• 한국가구학회지
• /
• 제12권1호
• /
• pp.47-55
• /
• 2001

Violin bridge blank cut from maple wood with good quality has typical pattern of the radial direction in the side edge with minimal dispersion. This experimental study was designed and carried out to examine the effect of the physical and macroscopical characteristics on the compressive creep of violin bridge blank which had been imported from European manufacturer. This research arose from the idea that the maple solid wood with heterogeneous wood density and ray direction in the side edge would have uneven rheological property of violin bridge blank which is supposed to be pressed by the tension of strings. Experimentally, the compressive creep of bridge blank became smaller with the higher density of imported maple wood and showed clear density-dependence for the duration of load under the string tension of 5 kgf. Every bridge blank showed the behavior of primary creep stage(stress stabilization) having logarithmic regression creep curve with high correlation coefficient under the designed stress level. Even though the relationship between compressive creep and ray direction on the side edge of bridge was not so clear contrary to expectation, we could conclude that wood density and ray direction should be the quality decisive factors affecting the acoustical characteristics and performance of the bridge, the core member of violin-family bow instruments.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.1713-1718
• /
• 2010

An ultimate strength evaluation of the through plate girder bridge using nonlinear inelastic analysis is presented. In this method, separate member capacity checks after analysis are not required, because the stability and strength of the structural system and its component members can be rigorously treated in analysis. The method captures the inelastic redistribution of internal forces throughout a structural system, and allows an economic use of material for highly indeterminate steel bridges.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.534-537
• /
• 2006

The jacking of cantilever before key segment closure has been introduced to offset the long term forces caused by creep and shrinkage. In this paper, the behavior of structural system with the jacking force in approach bridge of Incheon Bridge was reviewed. The introduction of jacking force effectively offset the long term horizontal forces and allows economic substructure member design.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2001년도 추계 학술발표회 논문집 Proceedings of EESK Conference-Fall 2001
• /
• pp.131-138
• /
• 2001

The purpose of this study is to investigate size effect on inelastic behavior of reinf bridge piers subjected to cyclic load. A computer program, named RCAHEST(Reinforced Co Analysis in Higher Evaluation System Technologr), for the analysis of reinforced concret was used. Material nonlinearity is taken into account by comprising tensile, compressiv models of cracked concrete and a model of reinforcing steel The smeared crack app incorporated. In boundary plane at which each member with different thickness is conne discontinuous deformation due to the abrupt change in their stiffness can be taken into introducing interface element. The effect of number of load reversals with the same d amplitude has been also taken into account to model the reinforcing steel. To determine th on bridge pier inelastic behavior, a 1/4-scale replicate model was also loaded for compar full-scale bridge pier behavior.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1998년도 가을 학술발표회 논문집
• /
• pp.193-200
• /
• 1998

The precast prestressed concrete girders of I-type section are frequently employed to design the short-to-medium span bridge. However, its beam depth is greatly increased as its span length is increased over than about 30m. Therefore, the economic and aesthetic effectiveness are rapidly decreased in case of the span length over 30m. The purpose of this paper is to verify the structural safety on the new spliced two span bridge and analyze the variation of member forces and stress distribution according to the construction stages and time. The new spliced technique is performed by partial post tensioning and release in the U-type girders. The structural characteristics of this technique is the introduction of secondary moment to reduce the bending moment by self weight of precast U-type girders constructed in simply supported beam type. So, it is expected that the structural efficiency of this spliced bridge may be improved more than other techniques.

• Structural Engineering and Mechanics
• /
• 제71권3호
• /
• pp.271-282
• /
• 2019

The span record of cable-stayed bridges has exceeded 1,000 m, which makes research on the maximum possible span length of cable-stayed bridges an important topic in the engineering community. In this paper, span limit is discussed from two perspectives: the theoretical span limit determined by the strength-to-density ratio of the cable and girder, and the engineering span limit, which depends not only on the strength-to-density ratio of materials but also on the actual loading conditions. Closed form equations of both theoretical and engineering span limits of cable-stayed bridges determined by the cable and girder are derived and a detailed parametric analysis is conducted to assess the engineering span limit under current technical conditions. The results show that the engineering span limit of cable-stayed bridges is about 2,200 m based on materials used available today. The girder is the critical member restricting further increase in the span length; its compressive stress is the limiting factor. Approaches to increasing the engineering span limit are also presented based on the analysis results.

• 한국강구조학회 논문집
• /
• 제24권1호
• /
• pp.101-108
• /
• 2012

강바닥판 교량은 비교적 얇은 강판이 사용되며, 가로 세로리브 및 가로보 등의 구조부재가 용접에 의해 복잡한 형상으로 조립되므로 용접에 의한 변형과 결함이 발생할 가능성이 매우 높고, 용접연결부에서의 응력 상태가 매우 복잡하다. 또한 실제 강바닥판 교량에서의 피로균열은 주부재보다 2차부재와의 용접연결부에서 발생되고 있다. 그러나 강바닥판교량 설계시에는 대부분 주부재에 대한 응력 평가가 이루어지고 있으며, 피로균열이 발생하는 구조상세에 대한 상세 응력 평가 및 특성 분석은 거의 검토되고 있지 있다. 본 연구에서는 공용년수 29년된 개단면 세로리브를 가진 강바닥판을 대상으로 피로균열의 원인을 조사하고, 재하시험 및 실교통류 흐름하에서의 현장계측을 통하여 대상 교량의 피로안전성을 검토하였다. 또한 피로균열이 발생된 세로리브 및 다이아프램의 용접부를 대상으로 격자해석 및 상세해석 모델을 사용하여, 이들 구조상세에 대한 영향면해석을 이용하여 이동하중에 따른 거동 특성을 조사하고, 대상교량의 피로균열 발생 원인을 규명하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제13권1호통권53호
• /
• pp.179-185
• /
• 2009

최근 건설구조물에 대한 FRP의 활용에 관한 연구가 활발히 진행되고 있다. FRP는 단위중량당의 강도와 강성이 기존 건설재료인 강재나 콘크리트에 비해 매우 크고, 부식에 대한 저항성이 뛰어나는 등의 여러 가지 물리적, 화학적 장점이 있다. 이러한 장점을 이용하여 FRP 외양관을 단면의 효율성을 극대화할 수 있고 경제성과 경관에 매우 효과가 큰 스트럿을 가진 PSC 박스거더교의 스트럿 부재의 피복재로 적용하고자 한다. 본 논문에서는 스트럿을 가진 PSC 박스거더에 사용되는 FRP 외양관의 적용성을 평가하기 위하여 이와 관련한 FRP 외양관의 시편실험과 FRP로 피복된 콘크리트 부재의 압축실험을 수행하였으며, 실험결과로부터 콘크리트 강도와 에너지 흡수능력 및 연성이 증진되어 스트럿 부재로써 충분한 안전성을 확보할 수 있음을 확인하였다.

• 복합신소재구조학회 논문집
• /
• 제6권2호
• /
• pp.77-84
• /
• 2015

The purpose of this study was the analytical safety evaluation on the super-structure of precast modular bridge using standardized modular members and robotic construction during the transportation routing and lifting conditions. In order to evaluate the safety performance of the bridge system, 3-D full scale Finite Element (FE) of 40 m standardized modular block was developed in ABAQUS, followed by the analytical study to classify the structural system according to steel girder structures: 1) modular bridge block lifting method including the steel girder system; 2) modular bridge block lifting method without the steel girder system. The results from the analytical study revealed that the maximum stress of each modular member was within the maximum allowable stresses during lifting condition. However, the stress concentration at the connected area was more critical in comparison to the behavior of 40 m combined modular blocks during lifting time

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2004년도 가을 학술발표회 논문집
• /
• pp.511-516
• /
• 2004

The objective of this study is to optimally design FRP-concrete members of a bridge structure. Using the GENESIS7.0 that is a commercial optimization program we performed an optimal design with design parameters that consist of height, width of FRP member, height of concrete. And we practiced an optimal design with the design variables, thickness of upper flange, bottom flange, and web. The results of these studies are summarized as follows : (1) Thickness of composite-concrete is proper at over loon (2) FRP member reaches the optimal section when the width of the FRP member is 20cm its height is 10cm and the height of the composite-concrete is 12cm.