• 지질공학
• /
• 제26권1호
• /
• pp.15-22
• /
• 2016

충적 대수층의 수리지질특성 시험을 위한 충적층 공벽 유지장치를 개발하여 변수위법 투수시험(Falling Head Test) 및 순간 충격시험(Slug Test)을 수행하였다. 모래, 자갈을 비롯한 실트층이 주를 이루는 국내 충적층 수리시험은 시험구간의 공벽유지와 시험 중 토사층의 공벽붕괴가 지속적으로 발생하여 투수시험과 순간충격시험 등의 수리시험 수행에 많은 어려움을 겪고 있다. 이에 본 연구는 개공율이 안정적인 필터가 장착된 공벽 유지장치를 시험공에 삽입하여 시험구간 공벽붕괴를 최소화하고 시험시 정확한 단위면적의 산출로 토사층에서의 수리시험 신뢰성을 증대하고자 하였다. 연구결과 기존의 변수위법 투수시험에 의한 투수계수는 8.82 × 10⁻⁵m/sec로 산출되었으며, 동일한 지층, 심도, 시간적인 조건에서 상기 공벽 유지장치 설치 후 투수시험 결과는 4.00 × 10⁻⁴m/sec로 나타나 최대 4.5배 가량의 투수계수 증가현상을 보인다. 이는 시추굴진 중 발생된 세립질의 슬라임이 투수시험 시 시험구간에 피복 또는 충전되어 토사층의 투수성을 저하시키고 시험구간 형성과정에서 최초 원기둥 형태의 시험공벽이 점진적인 붕괴로 인해 토사로 충전되고 시험구간 면적감소에 기인한 현상으로 판단된다. 본 연구는 미고결 충적층의 공벽 유지장치를 현장에 적용하여 시험구간 굴진 시 발생되는 점착력이 낮은 모래, 자갈층의 공벽붕괴에 따른 시험면적 변화가 투수성에 미치는 영향을 평가한 연구로써, 충적 대수층 수리특성 평가의 신뢰성 및 적용성 개선을 위한 기초자료로 활용될 수 있을 것으로 예상된다.

• 지질공학
• /
• 제28권1호
• /
• pp.1-9
• /
• 2018

We propose a borehole test technique to estimate permeability of rocks in borehole. The borehole tests are hydraulic injection tests such as leak-off test and hydraulic fracturing tests, which are originally conducted for stress or casing integrity assessment and not for permeability measurement. We use one-dimensional radial diffusion equation to interpret fluid injection test results in terms of permeability. We apply this technique to a leak-off test conducted at a depth of 700 m in a wellbore, where rock formation is mudstone. The estimated permeability is at an order of $10^{-16}m^2$, which is somewhat high but within the range reported for mudstones previously. Quantitative rick assessment suggests that an accurate measurement of open hole section length is important to improve reliability of results. More data may be needed to ensure the reliability of this technique. If validated, however, this technique can provide cost-effective estimation of in situ permeability without conducting independent permeability tests in borehole.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.427-432
• /
• 2005

This study treats the advantage of in situ line source method measuring the heat transfer capacity of a borehole, using mobile equipment, to determine the thermal properties of the entire borehole system such as thermal conductivity, diffusiveity. volumetric heat capacity, and borehole thermal resistance. The results from the response test include not only the thermal properties of the ground and the borehole, but also conditions that are difficult to estimate, e,g. natural convection in the boreholes, asymmetry in the construction, etc. In this study, 1) theoretical in situ methods for assessing working fluid temperature variation in V-type PE tube have been introduced, and 2) TRTE(Thermal Response Test Equipment) has been built based on these kinds of theoretical in situ methods. Basically TRTE consists of a pump, a heater and temperature sensors for measuring the inlet and outlet temperatures of the borehole. In order to make equipment easily transportable it is set up on a small trailer. Since the response test takes above two days to execute, the test was fully automatic in recording measured data using Labview DAS(Data acquisition system) program. The test was demonstrated in the course of intensive research in this field through the one site at Ulsan city in Korea. From this kind of thermal properties test of borehole systems in situ, the design of the borehole system can be optimized regarding the total geological, hydro-geological and technical conditions at the location.

• 한국태양에너지학회 논문집
• /
• 제29권5호
• /
• pp.20-27
• /
• 2009

The effect of borehole thermal resistance on the borehole length is studied. In performing this work a new concept BLRR(borehole length reduction rate) is developed based on the line source model. The solution of line source model is shown to be valid through the comparison with the data of thermal response test. It is shown that BLRR is a function of soil thermal conductivity(k) and borehole thermal resistance($R_b$). The value of BLRR increases with increasing k, which means reducing $R_b$ is more effective when k is high. The reduction of borehole length with change of $R_b$ is easily estimated with BLRR. The validity of BLRR is also examined with EED analysis.

• 대한기계학회논문집B
• /
• 제30권8호
• /
• pp.764-771
• /
• 2006

Knowledge of ground thermal properties is most important for the proper design of large BHE(borehole heat exchanger) systems. Thermal response tests with mobile measurement devices were first introduced in Sweden and USA in 1995. Thermal response tests have so far been used primarily for in insitu determination of design data for BHE systems, but also for evaluation of grout material, heat exchanger types and ground water effects. The main purpose has been to determine insitu values of effective ground thermal conductivity, including the effect of ground-water flow and natural convection in the boreholes. Test rig is set up on a small trailer, and contains a circulation pump, a heater, temperature sensors and a data logger for recording the temperature data. A constant heat power is injected into the borehole through the pipe system of test rig and the resulting temperature change in the borehole is recorded. The recorded temperature data are analysed with a line-source model, which gives the effective insitu values of rock thermal conductivity and borehole thermal resistance.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2006년도 총회 및 춘계학술발표회
• /
• pp.92-96
• /
• 2006

Borehole geophysical techniques were adopted for characterizing aquifer properties of crystalline rock formation in Bongmyong borehole test site, Kangwon National University. Specific fractures and/or fracture zones accompanying groundwater flow were delineated well by high resolution flowmeter and dilution measurements, and could be confirmed fromconventional well log methods. These geophysical techniques have been proved to be the most effective in aquifer characterization in crystalline rock formation.

• 한국지열·수열에너지학회논문집
• /
• 제8권4호
• /
• pp.32-40
• /
• 2012

Geothermal heat pump(GHP) systems use vertical borehole heat exchangers to transfer heat to and from the surrounding ground via a heat carrier fluid that circulates between the borehole and the heat pump. An Important feature associated with design parameters and system performance is the local thermal resistances between the heat carrier flow channels in the borehole and the surrounding ground. This paper deals with the in-situ experimental determination of the effective thermal properties of the ground. The recorded thermal responses together with the line-source theory are used to determine the thermal conductivity and thermal diffusivity, and the steady-state borehole thermal resistance. In addition, this paper compares the experimental borehole resistance with the results from the different empirical and theoretical relations to evaluate this resistance. Further, the performance simulation of a GHP system with vertical borehole heat exchangers was conducted to analyze the effect of the borehole thermal resistance on the system performance.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.581-586
• /
• 2009

Knowledge of ground thermal properties is most important for the proper design of large scale BHE(borehole heat exchanger) systems. The type, pipe size and thermal performance of the BHE is highly dependent on the ground source heatpump system-efficiency and instruction cost. Thermal response tests with mobile measurement devices were developed primarily for insitu determination of design data for large diameter BHE for triple-U spacer apply. The main purpose has been to determine insitu values of effective ground thermal conductivity and thermal resistance, including the effect of ground-water flow and natural convection in the boreholes. The test rig is set up on a some trailer, and contains a circulation pump, a inline heater, temperature sensors, flow meter, power analysis meter and a data logger for recording the temperature, fluid flow data. A constant heat power is injected into the borehole through the tripl-U pipes system of test rig and the resulting temperature change in the borehole is recorded. The recorded temperature data are analysed with a line-source model, which gives the effective insitu values of rock thermal conductivity and borehole thermal resistance of large diameter BHE for spacer apply.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.768-776
• /
• 2006

Recently in spite of Development of Investigation machine, in Application of Geotechnical Properties by empirical recommendation to the Slope Stability Analysis. It is generally Application of convenience and conservative Geotechnical Properties by Borehole Shear Test(BST) in Representative Zone that Non-Division of Increase as the depth of Strength Parameters In Deep Weathered Zone. Therefore, it is become environment pollution and Non-Economical Slope Design to Application of convenience and conservative Geotechnical Properties. The production mechanism of Deep Weathered Zone is tend to Weathering Degree low and Strength increase by increase as the depth. it is realistic design that Division of Deep Weathered Zone and application Geotechnical Properties of Each Layer. In this Paper, Determined The Relationship of Strength Parameters between Standard Penetration Test(SPT), Borehole Shear Test(BST) and empirical recommendation also Applyed each strength parameters of divided zone to the Slope Stability Analysis by continuous Borehole Shear Test(BST) in Deep Weathered Zone during design of The 2nd Bridge Connection Road of Incheon International Airport.

• 화약ㆍ발파
• /
• 제28권2호
• /
• pp.37-49
• /
• 2010

도심지 특성상 주변구조물에 근접한 발파로 발생되는 지반진동은 인체에 간접피해와 구조물에 물적피해를 줄 수 있다. 설계단계 또는 시공 전 민원발생 시 구조물의 피해정도를 평가하는 방법으로는 단순 진동파형을 정량적으로 표현하는데 가장 접근성이 좋은 시추공 발파시험이 주로 이용되고 있다. 본 연구는 소량의 폭약으로 인위적인 진동에너지를 발생시키는 발파시험에 전자뇌관 기폭시스템을 처음 적용하였다. 전기뇌관 시추공 발파와 전자뇌관 시추공발파의 뇌관 지연시차 상관관계, 시험장소의 터널본선과 유사 암층에 시설된 구조물에서 측정한 PPV와 서로 다른 매개 층을 포함한 터널상부 지상도로에서 측정한 PPV의 상관관계, 기존 연구결과 얻어진 시추공발파 및 터널발파 PPV와의 상관관계를 비교 분석하여 시추공 발파의 유용성과 뇌관 지연시차의 중요성을 언급하고자 한다.