• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 춘계학술대회논문집
• /
• pp.157-160
• /
• 1999

Aluminum 4343(filler thickness ; 10${\mu}{\textrm}{m}$/Al 3N03(core 80${\mu}{\textrm}{m}$)/Al 4343(filler 10${\mu}{\textrm}{m}$) clad sheet which is recently developed as brazing sheet materials for automotive condensers was fabricated by castinglongrightarrowhot rollinglongrightarrowcold rollinglongrightarrowintermediate annealing(IA)longrightarrowfinal cold rolling(CR). and the effect of IA/CR conditions on microstructure and sagging resistance were investigated the sheet which were fabricated by optimum conditions (IA'ed at 42$0^{\circ}C$ followed by CR'ed to 20~45%) showed good sagging resistance because the core obtained a coarsely recrystallized grain structure during brazing and consequently inhibited filled alloy penetration into the core.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.316-319
• /
• 2008

The L-bending of inner-structure bonded sandwich sheet metal is examined by using a bending die attached to the material testing machine. The specimen is composed of top and bottom layers and a middle layer of pyramid-core structure and each layer is bonded by brazing. The variables chosen for experiments were clearance between punch and die, location of bend line on the specimen surface and clamping type of specimen during L-bending. Effects of these variables on deformation of specimen around die-corner radius were investigated. It was shown that the irregular shapes of recess are formed in the inner layer of bended parts and they greatly depend on working conditions.

• 대한기계학회논문집A
• /
• 제37권12호
• /
• pp.1573-1579
• /
• 2013

핵연료의 연소성능을 시험하기 위해서는 시험 루프에 설치된 조사리그 내에 냉각수가 순환되도록 설계되어야 한다. 이때, 조사리그 내 냉각수는 $300^{\circ}C$, 15.5 MPa 의 고온 고압으로 순환시키기 때문에 냉각수의 밀봉은 핵연료 조사리그를 제작할 때 가장 중요한 공정 중 하나이다. 특히 15 개의 계장선이 조사리그의 압력경계부위를 통과하게 되는데, 이의 밀봉을 위해 일반적으로 브레이징 공정이 적용된다. 본 연구에서는 조사리그 브레이징용 진공챔버 및 고주파 유도가열기를 포함하는 유도 브레이징 시스템을 개발하고, 다양한 실험을 통해 산화막이 발생하지 않는 공정변수를 검토하였으며, 브레이징 제품의 인장시험, 단면검사, 밀봉성능검사 등을 통해 브레이징 공정의 건전성과 밀봉성능을 검증하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제17권1호
• /
• pp.66-72
• /
• 1993

The brazing of Al to Al using Al-Si alloy filler metal was performed under different bonding conditions such as ratio of lap length to plate thickness, surface roughness and joint clearance of the lap joint. The adopted thickness of the base metal in this experiments were two kinds of 4mm and 7mm which were most commonly used in various field. Influence of several bonding conditions of Al/Al joint was quantitavely evaluated by bonding strength test, and microstructural analysis at the interlayer were performed by optical microscope. From above experiments, the optimum bonding conditions of the brazing bonding of Al/Al using Al-Si alloy filler metal was determined. The major results obtained are as follows. 1) The fracture occurs at brazed joint in the conditions of that the ratio of lap length to plate thickness is less than 2 in case of 7mm plate thickness. 2) The ratio of lap length to plate thickness which the fracture occurs at base metal is decreased with the decreasing of the plate thickness. 3) The joint strength is not affected by the surface roughness and joint clearance of the brazed part. 4) The heat-treatment of the brazed joint contribute to eliminate the boundary between the base metal and filler metal. However, the joint strength is not affected by the heat-treatment.

• 한국재료학회지
• /
• 제26권7호
• /
• pp.376-381
• /
• 2016

For the development of a low-melting point filler metal for brazing aluminum alloy, we analyzed change of melting point and wettability with addition of Sn into Al-20Cu-10Si filler metal. DSC results showed that the addition of 5 wt% Sn into the Al-20Cu-10Si filler metal caused its liquidus temperature to decrease by about 30 oC. In the wettability test, spread area of melted Al-Cu-Si-Sn alloy is increased through the addition of Sn from 1 to 5 wt%. For the measuring of the mechanical properties of the joint region, Al 3003 plate is brazed by Al-20Cu-10Si-5Sn filler metal and the mechanical property is measured by tensile test. The results showed that the tensile strength of the joint region is higher than the tensile strength of Al 3003. Thus, failure occurred in the Al 3003 plate.

• Journal of Welding and Joining
• /
• 제30권6호
• /
• pp.27-35
• /
• 2012

• Journal of Welding and Joining
• /
• 제22권5호
• /
• pp.9-12
• /
• 2004

• Journal of Welding and Joining
• /
• 제22권5호
• /
• pp.13-17
• /
• 2004

• 한국항공우주학회지
• /
• 제31권7호
• /
• pp.112-117
• /
• 2003

본 연구에서는 재생 냉각용 연소기에 적용되고 있는 동합금과 2상 스테인리스강의 최적 브레이징 조건을 구하였다. 모재는 C18200 동합금과 S31803 2상 스테인레스강을, 삽입금속으로 두께가 각각 50${\mu}m$, 80${\mu}m$인 AMS4764를 사용하였다. 브레이징한 시제에 대하여 X선 검사, 강도/기밀 및 파괴시험, 파단면 관찰을 한 결과 두께 50${\mu}m$인 삽입금속을 사용한 경우 강도특성과 접합면이 양호함을 확인하였다. 반면 두께 80${\mu}m$인 삽입금속을 사용한 경우는 강도특성은 양호하였으나 냉각유로의 막힘 현상과 유로 확대를 확인하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권5호
• /
• pp.691-698
• /
• 2004

레이저빔과 아크를 하나의 용접 프로세스로 병합하는 기술에 관해서는 이미 70년대부터 알려져 왔으나 별다른 개발로 이어지지 못하다가 최근에서야 다시 눈을 돌리게 되었다. 이 기술의 핵심과제는 아크의 장점과 레이저의 장점을 어떻게 단일 혼합 프로세스로 조합하느냐 하는 것이다. 과거 레이저빔을 처음 사용할 때 만해도 산업용으로서 적합성을 증명해야 했으나 지금은 이미 자동차 산업에서 재래기술로 치부되고 있다.(중략)