• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.207-208
• /
• 2002

In the present study, the friction and wear properties of boundary lubricated textured surfaces were investigated. The capability of textured surfaces to feed lubricant into the interface of a sliding contact and to isolate wear partices was studied and related to the properties of the textured surfaces. Well-defined surface textures were produced by lithography and anisotropic etching of silicon wafers. Different widths and distributions of parallel groves were manufactured and subsequently the wafers were PVD coated with thin wear resistant TiN or DLC coatings, retaining the substrate texture. The surfaces were evaluated in reciprocating sliding against a ball bearing steel ball under starved or boundary lubricated conditions.

• Journal of the Korean Society for Precision Engineering
• /
• v.7 no.2
• /
• pp.113-123
• /
• 1990

To study deleterious effects of contaminants contained in lubricating systems, the effects of fine alumina particle concentration and size on the critical failure load, friction and wear characteristic were examined on boundary lubrication condition using the four ball machine. The following conclusions are deduced: The abrasive is found to cause a transition from mild wear to severe wear at less severe conditions than with clean oil. In mild wear region the friction and wear increase with particle size and concentration, but in severe wear region do not exhibit any definite trend. In relation to film thinckness there is a threshold of particle size beyond which the failure load no longer decreases with particle size.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.4 no.2
• /
• pp.46-53
• /
• 1995

In this study, Wear of a ceramic cutting tool for hardened STD11 steel was investigated. Under the finish machining condition. DOC notch wear of a ceramic cutting tool was mostly occurred earlier than flank and crater wear were proceeded. The relations of DOC notch wear, which was characteristically produced at the beginning of cutting. to cutting speed, feed, depth of cut, and nose radius of a ceramic cutting tool were examined. Effective approach angle, which is a function of cutting conditions, and boundary area were suggested, and then the influence of those was investigated, The following conclusions were obtained: (1)as cutting speed was increasing. DOC notch wear was decreasing (2) the cutting condition that magnitude of slendermess ratio was made small, was favorable for DOC notch wear, (3) as depth of cut was smaller, the influence of feed on DOC notch wear was also smaller, (4) DOC notch wear was mainly influenced by effective approach angle, but by boundary area in the range of low feed.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.115-123
• /
• 1998

The morphological analysis of wear particle is a very effective means for machine condition monitoring and fault diagnosis. In order to describe morphology of various wear particle, the wear test was carried out under different experimental conditions. And fractal descriptors was applied to boundary and surface of wear particle with image processing system. These descriptors to analyze shape and surface wear particle are shape fractal dimension and surface fractal dimension. The shape fractal dimension can be derived from the boundary profile and surface fractal dimension can be determined by sum of intensity difference of surface pixel. The morphology of wear particles can be effectively obtained by two fractal dimensions.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.30-35
• /
• 2001

The morphological analysis of wear particle is a very effective means for machine condition monitoring and fault diagnosis. In order to describe morphology of various wear particle, the wear test was carried oui under friction experimental conditions. And fractal descriptors was applied to boundary and surface of wear particle with image processing system. These descriptors to analyze shape and surface wear particle are share fractal dimension and surface fractal dimension. The boundry fractal dimension can be derived from the boundary profile and surface fractal dimension can be determined b)r sum of intensity difference of surface pixel. The morphology of wear particles can be effectively obtained by two fractal dimensions.

• Tribology and Lubricants
• /
• v.16 no.6
• /
• pp.477-483
• /
• 2000

Rolling contact fatigue (RCF) tests were performed for two kinds of commercial silicon nitride balls using 4-Ball rolling contact fatigue life tester under EHL condition (Λ=8.9) and boundary lubrication condition (Λ=0.2). All the test balls were finished up to the dimensional accuracy of Grade 5 defined in KS B 2001 (Steel Balls for Ball Bearings) with a size of 8.731 mm. RCF tests were then conducted under the initial theoretical maximum contact stress 6.63 GPa and the spindle speed 10,000 rpm. All the test balls were not failed until 3.75 $\times$ 107 contact cycles and wear tracks of test balls were not conspicuous under EHL condition (Λ= 8.9). In the operations of low lambda regime (Λ= 0.2), all the test balls were surface damaged and high rolling wear resistance was achievable in fully densified using MgO 1 wt% and HIPed balls. Rolling wear of silicon nitride balls under boundary lubrication condition depend mainly on grain size and intergranular phase content of silicon nitride balls.

• Journal of Mechanical Science and Technology
• /
• v.16 no.11
• /
• pp.1428-1434
• /
• 2002

The ball-on-disk type sliding tests with boundary lubricated steels were carried out to verify the effect of initial spacing in surface profiles on wear and scuffing. Three kinds of surface spacing, which are closely related with initial surface micro-cracks on sliding surfaces, were produced on AISI 1045 steel surfaces using different grinding and polishing processes. Frictional forces and time to scuffing were measured, and the shape and amount of wear particles were analyzed to compare the with original surface profiles. From the tests, it was confirmed that the size of wear particles are related closely to the original spacing of the surface profile. The time to failure and amount of wear were sensitive to the surface spacing. The wider surface spacing shows much longer sliding life and smaller amount of wear than the others. Time to scuffing was increased with increasing surface pro(lie spacing. The size of wear particles increased while the wear and wear rate K were decreased with an increase in surface spacing. After the sliding tests, surface cracks of inner parts of the wear track formed due to scuffing were observed and compared among the specimens having the different surface spacing.

• Tribology and Lubricants
• /
• v.17 no.5
• /
• pp.399-405
• /
• 2001

In this paper the ball-on-disk type sliding tests with boundary lubricated steels were carried out to verify the relation between surface profiles and wear as well as scuffing. Three kinds of surface roughness and asperity radius were produced on AISI 1045 steels using the different processes of grinding and polishing. Frictional forces and time to scuffing were measured. Also, the shape and amount of wear particles were analyzed to compare with original profiles. From the tests, it was confirmed that the size of wear particles are very related to original surface profile. The time to failures and wear amounts were sensitive to the surface spacing. The large surface spacing shows much longer sliding life and smaller wear amount than the others. Time to scuffing was increased with increasing surface profile spacing. The sire of wear particles was increased and the amount was decreased with increasing surface profile spacing. Wear volume and wear rate K were decreased with increasing surface profile spacing. And after sliding tests, surface cracks of inner parts of the wear track occurred scuffing were observed and compared the differences about each specimen having the different surface profile spacing.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 2000.06a
• /
• pp.165-177
• /
• 2000

Ceramic on ceramic total hip prostheses are developed to apply to young patients because lifetime of polyethylene joint prostheses is limited by loosening due to biological response. As mating faces of all-ceramic joint must be highly conformed to reduce stress concentration, wear properties of flat surfaces are investigated in this study. Through wear tests at 2 MPa of contact pressure and 36 mm/s of sliding velocity, alumina and silicon carbide keep low wear rate, high hardness and smooth surface. Soft surface film was detected after the test in bovine serum. This suggests that boundary lubrication is effective to reduce wear in all-ceramic joint.

• 제어로봇시스템학회:학술대회논문집
• /
• 1995.10a
• /
• pp.311-314
• /
• 1995

This paper presents a method for measuring tool wear parameters based on two dimensional image information. The tool wear images were obtained from an ITV camera with magnifying and lighting devices, and were analyzed using image processing techniques such as thresholding, noise filtering and boundary tracing. Thresholding was used to transform the captured gray scale image into a binary image for rapid sequential image processing. The threshold level was determined using a novel technique in which the brightness histograms of two concentric windows containing the tool wear image were compared. The use of noise filtering and boundary tracing to reduce the measuring errors was explored. Performance tests of the measurement precision and processing speed revealed that the direct method was highly effective in intermittent tool wear monitoring.