• Tribology and Lubricants
• /
• 제31권2호
• /
• pp.42-49
• /
• 2015

Because of the growing need for high-speed transport options such as trains and aircraft, there is increasing demand for technology related to high-speed trains. Among them, braking systems are important in high-speed trains in terms of reliability. Especially, the disk brake system, in use in most high-speed trains, transforms kinetic energy into thermal energy and noise. Therefore, the material properties of both the friction materials and disks are expected to influence the tribological characteristics. In this paper, the tribological characteristics depend on the hardness of the brake disks between the Cu-based sintered metallic friction material and the heat-treated heat-resisting steel disks. A lab-scale dynamometer used to perform braking tests at a variety of braking speeds using dry conditions. The test results revealed that the hardness of the disks affects the friction coefficients, friction stabilities, and wear rates. Thus, the brake system using the heat-resisting steel disk requires proper heat-treatment. These differences are considered to be caused by the change in tribological mechanisms and the generation of an oxide layer on the friction surfaces. The oxide layers on the friction surfaces are confirmed to Fe₂O₃ by x-ray diffraction (XRD) and scanning electron microscope-energy dispersive spectroscopy (SEM-EDS) analysis.

• 대한기계학회논문집A
• /
• 제37권5호
• /
• pp.673-678
• /
• 2013

크립 그론 소음은 자동차 브레이크에서 제동압 제거 초기나 제동 말기에 발생하는 저주파 소음 현상이다. 이러한 현상은 브레이크 시스템에 국한되는 문제가 아니라 샤시의 진동특성에도 영향을 받는 것으로 예측되고 있기 때문에 그 특성 파악이 어려운 것으로 알려져 있다. 때문에 현재까지의 연구는 마찰재를 통한 개선이 대부분이었다. 그래서 실차를 이용한 실험은 여전히 어려운 과제로 남겨져 있다. 이번 연구는 환경에 민감한 크립 그론 소음의 특성과 샤시 진동특성의 영향을 실차와 NVH 전용 샤시 다이나모를 이용한 여러 가지 실험을 통해 알아 보았다. 이를 통해 실차에서의 새로운 크립 그론 소음 평가시 중요한 통제변수를 제시하고 차량 시스템 측면에서 소음 저감 대책 연구에 대한 가능성을 확인할 수 있었다.

• 한국철도학회논문집
• /
• 제14권2호
• /
• pp.100-108
• /
• 2011

본 논문은 고속철도 디스크 브레이크용 유연 제동 패드의 성능 향상을 위해 구조적 안정성 검토와 신뢰성에 대한 연구를 수행하였다. 연구에서는 유연패드의 구조 해석 과정을 거쳐 개선된 모델을 얻어내었으며, 실제 크기와 동일한 1/2 모델을 가지고 구조적 안전성을 확인하였다. 또한, 축소 시편을 제작하여 모달 시험과 스트로크 및 내구성 시험을 수행하여 동 특성과 기계적 안정성을 확인하였다. 샤시 다이나모 장비와 열 적외선 캠코더를 이용하여 유연패드에 대하여 회전 속도에 따른 열섬 발생 현상을 측정하고, 디스크와 패드 사이의 균일한 접촉 능력을 확인하였다. 또한, 제동 시 유연패드에 안정적인 온도 분포가 이루어지는 것을 확인할 수 있었다. 이와 같은 결과를 토대로 제안된 유연패드의 구조 안정성 및 열에너지 방출 효과 등의 장점을 확인하였다.

• Tribology and Lubricants
• /
• 제30권6호
• /
• pp.330-336
• /
• 2014

Sintered metallic brake pads and low alloy heat resistance steel disks are applied to mechanical brake systems in high energy moving machines that are associated with recently developed 200km/h trains. This has led to the speed-up of conventional urban rapid transit. In this study, we use a lab-scale dynamometer to investigate the effects of the composition of friction materials on the tribological characteristics of sintered metallic brake pads and low alloy heat resistance steel under dry sliding conditions. We conduct test under a continuous pressure of 5.5 MPa at various speeds. To determine the optimal composition of friction materials for 200 km/h train, we test and the evaluate frictional characteristics such as friction coefficients, friction stability, wear rate, and the temperature of friction material, which depend on the relative composition of the Cu-Sn and Fe components. The results clearly demonstrate that the average friction coefficient is lower for all speed conditions, when a large quantity of iron power is added. The specimen of 25 wt% iron powder that was added decreased the wear of the friction materials and the roughness of the disc surface. However when 35 wt% iron powder was added, the disc roughness and the wear rate of friction materials increased By increasing the amount of iron powder, the surface roughness, and temperature of the friction materials increased, so the average friction coefficients decreased. An oxidation layer of $Fe_2O_3$ was formed on both friction surfaces.

• Composites Research
• /
• 제16권4호
• /
• pp.22-28
• /
• 2003

본 연구는 자동차용 알루미늄 합금 디스크에 적용하기 위만 마찰재 제조에 관만 내용을 제시한 것이다. 최적 마찰재 조성을 확보하기 위하여 섬유, 결합재, 충진재, 마찰 성능 조정재 등으로 분류할 수 있는 각 원재료를 채택, 배합 설기에 의한 마찰재 시편을 제작하였으며 그 특성을 실제 차량 1/5 크기의 브레이크 다이나모미터를 이용하여 평가하였다. 마찰성능을 JASO C406 Pl에 준하여 실험만 결과 마찰계수가 0.35∼0.38. fade율이 18%였으며, 내 마모성은 JASO C427에 준하여 온도별 마모시험을 실시하였는데 시험 종료후 마찰재의 마로량이 1.6mm, 디스크 마모량이 0.08mm 수준인 우수한 배합 조성을 획득할 수 있었다. 시험 전$.$후의 마찰재와 알루미늄 합금 디스크의 표면상태는 주사전자현미경을 이용하여 관찰하였다.

• 한국자동차공학회논문집
• /
• 제21권1호
• /
• pp.61-67
• /
• 2013

In this paper, it was studied how the critical speed which could occur hot judder due to disk temperature. Through the dynamometer experiment, we measured the critical velocity and surface temperature when the hot judder occur on the disk break. Also with the critical velocity theory equation and the temperature change graph of factors which used in the equation, we was induced experiment equation including theory equation and experiment values. And it has compared with the method which approach as linea. From this, we predicted the change of critical speed which could occur hot judder due to disk temperature. In addition, critical speed graph has compared with actual driving speed and disc temperature at a vehicle test. Therefore it was estimate to possibility of arising hot judder.

• 한국자동차공학회논문집
• /
• 제20권6호
• /
• pp.61-66
• /
• 2012

Conventional method to transform vehicle driving condition to engine operation mode is to use vehicle road load under neutral gear and mechanical efficiency of drivetrain. But this method requires additional measurement of efficiency of drivetrain on a test rig. And this measurement is normally done at fixed speed and thus estimated accuracy of engine operation mode is not considered to be high enough. This study suggests new method to calculate engine operation mode for prescribed driving mode such as NEDC using vehicle coastdown test under gear engaged condition without measurement of mechanical efficiency of drivetrain. Coastdown test was done under neutral and gear engaged condition for comparison and also trial to extract mechanical loss of drivetrain was carried out. Calculated engine torque by conventional and newly suggested method was compared with actually measured torque of a vehicle on a chassis dynamometer during NEDC. Newly suggested method showed slightly higher accuracy of accumulated brake work during NEDC.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.89-90
• /
• 2008

This paper studies the effect of pad at initial stage and wear during braking on the dynamic contact pressure distribution. Wear is influenced by variable factor (contact pressure, sliding speed, radius, temperature) during dynamic braking and variation in contact pressure distribution. Many researchers have conducted complex eigenvalue analysis considering wear characteristic with Lim and Ashby wear map. The conventional analysis method is assumed the pad has smooth and flat surfaces. The purpose of this paper is to validate that wear rate induced by braking is considered for the precise squeal prediction. After obtaining pad wear from experiment, it is incorporated with FE model of brake system. Finally, the comparisons in fugitive nature of squeal will be carried out between the complex eigenvalue analysis and noise dynamometer experiment.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.899-905
• /
• 2000

The characteristics of air flow and engine performance with swirl ratio variance of intake port In a turbocharged DI diesel engine was studied in this paper. The intake port flow is important factor which have influence on the engine performance and exhaust emission because the properties in the injected fuel depend on the combustion characteristics. The swirl ratio for ports was modified by hand-working and measured by impulse swirl meter. For the effects on performance and emission, the brake torque and brake specific fuel consumption were measured by engine dynamometer and NOx, smoke were measured by gas analyzer and smoke meter. As a result of steady flow test, when the valve eccentricity ratio are closed to cylinder wall, the flow coefficient and swirl intensity are increased. And as the swirl ratio is increased, the mean flow coefficient is decreasing, whereas the gulf factor is increasing. Also, through engine test its can be expected to meet performance and emission by optimizing the main parameters; the swirl ratio of intake port, injection timing and compression ratio.

• 동력기계공학회지
• /
• 제9권4호
• /
• pp.5-10
• /
• 2005

The effect of ultrasonic energy for diesel fuel and blend oil has been revealed in this paper. The experimental setup consisted of a high speed diesel engine with 4 cylinder, dynamometer and ultrasonic fuel feeding system. Ultrasonic energy was added to diesel fuel and blend oil, which is a blend of diesel fuel and rape-seed oil. As engine speed was changed, engine torque and power, brake specific fuel consumption and thermal efficiency were measured in detail. As the results, by adding ultrasonic energy to diesel fuel and blend oil, the engine performance was improved in range of the experiment. The effect of improvement on brake specific fuel consumption and thermal efficiency for blend oil is higher than that for diesel fuel. When ultrasonic energy was added to diesel fuel or blend oil, a rise in engine torque for diesel fuel was higher than that for blend oil, but the effect of ultrasonic energy was small. From these results, it may be desirable to add ultrasonic energy to blend oil for the use of blend oil to diesel engine.