The recycled washwater, which has different water quality and is produced about 5 to 20% of the total water volume treated, affects the unit operation of water treatment, especially coagulation process. However, the effects of recycled washwater on unit operation of water treatment have not been fully investigated. In this study, effects of recycled washwater on coagulation process were investigated to find the optimum coagulation condition by analyzing turbidity, $UV_{254}$, TOC removal efficiencies. In addition, effects of recycled washwater on residual Al after coagulation were studied by analyzing soluble and particulate Al. The size distribution and fractal dimension of coagulated also analyzed. The recycled washwater was lower pH than the raw water. And the recycled washwater had higher $UV_{254}$, TOC and residual Al concentration than the raw water. Residual Al concentration of recycled washwater was about 50 times higher than that of raw water. Optimum coagulant dosages on the blending recycled washwater and the raw water for turbidity, $UV_{254}$ and Al removal were lower than that on the raw water. However, TOC removal increased by increasing coagulant dosage. The size and fractal dimension of coagulated particle produced in the blending recycled washwater were larger, which imply faster settling velocity, than those produced in the raw water only.
While trains perform a complete precision stopping control at stop point, it is essential to keep better commuters comfort in prompt. Because a train's brake force tends to increase a brake effort in a low speed and a low brake effort, a brake force in motor cars must be increased to keep better passenger comfort, to control the special braking qua1ities and to prevent the impact of the automatic coupler rather than trailer's, Rail cars must have a special braking process for the train stopping control. In the train stop mode, the train stopping control is designed to start at 20km/h. It starts by Dynamic brake blending, and then finally stops by only the friction. If these process are not exactly activated, the train may fail a complete precision stop. In this report, it studied the electric and friction brake processing during the precious stopping control. To achieve exact test results, the speed reference has to be reduced the calculated difference. In the precision stopping control. the ways of the keeping brake force in motor car was analyzed and some solutions of controling air pressure was brought up by means of direct test in main line, This study was based on line 5 in Seoul Metropolitan subway.
Study has been made for producing anionic surfactant using waste fleshing scraps from the leather making process through refining, esterification, sulfonation and blending processes. As a most optimum lard oil refining method, refining was carried out for 4 hours under temperature of $120^{\circ}C$ and approximately 200 mbar vacuum, which gave a recovery of more than 80% lard oil. Refined lard oil obtained thus was undergone methlyl-esterification, then sulfonated to make a degreasing agent. By methyl-esterification using lard oil, more than 85% of fatty acid and $12{\sim}13%$ of glycerine were extracted from the oil. Sulfonation of the extracted fatty acid ester lard oil has shown most optimum at $15{\sim}20%$ chlorosulfonic acid content, and the content of bonding sulfate at this time was higher than 3.5%. Finally the followed anionic surfactant having degreasing force of 80% and higher could be made by blending process.
한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
/
pp.706-707
/
2006
Premixes treated with a binder, such as in the FLOMET process, exhibit better flow, reduced dusting and segregation and improved productivity and part consistency compared to conventional premixes. The binder treatment is highly suitable for high performance P/M applications which often require premixes containing very fine alloying additives and excellent die filling characteristics. With this process, various binders and lubricants can be utilized in order to make premixes with unique properties. In this paper, the characteristics and performances of bonded premixes are reported.
Rohe, Thomas;Koelle, Sabine;Becker, Wolfgang;Eisenreich, Norbert;Eyerer, Peter
한국근적외분광분석학회:학술대회논문집
/
한국근적외분광분석학회 2001년도 NIR-2001
/
pp.1082-1082
/
2001
Extrusion is one of the most important processes in polymer industry. The characterization of the polymer melt during processing will improve this process noticeably, One possibility of characterizing the actual processed polymer melt is the inline near infrared (NIR) spectroscopy, With this method several polymer properties can be observed during processing, e.g. composition, moisture ormechanical properties of the melt. For this purpose probes for transmission and reflection measurements have been developed, withstanding the high temperatures and pressures appearing during extrusion process (tested up to 300$^{\circ}C$ and 10 ㎫). For the transmission system an optical bypass was developed to eliminate disturbing spectral influences and hence increase the long term stability, which is the prerequisite for an industrial application. Measurements in transmission and reflection produced comparable results (or blending processes, where the prediction error was less than 1%. An optimum RMSEP of only 0.24% was found for preprocessed polymer blends measured in transmission on a laboratory extruder. A transflection measurement allowed for the first time the recording of relevant NIR-spectra in the screw area of an extruder. The application to a (PE+PP) blending process delivered promising results. This new measurement mode allows the observation of the ongoing processes within the screw area, which is of maximum Interest for reactive extrusion processes. Due to economic reasons the calibration transfer between different extrusion systems is also of high importance. Investigations on simulated and real-world spectra showed that a calibration transfer is possible. A new method alternatively to the well-known direct standardization procedures was developed, which is based on an automatic data pretreatment. This procedure delivers comparable results for the calibration transfer. Overall this paper presents concepts, components and algorithms for the inline near infrared (NIR) spectroscopy for polymer extrusion, which allows the use of it in a real industrial extrusion process.
The reconstituted tobacco leaves(RTL) playa major part in the control of the low density and tar cigarette. Reconstituted tobacco manufactured by the papermaking process has much higher filling power than homogenized tobacco manufactured by slurry and rolling process. Fragile reconstituted tobaccos are liable to lead to small particles detrimental for filling power so they must be properly flexible. This work was conducted to determine the effect of CaCO$_3$ addition in paper-making process on the filling power and the flexibility of the reconstituted tobacco and to obtain the fundamental informations for improving the quality of domestic reconstituted tobacco. We analyzed the wood fiber species, the filler level, the fiber length, the fineness level and observed the surface of the RTL. From the obtained results, we could determine that foreign reconstituted tobacco was manufactured by blending softwood with hardwood and over 8% of calcium carbonate at the addition level. The domestic RTL has much higher fine fiber level by 23.2 % than that of foreign, so the refining treatment process and the condition must be reoptimized for the improvement of RTL quality.
사과를 이용한 반고형 이유보충식을 개발하고자 사과퓨레의 다양한 제조조건에 따른 갈변정도와 이화학적 특성, ascorbic acid 첨가에 의한 갈변억제 효과를 살펴보고, 레토르트 이유보충식의 제조 가능성을 알아보았다. 사과퓨레의 점도는 $2,600{\sim}5,856\;cp$였으며, 펙틴의 주골격인 무수갈락투론산은 $4.15{\sim}11.92\;mg%$이고 측쇄인 중성당은 $6.18{\sim}10.65\;mg%$였다. 유리당은 fructose$(5.43{\sim}8.87%)$, glucose$(2.11{\sim}4.23%)$, sucrose$(1.64{\sim}2.94%)$을 함유하고 있었다. Ascorbic acid 함량은 $1.54{\sim}1.83\;mg%$로 퓨레 제조과정에서 열처리에 의해 상당량이 파괴된 것으로 생각된다. 사과퓨레 제조시 열처리를 하지 않고 blending 후 가열하는 방법(A)은 상대적으로 L값이 낮고 적색도 a값이 높고 외관상으로도 갈변이 많이 진행되었지만 관능특성과 이화학적 특성면에서는 높은 평가를 받아 갈변현상을 효과적으로 억제할 필요성이 대두되었다. Steaming 후 blending하여 가열하는 방법(B)은 전체적인 선호도에서 높은 평가를 받았다. Blanching 후 blending하여 가열하는 방법(C)는 영양소 함량과 질감 및 맛에 대한 관능평가에서 상대적으로 떨어져서 다음 단계의 실험에서 제외되었다. 이를 보완하기 위해 갈변억제제로 sodium ascorbic acid를 사과퓨레의 제조시 침지과정(1), blending 과정(2), 가열 과정(3), blending 및 가열 과정(4)에 각각 첨가하였을 때, 사과퓨레 제조방법 A와 B 모두에서 첨가방법 2가 상대적으로 갈변억제 효과가 컸다. 색의 선호도 조사에서 가장 높은 평가를 받은 제조방법 B-첨가방법 2를 사과 이유보충식의 제조법으로 채택하고 살균 전후의 이화학적 특성과 관능특성을 비교하였다. 레토르트 살균 후 점도는 3,477 cp에서 2,294 cp로 감소하였고, 수용성 비타민에서 thiamin은 완전히 파괴되었으며 riboflavin은 41%, ascorbic acid는 21% 감소하였다. 그러나 레토르트 살균이 유리당과 유리 아미노산의 함량 그리고 관능특성에는 큰 영향을 주지 않아 사과를 steaming하고, sodium ascorbic acid를 blending 과정에서 첨가하는 방법이 레토르트 사과 이유보충식의 제조법으로 적합한 것으로 평가되었다.
In this study, lignin/chlorinated poly(vinyl chloride)(CPVC) blended fibers have been produced for the development of low-cost carbon fiber. Carbon fiber manufacturing was accomplished through stabilization and carbonization process. The lignin/CPVC blended fibers were prepared by wet spinning method. Dimethylacetamid e(DMAc) and cychlohexanone in a ratio of 5:1(wt%) was employed as co-solvent. The ratio of lignin/CPVC was prepared at 0/10, 1/9, 2/8, 3/7, 4/6, and 5/5(wt%). The spinning solution was extruded at a rate of 0.1 to 0.4ml/min according to the blending ratio. The speed of the rollers was the same for all ratios(draw ratio=1). Analysis of fiber cross-section by scanning eletron microscopy(SEM) showed that as the lignin ratio increased in the same coagulation bath and distilled water, the pore size of the spinning fiber decreased. Therefore, the highest tensile strength of the blending fibers was 6.3±1.2MPa at the 5/5 ratio. The carbon fiber also showed the best tensile strength of 120.78±2.43MPa at 5/5 ratio.
In the previous work, the effect of blending with two kinds of low density polyethylene (LDPE) on physical and electrical properties have been investigated. From the results, blending with two kinds of LDPE was effective method on changing the morphology of LDPE and improving the high-field characteristics in high temperature region. Especially, it suggested that the F$\_$BImp/ was associated with the changes of the crystal size. In this work, the relationship between the morphology and the high-field characteristics of blended LDPE was discussed. In addition, the physical and electrical properties of blended LDPE with extrusion treatment were investigated. The two groups of specimen were prepared; Group 1 was prepared by passing 1 time through the extruder included in the film-blowing process, and Group 2 was prepared by passing 2 times through the extruder. From the relation between the crystal size which was perpendicular to the (020) plane and the F$\_$BImp/ of blended LDPE, it was confirmed that the F$\_$BImp/ was associated with the changes of crystal size due to the blending. Moreover, the F$\_$BImp/ of blended LDPE in Group 2 was higher than that of blended LDPE in Group 1. The crystal size of the (020) plane became smaller according to the extrusion treatment. These results suggest that the uniform distribution and dispersion of crystalline occurred due to the extrusion treatment and the morphological change due to the extrusion treatment influenced on the electrical properties of blended LDPE.
The aim of this study is to develop a simple and rapid field method for the determination of chloride content in tobacco green or cured leaves. To set up a practical process, several factors such as the proper sampling position of each leaf, the size of leaf lamina pieces for blending, the substitution of deionized water fur the extracting solution, 0.1N $HNO_3$, the submerging durations before blending, and the standing times before measuring were studied using flue-cured and burley tobacco with a stable and reproducible Chloride Meter, KRK CL-2Z. From the results, chloride contents of tobacco leaves could be analyzed with the Chloride Meter(CL-2Z) using the suspension of 14 mm diameter leaf disks after soaking in distilled water for 30 min., blending with a mini-blender for 30 seconds. The chloride contents measured in this way showed highly significant correlations with ones by the conventional potentiometric method using an ion meter-chloride electrode and $AgNO_3$ titration. In our method, the procedures such as drying, powdering and weighing samples, and using chemical reagents for extraction (0.1N $HNO_3$) and titration(0.028N $AgNO_3$) could be eliminated. These results suggest that the newly constructed method using the Chloride Meter is more efficient to determine the chloride content of tobacco leave in comparison with the one by the Ion $Meter:AgNO_3$ titration.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.