• 한국항공우주학회지
• /
• 제42권7호
• /
• pp.567-575
• /
• 2014

본 논문에서는 스마트 스킨 시제품을 항공기에 장착하고 비행데모시험을 수행하는 절차와 시험결과를 제시하였다. 통신항법용 4개의 안테나를 한 개의 안테나 내장 스킨구조(CLAS)에 삽입하였다. 대수주기 패치형 안테나를 4개의 안테나 주파수 대역을 포함하도록 다중대역 안테나로 설계하였다. 항공기에 장착하기 전에 안테나 내장 스킨구조의 요구조건은 지상시험으로 입증하였다. CLAS 스피드브레이크를 KT-1 항공기에 장착하고 2개 이상의 안테나를 작동시키는 다중 안테나 시험을 지상에서 수행하였다. 항공기에 장착된 기존 장비들과 CLAS와의 호환성을 확인하기 위해 전자파 적합성시험을 수행하였다. 비행데모시험은 4개의 안테나에 대하여 각 1회의 비행을 수행하였다. 비행 중 안테나 통신항법 신호의 작동상태와 지속성, 항공기 원형 비행 시 사각지대 유무 확인을 하였다. 안테나 내장 스킨구조의 안테나는 4회 비행데모시험 동안 기대 이상의 성능을 보여주었다.

• 한국산학기술학회논문지
• /
• 제21권9호
• /
• pp.596-603
• /
• 2020

전기기계식 제동장치(EMB : Electro-Mechanical Brake)는 자동차 및 철도차량의 차세대 제동장치로서 현재 연구가 활발히 진행되고 있다. 현재의 철도차량용 제동장치는 공압 실린더를 이용하여 제동 압부력을 발생시키나 전기기계식 제동장치 (EMB)에서는 전기 모터 및 기어와의 조합을 통하여 압부력을 발생시킨다. 본 연구에서는 고압부력 발생이 가능한 편심회전축 기반의 전기기계식 제동장치에 대한 유한요소 모델링 및 내구 수명해석을 통하여 국내 기준에 부합하는 전기기계식 제동장치의 설계를 진행하였다. 이때 내구수명해석의 정확도를 향상하기 위하여 시제품에 사용되는 소재와 동일한 열처리 등을 거친 피로시험 시편을 3종을 제작하여 소재별로 피로시험을 진행하였다. 각각의 소재에 대한 피로시험 결과로부터 피로물성치(응력-수명 선도)를 획득하여 해석모델에 반영하였다. 피로해석 결과로부터 EMB 시제품의 설계가 국내 철도차량용 내구수명 조건인 상용최대 제동/완해 53 만회를 만족할 수 있음을 확인하였다. 또한, 이 설계를 바탕으로 시제품을 제작하고 내구시험을 완료하여 개발된 시제품의 내구성 특성을 입증할 계획이다.

• 한국자동차공학회논문집
• /
• 제22권4호
• /
• pp.145-151
• /
• 2014

Modern vehicle has a lot of ECU(Electronic Control Unit) products to control many parts such as engine, transmission, brake, body and so on. ECU quality is one of important factors related to vehicle quality and driver's safety. Based on Bath-tub curve which presents failure rate during product lifetime, we designed and applied Accelerated Run-in Test into manufacturing line by simulating stress amount to ECU and developing the required software and efficient test equipment for mass production. This test makes ECU products stressed through electrical and thermal stresses under excessive driving condition, which induce potential initial failure of components in the ECU during production. The outcome until these days proved that Acceleration Run-in Test have reduced initial failure rates and increased quality of ECU products in the field outstandingly.

• 대한의용생체공학회:의공학회지
• /
• 제38권4호
• /
• pp.143-152
• /
• 2017

The main purpose of this research was to examine the EMG characteristics of driver's upper limb and driving performance for operating accelerator and brake pedal by using four types of left hand control devices(Push/Pull, Push/Right angle, Push/Rock, Push/Twist) during simulated driving. The persons with disabilities in the lower extremity have problems in operation of the vehicle because of functional impairments for controlling accelerator and brake pedal. Therefore, if hand control device is used for adaptive driving controls in persons with lower extremity loss, the disabled people could improve their quality of mobility life by driving a car. Twenty subjects were involved in this research to assess driving performance and EMG activities for operating accelerator and brake pedal by using four types of left hand controls in driving simulator. We measured EMG responses of six muscles(posterior deltoid, middle deltoid, biceps, triceps, extensor carpi radialis, and flexor carpi radialis) during pulling and pushing movement with four types of left hand controls for acceleration and braking. STISim Drive 3 program was used for evaluation test of four types of left hand control devices in straight lane course for time to reach target speed and brake reaction time. While operating the four types of left hand controls for acceleration, EMG activities of posterior deltoid in normal subjects were significantly increased(p < 0.05) compared to the disabled subjects. It was also found that EMG responses of triceps and posterior deltoid were significantly increased(p < 0.05) when using the Push/Right angle type than Push/Pull type. While operating the four types of left hand controls for braking, EMG activities of flexor carpi radialis and triceps in subjects with disability were significantly increased(p < 0.05) compared to the normal subjects. It was shown that muscle responses of posterior deltoid, middle deltoid and triceps were significantly increased when using the Push/Right angle type than Push/Rock type. Time to reach target speed and brake reaction time in subjects with disability was increased by 2.5% and 4.6% on average compared to normal subjects. The person with disabilities showed a tendency to relatively slow performance in acceleration at the straight lane course.

• 한국산학기술학회논문지
• /
• 제20권12호
• /
• pp.237-246
• /
• 2019

전기기계식 제동장치(EMB : Electro Mechanical Brake)는 자동차 및 철도차량의 차세대 제동장치로서 현재 연구가 활발히 진행되고 있다. 현재의 고속열차용 제동장치는 공압 실린더를 이용하여 제동 압부력을 발생시키나 전기기계식 제동장치 (EMB)에서는 전기 모터 및 기어와의 조합을 통하여 압부력을 발생시킨다. 본 연구에서는 고압부력 발생이 가능한 EMB 구동 메커니즘을 제안하고, 해당 메커니즘을 만드는 기구장치 중 핵심부품인 기어 및 샤프트 부품들에 대한 구조 및 진동해석을 수행하였다. 한편 모델에 대한 동적 진동해석 결과 압부력이 가해진 상태에서 외부가진이 주어졌을 때 부재의 최대 응력이 항복강도 이내임이 확인되었다. 또한, 구조해석 결과 모터샤프트의 축 직경을 최대한 크게하는 설계가 강도 상 유리함을 확인하였으며, 기어와 편심샤프트를 고정하는 볼트에서 큰 전단응력이 발생할 수 있음을 확인하였다. 한편 해석모델의 메커니즘을 재현할 수 있는 시험장치를 제작하여 가장 취약한 부위인 고정 볼트부의 변형률을 구동 토크가 가해진 상태에서 측정하였다. 변형률 측정결과는 해석결과와 오차가 10% 이내로서, 해석모델의 정확도를 검증할 수 있었다.

• 한국철도학회논문집
• /
• 제8권6호
• /
• pp.566-572
• /
• 2005

This paper describes the results of structural analysis and loading test of a bogie frame. The purpose of the analysis and test is to evaluate the safety and functionality of the bogie frame under maximum load. The bogie system consist of the bogie frame, suspensions, wheel-sets, a brake system and a transmission system. Of these components, the bogie frame is the major components subjected to the vehicle and passenger loads. The evaluation method used the JIS E 4207 specifications throughout the FEM analysis and static load test. The test results have shown the bogie frame to be safe and stable under design load conditions.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.34-38
• /
• 2005

This paper describes the result of load test of a bogie frame. The purpose of test is to evaluate the safety which bogie frame shall be considered fully sufficient rigidity so as to satisfy proper system function under maximum load. Bogie system consist of the bogie frame, suspensions, wheel-sets, a brake system and a transmission system. Among these component, the bogie frame is most significant component subjected to the vehicle and passenger loads. The evaluation method is used the JIS E 4207 specifications throughout the static load test. The test results have shown the bogie frame to be safe and stable under design load conditions.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.199-205
• /
• 2004

This paper describes the result of structure analysis and load test of bogie frame. The purpose of the analysis and test is to evaluate an safety which bogie frame shall be considered fully sufficient rigidity so as to satisfy proper system function under maximum load. Bogie system consist of bogie frame, suspensions, wheel-sets, brake system and transmission system. Among these component, the bogie frame is most significant component subjected to the vehicle and passenger loads. The evaluation method is used the JIS E 4207 specification throughout the FEM analysis and static load test. The test results have been very safety and stable for design load conditions.

• 한국초전도ㆍ저온공학회논문지
• /
• 제2권2호
• /
• pp.44-48
• /
• 2000

The high temperature superconducting bulk can be used as the rotor of an ac motor. This paper presents the fabrication and test results of a ac motor with HTS bulk rotor. The rotor of a conventional squirrel cage induction motor was replaced with cylinder type YBCO bulk. Height and outer diameter of the HTS bulk was 15mm and 46mm, respectively. Eddy current brake using aluminium disk was used to measure the torque of the HTS motor. No load test, locked rotor test and load test were performed to examine the characteristics of the HTS motor. Test results show the motor can rotate at synchronous speed without any special starting circuit. Maximum output power of the constructed HTS motor was 408W.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.611-618
• /
• 2000

The test facility of the 1/60-scale models for the train-tunnel interactions was recently developed to investigate the effects of entry portal shapes, hood shapes and air-shafts for reducing the micro-pressure waves radiating to the surroundings of the tunnel exits by KRRI in Korea. The launching system of train model was chosen as air-gun type. In present test rig, after train model is launched, the blast wave by the driver did not enter to inside of the tunnel model. The train model is guided on the one-wire system from air-gun driver to the brake parts of test facility end. Some cases of the experiments were compared with numerical simulations to prove the test facility.