• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.426.2-426.2
• /
• 2014

Wavefront control은 렌즈, 거울 등을 포함한 많은 광학소자를 대체할 수 있는 기술이며, 이는 광 직접 소자 개발에 매우 유용하다. 기존의 Distributed bragg reflector (DBR) 구조의 경우 lattice mismatch, 낮은 효율, 작은 굴절률 차이의 물질만을 사용해야 하는 문제 등으로 광 직접 소자에의 적용에는 한계가 있다. 본 연구에서는 이러한 한계점을 극복하고, 더 나아가 광학소자 구조 내에서의 빛의 거동을 조절하기 위해서 High-index contrast grating (HCG), 즉, 큰 굴절률 차이가 나는 물질로 이루어진 격자 구조 내의 빛이 가지는 waveguide 특성에 대한 연구가 수행되었다. 굴절률 차이가 큰 물질을 sub-wavelength의 주기적인 혹은 비주기적인 격자 구조로 만듦으로써 투과된 빛의 투과도와 위상 등을 조절할 수 있고 이를 통해 빛의 초점 거리, 휘어짐을 조절 할 수 있다. HCG 구조 내의 빛의 거동을 Rigorous coupled wave analysis (RCWA) 및 Finite element method (FEM) 계산을 이용하여 시뮬레이션 하였다. RCWA 계산을 통해 주기 격자구조의 투과도 및 반사도, 빛의 위상을 계산하여 비주기를 갖는 전체적인 HCG 구조를 결정하였고, FEM 계산을 통하여 그 구조 내에서 빛의 거동을 시뮬레이션 하였다. 1,300 nm 파장의 빛이 광원으로 사용되었고 시뮬레이션을 위해 낮은 굴절률의 물질로 ITO, 높은 굴절률의 물질로는 Si이 사용되었다. $15{\mu}m$ 포커싱, $7.91^{\circ}$의 휘어짐을 시뮬레이션 하였고, 실제 소자 공정을 하여 제작한 후, 광 측정 결과 포커싱은 $15{\mu}m$, 휘어짐은 $4.5{\sim}6.5^{\circ}$를 확인하였다. 이러한 결과를 바탕으로 HCG구조체를 통하여 빛의 엔지니어링이 가능함을 알 수 있었다. HCG구조체는 빛이 투과하는 광학 소자의 전반에 적용이 가능하며 더 나아가 인위적인 빛의 엔지니어링이 가능함을 시사한다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.10
• /
• pp.21-26
• /
• 2003

In this research, the change of coefficient of thermal expansion (CTE) of graphite/epoxy composite laminate under space environment was measured using fiber optic sensors. Two fiber Bragg grating (FBG) sensors have been adopted for the simultaneous measurement of thermal strain and temperature. Low Earth Orbit (LEO) conditions with high vacuum, ultraviolet and thermal cycling environments were simulated in a thermal vacuum chamber. As a pre-test, a FBG temperature sensor was calibrated and a FBG strain sensor was verified through the comparison with the electric strain gauge (ESG) attached on an aluminun specimen at high and low temperature respectively. The change of the CTE in a composite laminate exposed to space environment was measured for intervals of aging cycles in real time. As a whole, there was no abrupt change of the CTE after 1000 aging cycles. After aging, however, the CTE decreased a Little all over the test temperature range. These changes are caused by outgassing, moisture desorption, matrix cracking etc.

• Journal of Sericultural and Entomological Science
• /
• v.40 no.2
• /
• pp.158-162
• /
• 1998

The chitin was isolated from various kinds of insects such as exuvia of Psacothea hilaris Pascoe, silkworm pupa, Agrius convolvuli or from cuticle of cockroach by treatment with dilute HCI and NaOH. The chemical and crystalline structure was characterized by FT-IR and X-ray diffractometer. All of the chitins extracted from insects showed characteristic ${\alpha}$-chitin peaks at the Bragg angle 2$\theta$=9.3$^{\circ}$, 19.4$^{\circ}$, and 23.5$^{\circ}$by X-ray diffraction analysis. The transition from chitin to chitosan was confirmed by IR spectra and the degree of deacetylation of the crab shell, silkworm pupa, cockroach, and Psacothea hilaris Pascoe was 70.9, 76.4, 75.5, and 74.1%, respectively. The double diffraction peaks of insect chitosan were observed at 2$\theta$=10$^{\circ}$and 20$^{\circ}$, indication the characteristic of hydrated crystalline structure of chitosan.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.1
• /
• pp.49-55
• /
• 2002

In this paper, we present the simulation monitoring of strain and temperature during and after the cure of unsymmetric composite laminate using fiber optic sensors. Fiber Bragg grating/extrinsic Fabry-Perot interferometric (FBG/EFPI) hybrid sensors are used to measure those measurands. The characteristic matrix of the sensor is analytically derived and measurements can be done without sensor calibration. A wavelength-swept fiber laser is utilised as a lighr source. Two FBG/EFPI sensors are embedded in a graphite/epoxy unsymmetric cross-ply composite laminate in different directions and different locations. We perform a real time monitoring of fabrication strains and temperatures at two points of the composite laminate during cure process in an autoclave. Also, the thermal strains and temperatures of the fabricated laminate are measured in a thermal chamber. Through these experiments, we can provide a basis for the efficient smart processing of composite and know the thermal behavior of unsymmetric cross-ply composite laminate.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.21 no.6
• /
• pp.607-613
• /
• 2008

A monitoring system for the subway structures using prestrained FBG sensors fixed with partially stripped fibers was developed. The sensor packages had pre-strain controllable fixtures. Tensile and compressive strain of the structure could be measured without slip. The FBG sensor system was applied to the concrete lining structure in Taegu subway. Near the structure, the narrow tunnel construction, for the electric power cables and telecommunication cables, started. We wanted to measure the deformations of the subway structures due to the construction by the FBG sensor. The applied sensors had the gauge length of 1 meter to overcome the inhomogeneity of the concrete material with enough length. In order to fix tightly to the structure, the partially stripped parts of the sensor glued to the package and slip phenomenon between fiber and acrylate jacket was prevented. Prestrain of the sensor was imposed by controlling the two fixed points with bolts and nuts in order to measure compressive strain as well as tensile strain. The behavior of subway lining structure could be monitored very well.

• Korean Journal of Optics and Photonics
• /
• v.17 no.3
• /
• pp.216-222
• /
• 2006

We propose the use of the Gaussian-curve fitting algorithm for the improvement of measurement accuracy in wavelengthscanned Fabry-Perot filter based demodulation systems. The peak locations of FBG sensors were calculated from the fitted curves rather than from distorted PD profiles, resulting in much better measurement accuracy than that of the highest-peak search algorithm. Also, the algorithm was proved to minimize measurement uncertainty of spectrally-distorted grating sensors. From our experimental results, a temperature resolution as small as ${\sim}0.3^{\circ}C$ was readily achieved by use of the Gaussian-curve fitting algorithm whereas the highest-peak search algorithm gave a temperature resolution larger than ${\sim}4^{\circ}C$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.351-351
• /
• 2013

한국 전체 에너지 사용량 중약 24%의 에너지가 건축물 부분에 소비되고 있다. 건축물의 벽체나 유리창 등을 통해서 에너지 손실이 이루어지는데 유리창은 벽체에 비해 약 10배 이상 낮은 단열 특성을 가지고 있기 때문에 유리창을 통한 열손실량은 더 크다. 이러한 유리창 부분의 열손실 문제를 해결할 수 있는 방안으로 좋은 단열 특성 및 낮은 방사율을 가지고 있는 Low-e coating 방법을 사용하였다. 본 실험에서는 XG glass 기판 위에 IGZO/Ag/IGZO OMO 구조의 다층 박막을 증착하였다. RF magnetron sputtering방법을 이용하여 OMO 구조의 상부와 하부의 Oxide layer로 IGZO 박막을 증착하였다. 사용된 IGZO 타겟은 $In_2O_3$ (99.99%), $Ga_2O_3$ (99.99%), ZnO (99.99%)의 분말을 각각 1:1:1 mol% 조성비로 혼합하여 소결하여 제작하였다. Thermal Evaporator 장비를 이용하여 OMO 구조의 Metal layer로 Ag (99.999%)를 증착하였다. 실험 기판은 크기 $30{\times}30mm$의 0.7T XG glass를 사용하였다. OMO 구조의 산화층 IGZO 박막은 상/하층 동일 조건으로 기판 온도는 실온으로 고정하였으며, 초기 압력 $3.0{\times}10^{-6}$ Torr, 증착 압력 $3.0{\times}10^{-2}$ Torr, RF 파워 50W, Ar 유량 50 sccm로 고정시키고 증착 시간이 변화하면서 박막을 증착하였다. OMO 구조의 Metal layer로 Ag 증착 조건은 초기 진공도가 약 $6.0{\times}10^{-6}$ Torr 이하로 유지하고 기판을 2 Rpm의 속도로 회전시켰다. 이후 0.3 V로 Ag를 10분간 가열하여 충분히 녹인 후 Film Thickness Monitor로 두께를 확인하였다. OMO 다층 박막의 산화물층 변화에 따라 로이다층 박막의 구조적, 광학적 및 전기적 특성을 분석하였다. XRD 분석결과에 의하여 Bragg's 법칙을 만족하는 피크가 나타나지 않는 비정질 구조임을 확인할 수 있으며, AFM 분석결과에 통해서 최소 1.3 nm의 Roughness를 나타내었다. UV-Visible-NIR 분광광도계를 이용하여 다층 박막은 가시광선 영역에서 평균 80%의 광 투과성을 보여 IR 영역에서 평균 30% 투과하고 좋은 차단 특성을 나왔다. Low-e 특성을 갖는 유리창을 통해서 에너지 절약을 이룰 수 있는 것을 확인할 수 있었다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.1
• /
• pp.1-12
• /
• 1997

The acousto-optical spectrometer as a new type backend of the receiver system for radio astronomical observations is manufactured for radio signal analysis. We studied on the effect of Acousto-Optic and Acousto-Optic devices and designed the optics system. We manufactured the optical mount and the CCD detector for deflected beam and interface card. This acousto-optical spectrometer consisted of a laser, optics, acousto-optic deflector, CCD detector and Interface card. This system use He-Ne laser as a light source and use optics to get parallel beam and to focus the deflected beam. Acousto-optic deflector converts IF signal to ultrasonic wave and deflect the laser beam according to the Bragg deflection. The ultra wide band acousto-optic deflector has 1 GHz bandwidth and a total of 2,048 channel Charge Coupled Device for signal detection. In this study, we discuss the theoretical description on the effect of Acousto-optics, the design of the optics, manufacture of optical mount, CCD detector, interface card and we presented the results of experiment. As a result of measurement, we have 1,000 channels bandwidth from CCD channels.

• Journal of Korean Association for Spatial Structures
• /
• v.9 no.3
• /
• pp.67-74
• /
• 2009

Presently means of utilizing sensors such as Piezoelectric(PZT) Element for evaluating the affect of oscillator, strain gauge for analyzing physical changes and use of Fiber Bragg Grating(FBG) Sensor are widely practiced in the field. In this study, PZT and FBG sensors were used to tearing damage of cable systems in these sensors. Cable systems are a construction of elements carrying only tension and no compression or bending in membrane structure. But damage detection of cable systems by using existing safety diagnosis is difficult to detect the characteristic change of overall structural action. If cable snaps are occurred to cable release and tear in tension structures, these are set up a vibration. So, we used piezo-electric materials and result of experiment using this was compared with result of experiment using FBG sensors The purpose of this research is to develop of damage detection method of cable system in tensile stress.

• Progress in Superconductivity and Cryogenics
• /
• v.19 no.3
• /
• pp.40-43
• /
• 2017

Carbon coating approach is used to prepare carbon-doped $MgB_2$ bulk samples using low-cost naphthalene ($C_{10}H_8$) as a carbon source. The coating of carbon (C) on boron (B) powders was achieved by direct pyrolysis of naphthalene at $120^{\circ}C$ and then the C-coated B powders were mixed well with appropriate amount of Mg by solid state reaction method. X-ray diffraction analysis revealed that there is a noticeable shift in (100) and (110) Bragg reflections towards higher angles, while no shift was observed in (002) reflections for $MgB_2$ doped with carbon. As compared to un-doped $MgB_2$, a systematic enhancement in $J_c(H)$ properties with increasing carbon doping level was observed for naphthalene-derived C-doped $MgB_2$ samples. The substantial enhancement in $J_c$ is most likely due to the incorporation of C into $MgB_2$ lattice and the reduction in crystallite size, as evidenced by the increase in the FWHM values for doped samples.