• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.5 s.347
• /
• pp.68-76
• /
• 2006

We propose a low noise broadband light source (BLS) and investigate a cost-effective wavelength division multiplexing-passive optical network (WDM-PON) for the convergence of broadcasting and data service. The proposed BLS is used for an injection light of wavelength-locked Fabry-Perot laser diodes (F-P LD) and helps the color-free operation of dense WDM-PON (DWDM-PON). In addition, we apply this BLS to a optical source for overlay of digital broadcasting channel on the WDM-PON.

• Journal of the Optical Society of Korea
• /
• v.15 no.3
• /
• pp.222-226
• /
• 2011

We demonstrated the feasibility of an amplified wavelength-division multiplexed passive optical network (WDM-PON) architecture based on broadband light source (BLS) seeded optical sources and a novel bidirectional reach extender. Our bidirectional reach extender could provide an amplification of both downstream and upstream signals as well as a BLS output for the upstream WDM signal generation. An error-free 1.25 Gb/s signal transmission over a 100-km long single-mode fiber was achieved in a bidirectional WDM-PON using BLS seeded reflective semiconductor optical amplifier (RSOA) sources.

• Journal of the Optical Society of Korea
• /
• v.16 no.2
• /
• pp.101-106
• /
• 2012

We demonstrate a cost effective broadcast signal transmission at 1.25-Gb/s with 100 GHz channel spacing based on a broadband light source (BLS) for a wavelength division multiplexing-passive optical network (WDM-PON). The BLS is implemented by using mutually injected Fabry-Perot laser diodes (MI F-P LDs). The error-free transmission without a forward error correction (FEC) is achieved by its low relative intensity noise (RIN). The number of usable modes is determined by RIN and/or extinction ratio (ER) in the spectrum sliced light output.

• Journal of the Optical Society of Korea
• /
• v.15 no.1
• /
• pp.4-8
• /
• 2011

We have evaluated the performances of bidirectional optical amplifiers which were suited for the cost-effective implementation of amplified bidirectional passive optical networks (PONs). First, we measured the maximum gains of two simple bidirectional optical amplifiers implemented without using any optical components for the suppression of reflected signals. From the results, the maximum gains of two simple bidirectional amplifiers with a broadband light source (BLS) seeded optical source were limited to be 27 dB due to the reflection-induced in-band crosstalk, when the reflectance coefficients were measured to be -33 dB in both directions. Then, we have also implemented a bidirectional optical amplifier with two band splitters for the amplified bidirectional PON where the two different wavelength bands were allocated to the downstream and upstream signals transmission. In our measurement, we confirmed that the maximum gain of bidirectional optical amplifier with two band splitters could be increased to more than 30 dB owing to the efficient suppression of in-band crosstalk.

• Journal of the Optical Society of Korea
• /
• v.18 no.6
• /
• pp.646-649
• /
• 2014

Performances of spectrum-sliced channels are strongly affected by their relative intensity noise (RIN). We use polarization-independent optical modulators (PIOMs) for spectrum-sliced channels to suppress their RIN. The PIOM driven by a high sinusoidal voltage signal evenly redistributes optical frequency components in the spectral domain and reduces the RIN. It can be used at a broadband light source (BLS) output to produce spectrum-sliced channels having lower RIN values. Also, it can be used for each spectrum-sliced channel within each optical network unit (ONU). In our experiment, where 12.5-GHz-spaced spectrum-sliced channels are used in 1-GbE speed, the use of PIOM at the BLS output reduces the bit error rate (BER) of the spectrum-sliced channel by more than an order of magnitude. The use of PIOM within the ONU reduces the BER by approximately 3 orders of magnitude.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.5 s.347
• /
• pp.59-67
• /
• 2006

We demonstrate bidirectional long-reach 35-channel dense wavelength division multiplexing-passive optical network(DWDM-PON) based on wavelength-locked Fabry-Perot laser diodes (F-P LDs). The mode control of F-P LD enhances output power at decreased the required injection power. We show packet-loss-free transmission in all 70 channels at 125 Mb/s per channel line rate through 70 km of single mode fiber without optical amplifier The DWDM-PON can consolidate a metro network into an access network by bypassing the central offices within its reach. The proposed DWDM-PON can accommodate about 80 subscribers with an EDFA-based broadband light source. Further expansion up to 100 subscribers is possible with a semiconductor-based BLS.

• Nuclear Engineering and Technology
• /
• v.52 no.12
• /
• pp.2847-2851
• /
• 2020

A simple water level measurement method based on wavelength division multiplexing (WDM) is proposed and demonstrated. The measurement principle is based on the change of Fresnel reflection occurring at the end facet of the optical fiber tip (OFT). To increase the spatial resolution of water level sensing, a broadband light source (BLS) and an arrayed waveguide grating (AWG) are employed. The OFTs are multiplexed with the dedicated wavelength channels of AWG. By measuring all of the reflection powers reflected at the OFTs with a proposed on-site reflectometer, the water level can be monitored continuously for a fast emergency response. Moreover, it can be implemented easily with the commercially available optical components and devices with the simple configuration.

• Journal of the Optical Society of Korea
• /
• v.18 no.5
• /
• pp.436-441
• /
• 2014

We have demonstrated an amplified wavelength-division multiplexed (WDM) passive optical network (PON) by using broadband light source (BLS) seeded optical sources and chirped fiber Bragg gratings (FBGs) based dispersion compensators. Chirped FBGs located at central office (CO) were fabricated and used as channel-by-channel dispersion compensators in order to mitigate the dispersion-induced distortion of both downstream and upstream signals. Owing to a low insertion loss of chirped FBG based dispersion compensator, the optical signal-to-noise ratio (OSNR) of the downstream signal could be improved to be ~28 dB. Thus, we re-confirmed that an error-free transmission of 1.25 Gb/s signals over a 100 km single-mode fiber (SMF) link could be achieved with a proposed amplified WDM-PON architecture. We have also evaluated the impact of various noises on the system's performance, and found that the low OSNR of the downstream signal would be a main limiting factor on the maximum reach of the proposed amplified WDM-PON architecture. From the measured ~13 dB improvement in OSNR of the downstream signal compared to our previously-proposed dispersion compensating module based scheme, we believe that the proposed architecture can accommodate a reach of longer than 100 km SMF link easily.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.3
• /
• pp.146-152
• /
• 2013

In this paper, we have proposed and experimentally demonstrated an intensity-based self-referencing fiber optic sensor. The proposed fiber optic sensor consists of a broadband light source (BLS), fiber Bragg grating (FBG), tunable Fabry-Perot (F-P) filter, and LabVIEW program. We define the measurement parameter (X) and the calibration parameter (${\beta}$) to determine the transfer function(H) of the self-referencing fiber optic sensor, and the validity of the theoretical analysis is confirmed by experiments. The self-referencing characteristic for the proposed system has been validated by showing that the measurement parameter (X) is invariant for BLS optical power attenuations of 0 dB, 3 dB, and 6 dB. Also, the measured result is irrelevant to the FBGs with different characteristics. This means that the proposed fiber optic sensor offers the flexibility for determining the FBGs needed for implementation. Experimental results for the proposed fiber optic sensor are in good agreement with a theoretical analysis for BLS optical power attenuations and for three FBG pairs with different characteristics. So, the proposed fiber optic sensor has several benefits, including the self-referencing characteristic and the flexibility to determine the FBGs.