compressive, flexural strengths were studied up to the age of 90 days with different concentrations of NaOH. The microstructure of the hybrid geopolymer paste was studied by performing the SEM, EDS, and XRD on the broken samples. RHA based geopolymer paste blended with ultrafine slag resulted in high compressive and flexural strengths and increased setting times of the paste. Strength increased with the increase in NaOH concentration at all ages. The ultra-small particles of the slag acted as a micro-filler into the paste and enhanced the properties by improving the CASH, NASH, and CSH. The maximum compressive strength of 70MPa was achieved at 30% slag content with 16M NaOH. The results of XRD, SEM, and EDS at 30% replacement of RHA with ultra-fine slag densified the paste microstructure.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.36 no.4
• /
• pp.345-350
• /
• 1991

Rough rice samples of Chucheongbyeo, Bongkwangbyeo and Hwaseongbyeo were collected by the National Agricultural Products Inspection Office. Drying methods of rough rice were sun drying and forced ventilation drying by an oven dryer and temperature of the oven dryer was set to 43, 60, 70, or 8$0^{\circ}C$. Moisture content of samples was reduced from ca. 20% to 15% at the end of drying, and additionally to 12.5 % for the drying at 8$0^{\circ}C$. Characteristics related to rice grain quality, milling recovery, ratio of broken and cracked rices, percentage of germination, and sensory scores of the cooked rices were evaluated. Yielding percentage of brown rice and polished rice remarkably decreased by drying at 8$0^{\circ}C$. Percentages of cracked rice and broken rice were within the criterion of the second grade government brown rice (20%) only in the sun dried and the rices dried at 43$^{\circ}C$, on the basis of damaged rice, opaque kernel rice and colored rice. Broken rice percentage of the polished rice was within the criterion for the standard of government rice (5%) in the sun dried and the rices dried at 43$^{\circ}C$. Germination percentage of rough rice was higher than 80% in sun drying and drying at 43$^{\circ}C$, but remarkably decreased by drying rice at 6$0^{\circ}C$ and over. Sensory palatability of the cooked rice decreased with increase in drying temperature. The present governmental method of judging rough rice on the basis of moisture content and appearance of the rough rice appears to be improved to include the ratio of broken and cracked rices.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.7
• /
• pp.3123-3131
• /
• 2012

The purpose of this study was to evaluate the timing of precocious puberty and the factors inducing precocious puberty in elemental school girls students of low grades. The 1st, 2nd, and 3rd grade 253 elemental girls students from the Goryong province were randomly selected, G and D elemental school. sexual maturation rate was assessed physical examination by the parents. After obtaining an informed consent, a questionnaire was administered to the parents; sexual maturation rate was assessed by self physical examination, eating habits, lifestyle and home background were evaluated to determine the factors that induced precocious puberty. The data were statistically analyzed. We selected 253 girls: The total percentage of the precocious puberty was 26.1%. 7(7.8%) 6-year-old girls, 9 (13.2%) 7-year-old girls, 50 (52.6%) 8-year-old girls were in breast stage 2 and over. The main factors influencing precocious puberty were obesity scale, frequency of eating instant food, TV watching time, stress levels and broken family. A high rating on the obesity scale and high frequency of eating instant food, too much time in front of TV, high stress and broken family indicated advanced stage of puberty. This study show that prevalence ratio of the precocious puberty was 26.1%. The significant influencing factors in advanced puberty were obesity scale and frequency of instant food, TV watching time, high stress and broken family.

• Journal of Environmental Science International
• /
• v.5 no.4
• /
• pp.441-451
• /
• 1996

The surface meteorological and upper layer meteorological observation carried out to investigate influences of sea breeze effect on lower layer atmosphere at Gori nuclear power plant for 29∼30 July, 1996. According to surface meteorological data, the inflow of sea breeze was occurred 11:30 on 29 July, 10:30-on 30 July, respectively, at observation site. And the meteorological tower data showed that wind direction of sea breeze was identified as south-westerly, and wind speed of 58 m was 2 times stronger than that of 10 m. It is notworthy that surface inversion layer which built from the night time to daybreak of next day was not broken off by seab reeze's inflow for daytime, and strong inversion layer observed at 47∼243 m with moderately stable class (F) by URC. It was found that strong stable layer of potential temperature appeared at that layer, maximum relative humidity observed at the bottom of inversion layer and maximum mixing ratio observed in the low of inversion layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.503-506
• /
• 2002

BSCCO 2212 HTS was fabricated by CFP(centrifugal forming process). The powder was initially ground in the mixing ratio of 2:2::1:2 with 10% of SrSO$_4$. The temperature increased up to 1035$^{\circ}C$ and 1200$^{\circ}C$ for melting. The melt was poured into the preheated and rotating copper mould from 200 to 600$^{\circ}C$. The specimen was not broken by thermal impact when the melting temperature was over 1050$^{\circ}C$ and copper mould was preheated over 400$^{\circ}C$ for 30min. A tube type of specimen was annealed at 840$^{\circ}C$ or 860$^{\circ}C$ in oxygen atmosphere for 24hours. Typical microstructure was analyzed in terms of CFP parameters by XRD, SEM, and EDS and also superconducting characteristics were compared.

• Particle and aerosol research
• /
• v.8 no.2
• /
• pp.75-81
• /
• 2012

The strength of lumped cokes can be represented by some index numbers. Although some indexes are suggested, these indexes are not enough to enlighten fracture mechanism. To find essential mechanism, a computational way, discrete element method, is applied to the uniaxial compression test for cylindrical specimen. The cylindrical specimen is a kind of lumped particle mass with parallel bonding that will be broken when the normal stress and shear stress is over a critical value. It is revealed that the primary factors for cokes fracture are parallel spring constant, parallel bond strength, bonding radius and packing ratio the parallel bond strength and radius of the parallel combination the packing density. Especially, parallel spring constant is directly related with elastic constant and yield strength.

• Journal of Biosystems Engineering
• /
• v.32 no.1 s.120
• /
• pp.1-5
• /
• 2007

This study was conducted to find out effects of abnormal kernels of 0 to 30% in brown rice on quality characteristics during milling using friction type test mill. The average hardness values of abnormal and normal brown rice kernels were 6.52 kg$_f$, 8.48 kg$_f$, respectively. According to the increase of abnormal kernels in brown rice, grain temperature, required electrical energy, the broken kernels ratio, and the weight of solid matter on the surface of milled rice were increased due to crush of the abnormal kernels during milling, which proves that abnormal kernels in brown rice should be removed before milling to improve milling characteristics.

• Structural Engineering and Mechanics
• /
• v.55 no.1
• /
• pp.79-92
• /
• 2015

In this study, free vibration analyses of symmetric laminated cantilever and simply supported damaged composite beams are investigated by using finite element method (FEM). Free vibration responses of damaged beams are examined using Euler Bernoulli beam and classical lamination theories. A computer code is developed by using MATLAB software to determine the natural frequencies of a damaged beam. The local damage zone is assumed to be on the surface lamina of the beam by broken fibers after impact. The damaged zone is modeled as a unidirectional discontinuous lamina with $0^{\circ}$ orientations in this study. Fiber volume fraction ($v_f$), fiber aspect ratio ($L_f/d_f$), damage length ($L_D$) and its location (${\lambda}/L$), fiber orientation and stacking sequence parameters effects on natural frequencies are investigated. These parameters are affected the natural frequency values significantly.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2658-2663
• /
• 2008

In the present study, we designed a microfluidic flatform that generates monodisperse droplets with diameters ranging from hundreds of nanometers to several micrometers. To generate fine droplets, T-junction and flow-focusing geometry are integrated into the microfluidic channel. Relatively large aqueous droplets are generated at the upstream T-junction and transported toward the flow-focusing geometry, where each droplet is broken up into the targeted size by the action of viscous stresses. Because the droplet prior to rupture blocks the straight channel that leads to the flow-focusing geometry, it moves very slowly by the pressure difference applied between the advancing and receding regions of the moving droplet. This configuration enables very low flow rate of inner fluid and higher flow rate ratio between inner and outer fluids at the flow-focusing region. It is shown that the present microfluidic device can generate droplets with diameters about 1 micrometer size and standard deviation less than 3%.

• ETRI Journal
• /
• v.29 no.5
• /
• pp.619-632
• /
• 2007

Side channel attacks are a very serious menace to embedded devices with cryptographic applications. To counteract such attacks many randomization techniques have been proposed. One efficient technique in elliptic curve cryptosystems randomizes addition chains with binary signed digit (BSD) representations of the secret key. However, when such countermeasures have been used alone, most of them have been broken by various simple power analysis attacks. In this paper, we consider combinations which can enhance the security of countermeasures using BSD representations by adding additional countermeasures. First, we propose several ways the improved countermeasures based on BSD representations can be attacked. In an actual statistical power analysis attack, the number of samples plays an important role. Therefore, we estimate the number of samples needed in the proposed attack.