• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.3
• /
• pp.581-586
• /
• 2015

This paper has analyzed the variation of subthreshold swing for the ratio of channel length and thickness for asymmetric double gate MOSFET. The asymmetric double gate MOSFET has the advantage that the factors to control the short channel effects increase since top and bottom gate structure can be fabricated differently. The degradation of transport property due to rapid increase of subthreshold swing can be specially reduced in the case of reduction of channel length. However, channel thickness has to be reduced for decrease of channel length from scaling theory. The ratio of channel length vs. thickness becomes the most important factor to determine subthreshold swing. To analyze hermeneutically subthreshold swing, the analytical potential distribution is derived from Poisson's equation, and conduction path and subthreshold swing are calculated for various channel length and thickness. As a result, we know conduction path and subthreshold swing are changed for the ratio of channel length vs. thickness.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.2
• /
• pp.391-396
• /
• 2013

In this paper, for HEVC decoding, an SAO hardware design with less processing time and reduced area is proposed. The proposed SAO hardware architecture introduces the design processing $8{\times}8$ CU to reduce the hardware area and uses internal registers to support $64{\times}64$ CU processing. Instead of previous top-down block partitioning, it uses bottom-up block partitioning to minimize the amount of calculation and processing time. As a result of synthesizing the proposed architecture with TSMC $0.18{\mu}m$ library, the gate area is 30.7k and the maximum frequency is 250MHz. The proposed SAO hardware architecture can process the decode of a macroblock in 64 cycles.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.333.2-333.2
• /
• 2014

RF 스퍼터링 방법을 이용하여 제작된 IGZO 박막 트랜지스터 및 단막을 제조하여 UV처리 유무에 따른 전기적 특성을 평가하였다. IGZO 박막 트랜지스터는 Bottom gate 구조로 제조되었으며 UV처리 이후 전계효과 이동도, 문턱전압 이하 기울기 값등 모든 전기적 특성이 개선된 것을 확인 하였다. 이후 UV처리에 따른 소자의 전기적 특성 개선에 대한 원인을 분석하기위해 물리적, 전기적, 광학적 분석을 실시하였다. XRD분석을 통해 UV처리 유무에 따른 IGZO박막의 물리적 구조 변화를 관찰했지만 IGZO박막은 UV처리 유무에 상관없이 물리적 구조를 갖지 않는 비정질 상태를 보였다. IGZO 박막 트랜지스터의 문턱전압 이하의 기울기 값과을 통하여 반도체 내부에 존재하는 결함의 양을 계산한 결과 UV를 조사하였을 때 결함의 양이 감소하는 결과를 얻었으며 이 결과는 SE를 통해 밴드갭 이하 결함부분을 측정하였을 때와 같은 결과였다. 또한 UV처리 전에는 shallow level defect, deep level defect등의 넓은 준위에서 결함이 발견된 반면 UV처리 이후에는 deep level defect준위는 없어지고 shallow level defect준위 역시 급격하게 감소한 것을 볼 수 있었다. 결과적으로 IGZO 박막의 경우 UV처리를 함에 따라 결함의 양이 감소하여 IGZO박막 트랜지스터의 전계 효과 이동도를 증가 시킬 뿐 아니라 문턱전압 이하 기울기 값을 감소시키는 원인으로 작용하게 된다는 결과를 도출하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.379-379
• /
• 2013

본 논문에서는 Normal ink jetting 공법으로 OTFT를 제작할 때 coffee stain effect에 의해서 반도체 소자의 특성이 저하되는 것을 극복하기 위해서 동일한 위치에 동일한 부피로 Droplet을 형성하는 Multiple ink jetting 공법을 통해 TIPS pentacene 결정의 Morphology와 전기적 특성이 어떻게 변화하는지 알아 보았다. Multiple ink jetting의 drop 횟수가 증가할수록 coffee stain effect에 의해서 형성된 가운데 영역의 Dendrite grain이 점점 작아지다가 7 Drops 이후로는 Big grain 만 남게 되었다. Active layer의 표면 Roughness는 drop 횟수가 증가할수록 낮아지다가 일정 count 이후로는 다시 높아지는 것을 확인할 수 있었다. 전계 이동도(mobility)는 drop 횟수가 증가할수록 커지다가 일정 count 이후로는 saturation되는 것을 확인할 수 있었다. Multiple ink jetting에 의해서 만들어진 OTFT 소자의 전계 이동도(mobility)는 1 drop과 10 drops에서 각각 0.0059, 0.036 cm2/Vs 로 6배 정도 차이가 있었다. 이것은 첫 drop에 의해 만들어진 가운데 Dendrite grain 영역이 Multiple ink jetting을 반복하면서 점점 작아지게 되어 사라지고 두꺼운 Grain 영역만 남게 된 것으로 판단된다. Vth 와 On/Off ratio는 1 drop과 10 drops에서 각각 -3 V, -2 V 그리고 $3.3{\times}10^3$, $1.0{\times}10^4$를 보였다. OTFT의 substrate로 Flexible한 polyethersulfone (PES) 기판을 사용하였고, 절연체로 Spin coating된 Poly-4-vinylphenol (PVP)가 사용되었으며, Gate 및 Source/Drain 전극은 Au를 50 nm 두께로 증착하였다. Channel의 width와 length는 각각 100 um, 40 um 였고, Gate 전극 위에 Active layer를 형성한 Bottom gate 구조로 제작되었다. Ink jet으로 제작된 TIPS pentacene의 결정성은 x-ray diffraction (XRD)와 광학 현미경으로 분석하였고 Thickness profile은 알파스텝 측정기를 이용하였으며, OTFT의 전기적 특성은 Keithley-4,200을 사용하여 측정하였다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.8
• /
• pp.1465-1470
• /
• 2017

In conventional MOSFETs, the silicon thickness is always larger than inversion layer, so that the drain induced barrier lowering (DIBL) is expressed as a function of oxide thickness and channel length regardless of silicon thickness. However, since the silicon thickness is fully depleted in the sub-10 nm low doped double gate (DG) MOSFET, the conventional SPICE model for DIBL is no longer available. Therefore, we propose a novel DIBL SPICE model for DGMOSFETs. In order to analyze this, a thermionic emission and the tunneling current was obtained by the potential and WKB approximation. As a result, it was found that the DIBL was proportional to the sum of the top and bottom oxide thicknesses and the square of the silicon thickness, and inversely proportional to the third power of the channel length. Particularly, static feedback coefficient of SPICE parameter can be used between 1 and 2 as a reasonable parameter.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.2
• /
• pp.230-234
• /
• 1996

A new trenched Hybrid Schottky INjection Field Effect Transistor (HSINFET) is proposed and verified by 2-D semiconductor device simulation. The feature of the proposed structure is that the hybrid Schottky injector is implemented at the trench sidewall and p-n junction injector at the upper sidewall and bottom of a trench. Two-dimensional simulation has been performed to compare the new HSINFET with the SINFET, conventional HSINFET and lateral insulated gate bipolar transistor(LIGBT). The numerical results shows that the current handling capability of the proposed HSINFET is significantly increased without sacrificing turn-off characteristics. The proposed HSINFET exhibits higher latch-up current density and much faster switching speed than the lateral IGBT. The forward voltage drop of the proposed HSINFET is 0.4 V lower than that of the conventional HSINFET and the turn-off time of the trenched HSINFET is much smaller than that of LIGBT.

• Journal of the Korean Vacuum Society
• /
• v.16 no.5
• /
• pp.359-365
• /
• 2007

In this paper we present a bottom-gate type of zinc oxide (ZnO) and Gallium (Ga) doped zinc oxide (GZO) based thin film transistors (TFTs) through applying a radio frequency (RF) magnetron sputtering method at room temperature. The gate leakage current can be reduced up to several ph by applying $SiO_2$ thermally grown instead of using new gate oxide materials. The root mean square (RMS) values of the ZnO and GZO film surface were measured as 1.07 nm and 1.65 nm, respectively. Also, the transmittances of the ZnO and GZO film were more than 80% and 75%, respectively, and they were changed as their film thickness. The ZnO and GZO film had a wurtzite structure that was arranged well as a (002) orientation. The ZnO TFT had a threshold voltage of 2.5 V, a field effect mobility of $0.027\;cm^2/(V{\cdot}s)$, a on/off ratio of $10^4$, a gate voltage swing of 17 V/decade and it operated in a enhancement mode. In case of the GZO TFT, it operated in a depletion mode with a threshold voltage of -3.4 V, a field effect mobility of $0.023\;cm^2/(V{\cdot}s)$, a on/off ratio of $2{\times}10^4$ and a gate voltage swing of 3.3 V/decade. We successfully demonstrated that the TFTs with the enhancement and depletion mode type can be fabricated by using pure ZnO and 1wt% Ga-doped ZnO.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.319-322
• /
• 2003

To match the charge induced by the insulators $CeO_2$ with the remanent polarization of ferro electric SBT thin films, areas of Pt/SBT/Pt (MFM) and those of $Pt/CeO_2/Si$ (MIS) capacitors were ind ependently designed. The area $S_M$ of MIS capacitors to the area $S_F$ of MFM capacitors were varied from 1 to 10, 15, and 20. Top electrode Pt and SBT layers were etched with for various area ratios of $S_M\;/\;S_F$. Bottom electrode Pt and $CeO_2$ layers were respectively deposited by do and rf sputtering in-situ process. SBT thin film were prepared by the metal orgnic decomposition (MOD) technique. $Pt(100nm)/SBT(350nm)/Pt(300nm)/CeO_2(40nm)/p-Si$ (MFMIS) gate structures have been fabricated with the various $S_M\;/\;S_F$ ratios using inductively coupled plasma reactive ion etching (ICP-RIE). The leakage current density of MFMIS gate structures were improved to $6.32{\times}10^{-7}\;A/cm^2$ at the applied gate voltage of 10 V. It is shown that in the memory window increase with the area ratio $S_M\;/\;S_F$ of the MFMIS structures and a larger memory window of 3 V can be obtained for a voltage sweep of ${\pm}9\;V$ for MFMIS structures with an area ratio $S_M\;/\;S_F\;=\;6$ than that of 0.9 V of MFS at the same applied voltage. The maximum memory windows of MFMIS structures were 2.28 V, 3.35 V, and 3.7 V with the are a ratios 1, 2, and 6 at the applied gate voltage of 11 V, respectively. It is concluded that ferroelectric gate capacitors of MFMIS are good candidates for nondestructive readout-nonvolatile memories.

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.3
• /
• pp.73-77
• /
• 2023

In this study, we developed a Multi-level FeRAM (Ferroelectrics random access memory) device utilizing different ferroelectric materials and analyzed its operation through C-V analysis using simulations. To achieve Multi-level operation, we proposed an MFM (Multi-Ferroelectric Material) structure by depositing two different ferroelectric materials with distinct properties horizontally on the same bottom electrode and subsequently adding a gate electrode on top. By analyzing C-V peaks based on the polarization phenomenon occurring under different voltage conditions for the two materials, we confirmed the feasibility of achieving Multi-level operation, where either one or both of the materials can be polarized. Furthermore, we validated the process for implementing the proposed structure using semiconductor fabrication through process simulations. These results signify the significance of the new structure as it allows storing multiple states in a single memory cell, thereby greatly enhancing memory integration.

• Journal of Sensor Science and Technology
• /
• v.7 no.5
• /
• pp.364-371
• /
• 1998

A novel antifuse has been developed for field programmable gate arrays (FPGA's) as a voltage programmable link with Al/$BaTiO_3/SiO_2$/TiW-silicide. The proper program voltage can be obtained by adjusting the deposition thickness of $BaTiO_3$ film. When a negative voltage was applied at bottom TiW-silicide electrode of the antifuse, based on $BaTiO_3(120{\AA})$/$SiO_2(120{\AA})$, the program voltage was about l4.4V and on-resistances were ranged between 40 and $50{\Omega}$. The current-voltage characteristics of antifuses are consistent with a Frenkel-Poole conduction model. However, there are some deviations depending on bias polarity that are probably due to the difference in the interface properties between Al/$BaTiO_3$ and TiW-silicide/$SiO_2$.