• Journal of Sensor Science and Technology
• /
• v.27 no.6
• /
• pp.380-385
• /
• 2018

Recently, interest in baseball has been increasing as the level of international baseball games, the popularity of domestic leagues, and the number of players entering the MLB has increased. In this paper, we propose a pitching system that can be applied to both professional and amateur baseball. The pitching system consists of a control module using MSB764T PLC, a pitching mechanism including AC motors and a ball feed rail, an HMI using the CHA-070WR model, inverter, etc. To pitch the breaking balls, the two AC motors each use an inverter to independently control the speed. The implemented pitching system was experimented on, investigating ball speed and ball movement according to RPM using the BUSHNELL Velocity Speed Gun. Experimental results on ball speed are similar to the theoretical data and the measured data. From the experimental data, it is confirmed that the damping coefficient value for the pitching ball is about 0.98. In the case of the breaking ball, the larger the difference between the speeds on the sides of the ball and the faster the ball speed, the larger the bending degree.

• Corrosion Science and Technology
• /
• v.4 no.5
• /
• pp.211-216
• /
• 2005

Failure analysis of the latch ram ball and the C-ram ball with the trade name AFBMA Gr. 50 Colmonoy No. 6, has been performed to identify the root cause of the failure. The study required the extraction of the both failed and normal balls from the nuclear fuel exchanger. Microstructures of both balls were examined after polishing and etching. Breaking tests of both the ball revealed similarity in cleavage surfaces. Fracture surfaces of both failed ball and normal ball after breaking test were examined with SEM and EDX. Microstructure of the ball revealed an austenite phase with coarse Cr rich precipitate. Indented marks observed on the surface of the failed ball are believed to be produced by overloading. In the light of the afore mentioned observations and studies, the failure mechanism of the ball in nuclear fuel exchanger seem to be caused by impact or mechanical overloading on ball.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2003.09a
• /
• pp.98-106
• /
• 2003

To construct pile-supported wharf structures that must support heavy horizontal loads, both vertical piles and batter piles are used. Batter piles are used to secure the bearing capacity against the horizontal loads. However, past case histories have shown that the heads of batter piles are vulnerable because these heads are subjected to excessive axial loads during earthquakes. Therefore, the aseismatic reinforcement method must be developed to prevent batter pile heads from breaking due to excessive seismic loads. Two different connecting methods of either inserting rubber or ball-bearing between batter pile head and upper plate were proposed to improve the aseismatic efficiency. Three large-scale pile head models(rubber type model, ball-bearing type model, and fixed type model) were manufactured and horizontal loading tests were peformed for these models. The results showed that the force-displacement relationship of the fixed type model was linear, but that of the rubber type model and the ball-bearing type model was bilinear. The increase in the horizontal displacement led to the increase in the horizontal stiffness of the rubber type models and the decrease in that of the ball-bearing type model. Compared with the values for fixed type model, the damping ratios of the rubber type model and the ball-bearing type model increased about 33~185％ and 263~269％, respectively.

• Clinics in Shoulder and Elbow
• /
• v.22 no.2
• /
• pp.110-112
• /
• 2019

In reverse ball shoulder replacement, surgery is usually performed using a deltopectoral approach or an anterosuperior transdeltoid approach. The deltopectoral approach is to incise the pectoralis major to upper 1/3 to 1/2, and subscapularis tendon should be removed at the lesser tuberosity of the humerus. This approach has the problem of breaking the shoulder deltoid instead of incising the rotator cuff. Therefore, we report a detailed procedure of reverse ball shoulder replacement using approach without incision of the pectoralis major muscle and subscapularis muscle.

• Asian-Australasian Journal of Animal Sciences
• /
• v.9 no.6
• /
• pp.723-726
• /
• 1996

A water loaded pressure device using water as the breaking force was developed to evaluate eggshell strength and compared with a dropping ball techniques. Further, relationships of shell thickness and weight of eggs to shell strength were also studied. Values for both of the shell strength measuring methods showed a highly significant correlation (p < 0.001) with shell thickness. The water loaded pressure method had a much higher simple correlation coefficient for shell thickness (r = + 0.786) than the dropping ball method (r = + 0.577). The shell strength measured by the water loaded pressure method appeared not to be correlated to egg weight. On the other hand, the negative sign of the standard partial regression coefficient and the partial regression coefficient of egg weight in the estimated multiple regression equation implied that for a given shell thickness a larger egg tended to have less shell strength than a smaller egg.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.102-106
• /
• 1996

In the ball end-milling process of a 3-dimensional mold, it is important to select cutting conditions and tool path considering the geometrical shape of a workpiece to reduce machining time. In this study, experiments were performed to decide allowable feed rate not breaking stability of system for different geometrical shapes. It was found that downcut is more stable than upcutting in machining side wall and downward is preferable to upward in inclined part depending on the angle of the inclination and depth of cut.

• Journal of Fisheries and Marine Sciences Education
• /
• v.17 no.1
• /
• pp.35-47
• /
• 2005

The purpose of this study is to investigate various kinds of discipline problems in middle school classrooms, and the differences in severity and frequency of the classroom discipline problems between male and female students' classrooms in middle schools. This study shows that the discipline problems in the middle school classrooms include using a cellular phone, chattering, sleeping, chewing gum, reading comic books, asking useless questions, challenging a teacher, fighting, calling names, skipping class, throwing trash in the classroom, breaking classroom equipment, creating disorder, losing materials, playing with a ball in the classroom, gambling, and so on. Generally, male students recognized the severity of the classroom discipline problems more than the female students. However, it is shown that the frequency of discipline problems in male students' classrooms is higher than that in female students' classrooms. From the results of this study, male students have more active discipline problems (playing with a ball in the classroom, throwing trash in the classroom, coming to class late, gambling, cutting in line, and so on). On the other hand, female students have more passive discipline problems (making a noise by using a cellular phone, asking useless questions, sending messages to a classmate, studying other subjects, scattering, and so on).

• Journal of Powder Materials
• /
• v.19 no.3
• /
• pp.226-231
• /
• 2012

In this research, the coating behavior of Mg and Fe desulfurization powder fabricated by low energy and conventional planetary mill equipment was investigated as a function of milling time, which produces uniform Fe coated powders due to milling energy. Since high energy ball milling results in breaking the Fe coated Mg powders into coarse particles, low energy ball milling was considered appropriate for this study, and can be implemented in desulfurization industry widely. XRD and FE-SEM analyses were carried out to investigate the microstructure and distribution of the coating material. The thickness of the Fe coating layer reaches a maximum of 14 ${\mu}m$ at 20 milling hours. The BCC structures of Fe particles are deformed due to the slip system of Fe coated Mg particles.

• Korean Journal of Materials Research
• /
• v.30 no.12
• /
• pp.672-677
• /
• 2020

Expensive PCBN or ceramic cutting tools are used for the processing of difficult-to-cut materials such as Ti and Ni alloy materials. These tools have a problem of breaking easily due to their high hardness but low fracture toughness. To solve this problem, cutting tools that form various coating layers are used in low-cost WC-Co hard material tools, and researches on various tool materials are being conducted. In this study, WC-5, 10, and 15 wt%Ni hard materials for difficult-to-cut cutting materials are densified using horizontal ball milled WC-Ni powders and pulsed current activated sintering method (PCAS method). Each PCASed WC-Ni hard materials are almost completely dense, with a relative density of up to 99.7 ~ 99.9 %, after the simultaneous application of pressure of 60 MPa and electric current for 2 min; process involves almost no change in the grain size. The average grain sizes of WC and Ni for WC-5, 10, and 15 wt%Ni hard materials are about 1.09 ~ 1.29 and 0.31 ~ 0.51 µm, respectively. Vickers hardness and fracture toughness of WC-5, 10, and 15 wt%Ni hard materials are about 1,923 ~ 1,788 kg/mm2 and 13.2 ~ 14.3 MPa.m1/2, respectively. Microstructure and phase analyses of PCASed WC-Ni hard materials are performed.

• The Journal of Korean Academy of Prosthodontics
• /
• v.39 no.3
• /
• pp.260-272
• /
• 2001

All-ceramic restorations have had a more limited life expectancy than metal ceramic restorations because of their low strength. Their relatively lower strength and resistance to fracture have restricted the use of all-ceramic crowns to anterior applications where occlusal loads are lower. But there has been increasing interest in all-ceramic restorations because patients are primarily concerned with improved esthetics. Many efforts have been made to in prove the mechanical properties of dental ceramics. This study was designed to elucidate the influence of the luting agent on the strength of the Empress 2 crown (staining technique) cemented on human teeth. Seventy extracted human permanent molar teeth were chosen. Teeth were prepared for Empress 2 crowns with milling machine on a surveyor. A dental bur was placed in the mandrel that was positioned so that the long axis of the bur was perpendicular to the surveyor base. Dimensions of the Empress 2 crown preparation were $6^{\circ}$ taper on each side, $1.5{\pm}0.1mm$ shoulder margin, and 4mm crown height. The luting cements used in this study were as follow: 1. Uncemented 2. Zinc phosphate cements (Confi-Dental) 3. Conventional glass ionomer cement : Fuji 1 (GC) 4. Resin-modified glass ionomer cements : Fuji plus (GC) 5. Adhesive cements : Panavia F (Kuralay), Variolink II (Vivadent), Choice (Bisco). Fracture test using Instron. The crowns were loaded in compressive force to evaluate the effect of these cements on the breaking strength of these all-ceramic crowns. A steel ball with a diameter of 4mm was placed on the occlusal surface and load was applied to the steel ball by a cylindrical bolt with a crosshead speed of 0.5mm per minute until fracture occurred. The fractured surface was examined using Scanning Electron Microscopic Image (SEM) to discover the correlation between fracture strength and bonding capacity. Within the limitation of this in vitro study design, the results were as follows : 1. fomentations significantly increased the fracture resistance of Empress ceramic crowns compared to control. Uncemented (206.9 N): ZPC (812.9 N): Fuji 1 (879.5 N): Fuji Plus (937.7 N): Choice (1105.4 N): Variolink II (1221.1 N): Panavia F (1445.2 N). 2. Resin luting agent, treated by a silane bond enhancing agents, yielded a significant increase in fracture resistance. In some of the Panavia F group, a fracture extended into dentin. 3. According to SEM images of fractured Empress crowns, the stronger the bond at both interfaces(crown and die), the more fracture strength was acquired.