• 한국농공학회지
• /
• 제18권1호
• /
• pp.4071-4078
• /
• 1976

The authors analyzed the seepage by means of the following mathmatical solutions of the Laplace Equations on the given boundary conditions. The boundaries of the flow region are of two types i) impervious boundaries (${\Phi}$=constant), and ii) reservoir boundaries (${\Phi}$=constant). The corresponding w plane, bounding the flow region, is the rectangle in Fig. 8-a. As the z plane and w plane are both polygons, by means of the Schwarz-Christoffel transformation the flow region in each of these planes can be mapped con for mally onto the same half of an auxiliary t plane, there by yielding, say, the functions z=f1(t) and w=f2(t). Then, either by eliminating the variable t or by using t as a parameter, the function w=f(z) can be established.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2001년도 추계 학술대회논문집
• /
• pp.152-156
• /
• 2001

Three dimensional orthogonal grid generation is able to control effectively the grid spacing near the boundaries, but there are some difficulty to meshing complex geometry. The mesh complex geometry by orthogonal grid generation method must divide block of geometry It is required a careful skill, and long time. Its also difficulty to make unstructured mesh on complex geometry. Particularly, three dimensional geometry must have more time and effort. Recently, there have been growing interests in mesh generation of complex grometry, aslike an automobile headlamp, the heart. The method of easily meshing complex geometry is resarched to solve them. We suggest octree grid into one among these methods. As octrce grid is automaticaly adapted at the boundaries by determine the level operations to control the grid spacing near the boundaries are unnecessary. In this paper we showed throe dimensional mesh generation, and heat-flow analysis on the octree mesh.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.326-331
• /
• 2007

Large-scale molecular dynamics simulations are performed to verify the deformation characteristics of grain boundaries in nanolithography process. The copper substrate made of 200,000 atoms is constructed by two grains in different crystal orientations using dynamic relaxation method. The grain boundary is located in the middle of the substrate with $45\sim135$ degree angles. The plowing tip is made of diamond-like-carbon atoms in a variety of shapes. In the simulations, the generation, propagation, and accumulation of dislocations are observed inside the substrate. From the numerical results, we address the dynamic behavior of the grain boundaries as well as the frictional characteristics in terms of the morphology of initial grain boundaries.

• 한국방사선학회논문지
• /
• 제2권2호
• /
• pp.17-21
• /
• 2008

경계면의 고주파 영역을 선명하게 하면 영상의 질이 좋아진다. sobel 연산자를 이용하여 동적 촬영으로 인하여 선명하지 못한 초음파 영상의 결함을 개선시키는 방법을 제안 하고자 한다. 실험 결과 입력 초음파 영상의 경계부분이 선명하게 나타나는 것을 알 수 있었다. 경계부분의 고주파 성분을 강하게 하다 보니 경계부에 인접한 낮은 신호강도 픽셀의 정보를 잃게 되는 점을 보완할 것이 요구된다.

• 로봇학회논문지
• /
• 제4권4호
• /
• pp.281-288
• /
• 2009

Nowadays, many robots have evolved to imitate human social skills such that sociable interaction with humans is possible. Socially interactive robots require abilities different from that of conventional robots. For instance, human-robot interactions are accompanied by emotion similar to human-human interactions. Robot emotional expression is thus very important for humans. This is particularly true for facial expressions, which play an important role in communication amongst other non-verbal forms. In this paper, we introduce a method of creating lifelike facial expressions in robots using variation of affect values which consist of the robot's emotions based on emotional boundaries. The proposed method was examined by experiments of two facial robot simulators.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제27회 춘계학술대회
• /
• pp.139-145
• /
• 1998

This paper addresses the R-curve properties, wear resistance, and erosion resistance of the two silicon carbide ceramics with different microstructures, i.e. , fine grained SiC and in situ-toughened SiC(IST SIC). Fine grained SiC exhibits a relatively flat R-curve behavior whereas the IST SiC exhibits a increasing R-curve behavior. The increasing R-curve behavior in IST SiC is attributed to relatively weak grain boundaries. The rate of material removal during wear tests and erosion tests was higher for IST SiC than that for fine grained SiC. This is attributed to the weaker grain boundaries in IST SiC than that in fine grained SiC. It is implied that fracture toughness in short crack regime should be taken into consideration in the interpretation of the microscopical material removal process. We show that the higher the strength of grain boundaries is, the higher wear and erosion resistances are.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.21-24
• /
• 2000

Ultra-fine grains were produced in pure Al using an Accumulative Rolling-Bonding (ARB) process. After several cycles of the ARB process, pure Al sheets were filled with the ultra-fine grains whose diameters were several hundred nano-meters. With ARB cycles, the nature of grain boundaries of the ultra-fine grains changed from diffusive sub-boundaries to well-defined high angle boundaries. After 7 cycles, ultra-fine polycrystals with large misorientations between neighboring grains were obtained. Sliding wear tests using a pin-on-disk type wear tester were co ducted on the ultra-fine grained pure Al. Wear rates of pure Al increased with the increase of ARB cycle numbers in spite of the increase in hardness. Worn surfaces and cross-sections were examined with optical microscopy (OM) and scanning electron microscopy (SEM) In investigate the wear mechanism of the ultra-fine grained pure Al.

• The Korean Journal of Ceramics
• /
• 제7권2호
• /
• pp.70-73
• /
• 2001

Phase transformation of TiSi$_2$ confined in sub-micron area of which the size is around or smaller than the grain size of C49 TiSi$_2$ phase is studied. It has been known that the C49 to C54 phase change is massive transformation that occurs abruptly starting from C54 nuclei located at triple point grain boundaries of C49 phase. When the C49 phase is confined in sub-micron area, however, the massive phase transformation is observed to be hindered due to the lack of the triple point grain boundaries of C49 phase. Heat treatment at higher temperatures starts to decompose the C49 phase, and the resulting decomposed Ti atoms diffuse to, and react with, the underneath Si material to form C54 phase that exhibits spherical interface with silicon. The newly formed C54 grains can also trigger the massive phase transformation to convert the remaining undecomposed C49 grains to C54 grains by serving as nuclei like conventional C54 nuclei located at triple point grain boundaries.

• Journal of International Society for Simulation Surgery
• /
• 제2권2호
• /
• pp.67-70
• /
• 2015

We propose an automatic vessel segmentation method of vertebral arteries in CT angiography using combined circular and cylindrical model fitting. First, to generate multi-segmented volumes, whole volume is automatically divided into four segments by anatomical properties of bone structures along z-axis of head and neck. To define an optimal volume circumscribing vertebral arteries, anterior-posterior bounding and side boundaries are defined as initial extracted vessel region. Second, the initial vessel candidates are tracked using circular model fitting. Since boundaries of the vertebral arteries are ambiguous in case the arteries pass through the transverse foramen in the cervical vertebra, the circle model is extended along z-axis to cylinder model for considering additional vessel information of neighboring slices. Finally, the boundaries of the vertebral arteries are detected using graph-cut optimization. From the experiments, the proposed method provides accurate results without bone artifacts and eroded vessels in the cervical vertebra.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2002년도 ICCAS
• /
• pp.98.3-98
• /
• 2002

Vision-based systems for finding road lanes have to operate robustly under a wide variety of environ-mental conditions including large amount of scene clutters. This paper presents a method for finding the lane boundaries by combining a local line extraction method and dynamic programming as a search tool. The line extractor obtains an initial position estimation of road lane boundaries from the noisy edge fragments. Dynamic programming then improves the initial approximation to an accurate configuration of lane boundaries. Input image frame is divided into a few sub-regions along the vertical direction. The local line extractor then performs to extract candidate lines of road lanes in the...