• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.5
• /
• pp.263-267
• /
• 2017

The Co-Cr as-cast alloys are widely used in the manufacturing of orthopedic implants made with investment casting techniques because of its high strength, good corrosion resistance and excellent biocompatibility properties. Carbide precipitation at grain boundaries and interdendritic regions is the major strenthening mechanism in the as-cast condition. In this study, effects of GPS (Gas Pressured Sintering) heat-treatment on the microstructure and crystallinity of the as-cast Co-Cr alloy prepared by investment casting were investigated. It was confirmed that the content of metal carbide ($Cr_{23}C_6$) was increased in the grain boundary by using optical microscopy (OM), field-emission scanning electron microscopy (FE-SEM) and energy dispersive spectroscopy (EDS).

• Journal of the Korean Society for Heat Treatment
• /
• v.3 no.1
• /
• pp.34-41
• /
• 1990

Effects of grain size and cold rolling degree on shape memory ability and transformation temperature were studied in Fe-35% Mn-6% Si shape memory alloy. Md point of the alloy was determined by variation of yield stress with test temperature. The Md point measured in this way was linearly increased with increasing grain size. Shape memory ability of the alloy was decreased with increasing grain size, showing a minimum value at around $63{\mu}m$, and then increased with increasing grain size. From this result, it was concluded that the shape memory ability in the grain size smaller than a critical value is controlled by amount of retained ${\gamma}$ and prior ${\varepsilon}$ phase, but that the shape memory ability in the grain size greater than the critical value is mainly dominated by grain boundary area in unit volume of parent phase. The shape memory ability was decreased with increasing deformation degree. This was because the ${\gamma}$ content being available for the formation of ${\varepsilon}$ martensite during bending was decreased with increasing deformation degree.

• Journal of the Korean Society for Heat Treatment
• /
• v.23 no.2
• /
• pp.96-103
• /
• 2010

$Ni_3Al$ is known as a good high temperature structural material because of high yield strength at ambient temperature. However, it is too brittle to use as a structural material because of their weak grain boundary. In this work, orientation measurement and related mechanical properties of directionally solidified NiAl/$Ni_3Al$ two-phase alloys with various compositions (Ni-23~27 at.%Al) were investigated for developing multi-phase DS-processed alloys with the growth rates of 10, 50 and 100 ${\mu}m/s$ in a modified Bridgeman type furnace. It was found that the multi-phase microstructures such as the $\gamma$ dendrite +${\gamma}'$ matrix duplex microstructure was formed in the hypoeutectic composition of 23 at.%Al, $\beta$ dendrite +${\gamma}'$ matrix duplex microstructure in the hypereutectic composition of 26 and 27 at.%Al. And ${\gamma}'$ single phase was formed in the composition of 24.5 and 25 at.%Al. The hypoeutectic alloy including $\gamma$ dendrites with ${\gamma}'$ matrix showed a large elongation of over 70% at room temperature. However, the room-temperature tensile elongation decreased with increasing Al contents because the volume fraction of brittle $\beta$ dendrites in the ductile ${\gamma}'$ matrix increased.

• Journal of Sensor Science and Technology
• /
• v.29 no.1
• /
• pp.59-62
• /
• 2020

Currently, increasing attention is being paid to relaxor-based ferroelectric single crystals in photoacoustic images, especially for high-end applications. Among the crystals are (1-x)Pb(Mg_1/3Nb_2/3)O₃-xPbTiO₃ (PMN-100xPT) single crystals located near their morphotropic phase boundary (x = 0.30-0.35) because of their ultrahigh piezoelectric and electromechanical coupling properties. The alternating current poling (ACP) treatment, rather than the conventional direct current poling treatment, has recently been spotlighted due to its effectiveness in enhancing the piezoelectric properties. So far, it has been suggested that the enhanced piezoelectricity originates from either a domain miniaturization to nanodomains or from an electric-field-induced monoclinic symmetry. In this study, we demonstrate by thermally stimulated depolarization current measurements that the effect of ACP is too complex to be explained using a single mechanism and that the proposed electric-field-induced monoclinic symmetry is unlikely to exist.

• Korean Journal of Materials Research
• /
• v.9 no.7
• /
• pp.695-700
• /
• 1999

Effects of two-step aging treatment on the stress corrosion cracking(SCC) resistance of 7050 Al alloy were investigated by transmission electron microscopy, electrical conductivity measurement and stress corrosion facter(SCF) evaluation. It was found that η', principal hardening phase, transformed to η during over aging above maximum hardness, and SCC resistance was improved by increasing of the size and interspacing of η particles in matrix and grain boundary. The electrical conductivity increased with aging time, but SCF decreased due to the decrease of yield strength. This results mean increase of SCC resistance The optimum two-step aging condition in forged 7050 Al alloy was to be first aged at $120^{\circ}C$ for 6h and then finally aged at $175^{\circ}C$ for 12h.

• Journal of Welding and Joining
• /
• v.2 no.1
• /
• pp.4-17
• /
• 1984

Overlaid weld metals of austenitic stainless steel in a pressure vessel of power reactor are usually post-weld heated for a long period of time after welding. The PWHT is considered as a kind of sensitizing and it is important to check the soundness of the weld metal after PWHT, especially about the precipitation of carbides. The purpose of this report is to obtain information on the relation between the change of microstructure and Post-Weld Heat Treatment in the overlaid weld metals. Metallurgical aspects of the problem on austenitic stainless steel heated at $625^{\circ}C$, $670^{\circ}C$, $720^{\circ}C$ and $760^{\circ}C$ for 3, 10, 30, 100 and 300 hours have been investigated by means of optical-micrography, micro-hardness measurement, scanning electron microscope and electron-probe micro analysis. From the results obtained, the following conclusions are drawn; 1) The PWHT above $625^{\circ}C$ for a long time causes a diffusion of carbon atoms from low alloy steel into stainless steel, and consequently carbon is highly concentrated at the boundary layer of stainless steel. 2) C in ferritic steel migrated to austenitic steel and carbides precipitated in austenitic steel along fusion line. At higher temperatures, the ferrite grains coarsened in the decarburized zone. 3) In the change of microstructure of stainless steel overlaid weld metal, the width of carbides precipitated zone and decarburized zone increased with increase of PWHT temperature and time. 4) At about $625^{\circ}C$ to $760^{\circ}C$, chromium carbides, mainly $M_{23} C_6$, precipitate very closely in the carburized layer with remarkable hardening. 5) Precipitation of delta ferrite from molten weld metal depends on solidification phenomenon. There was a small of ferrite near the bond in which the local solidification time was short, comparing with after parts of weld metal. Shape and amount of ferrite were not changed by Post-Weld Heat Treatment after solidification.

• Journal of the Korean Society for Heat Treatment
• /
• v.17 no.1
• /
• pp.29-35
• /
• 2004

The effect of low tempering in a temperature range of $150{\sim}400^{\circ}C$ on corrosion resistance in 420J2 stainless steel austenitized at $1000^{\circ}C$ was investigated by the application of salt spray test, electrochemical pitting test in 3.5% NaCl solution and DL-EPR test for intergranular corrosion in 0.5M $H_2SO_4$+0.01M KSCN solution. In salt spray test, good corrosion resistance was obtained in a tempering temperature range of $150{\sim}250^{\circ}C$. Pitting potential was increased to the tempering temperature of $250^{\circ}C$, but decreased with the increase of temperature up to $400^{\circ}C$ And it was thought that the degradation of pitting corrosion resistance showed at the tempering temperature of around $400^{\circ}C$ was due to the precipitation of $Cr_7C_3$ of $M_7C_3$ type. The degree of sensitization showed increasing tendency with the increase of tempering temperature, and also Cr depletion phenomena were observed in the vicinity of grain boundary.

• Korean Journal of Veterinary Research
• /
• v.45 no.3
• /
• pp.445-450
• /
• 2005

A 1.35 kg, three-year-old, female, Yorkshire terrier was referred to the veterinary medical teaching hospital of Chungnam National University with an alopecia, scale, polydipsia and polyuria. During hospitalization, the patient revealed swelling and pain of all four foot pads. The hematology indicated nonregenerative anemia. Blood serum chemistry revealed elevation of BUN, serum creatinine and phosphorus contents. Radiographs of feet revealed increased radiodensity in the soft tissue of the foot pad. In ultrasonographs of abdomen, kidneys showed diffusely echodense renal cortex with loss of the normal corticomedullary boundary. Fine needle aspiration of the swollen pad cysts contained a amorphous basophillic chalky, white and pasty material. The culture result was negative for bacteria. In conclusion, it was diagnosed as metastatic calcinosis circumscripta secondary to chronic renal failure. An oral charcoal absorbent and aluminum hydroxide were used to treat this condition. After six weeks treatment, hyperphosphatemia was corrected and metastatic calcinosis circumscriptawas not presented any more.

• Journal of the Korean Society for Heat Treatment
• /
• v.29 no.5
• /
• pp.227-233
• /
• 2016

Phase transformation phenomenon at high temperature was investigated by using designed TiAl-Nb alloys with addition of the ${\beta}$ stabilizer. Examination of dendritic morphologies in arc-melted button ingot could reveal the crystallography of the primary solidification phase. It was found that the addition of ${\beta}$ stabilizer(Nb) shifted the high temperature region of the binary Ti-Al phase diagram to the high Al composition side so that ${\beta}$ phase forms as a primary crystal even at higher Al composition compared with the binary Ti-Al system. The ${\beta}$ was found to be the primary solidification phase for alloys with Al content less than about 52 at.%. The composition of ${\beta}$ solidification in Ti-Al-Nb ternary system could be determined from the partial liquidus projection which was constructed by observing the microstructure of arc-melted buttons. The Ti-46Al-(6, 8)Nb composition was selected for ${\beta}$ solidification and the directional solidification was performed by a floating zone-type DS apparatus at the growth rate 30 mm/hr respectively.

• Korean Journal of Materials Research
• /
• v.28 no.12
• /
• pp.702-708
• /
• 2018

This study deals with the effect of microstructure factors on the strain aging properties of API X70 pipeline steels with different microstructure fractions and grain sizes. The grain size and microstructure fraction of the API pipeline steels are analyzed by optical and scanning electron microscopy and electron backscatter diffraction analysis. Tensile tests before and after 1 % pre-strain and thermal aging treatment are conducted to simulate pipe forming and coating processes. All the steels are composed mostly of polygonal ferrite, acicular ferrite, granular bainite, and bainitic ferrite. After 1 % pre-strain and thermal aging treatment, the tensile test results reveal that yield strength, tensile strength and yield ratio increase, while uniform elongation decreases with an increasing thermal aging temperature. The increment of yield and tensile strengths are affected by the fraction of bainitic ferrite with high dislocation density because the mobility of dislocations is inhibited by interaction between interstitial atoms and dislocations in bainitic ferrite. On the other hand, the variation of yield ratio and uniform elongation is the smallest in the steel with the largest grain size because of the decrease in the grain boundary area for dislocation pile-ups and the presence of many dislocations inside large grains after 1 % pre-strain.