• 한국자동차공학회논문집
• /
• 제18권5호
• /
• pp.76-84
• /
• 2010

The aim of this study is to analyze the effect of the ethanol blending in diesel-ethanol blended fuels on the spray and combustion characteristics in a common-rail four-cylinder diesel engine. For the analysis of the spray characteristics, the spray images were obtained using a high speed camera with metal-halide lamps. From these spray images, the macroscopic spray characteristics such as the spray tip penetration and spray cone angle were investigated. Also, the combustion characteristics including the combustion pressure and the rate of heat release were studied with the analysis of the exhaust emissions in diesel-ethanol blended fuel driven diesel engine. It can be confirmed from the experiment on spray characteristics of diesel-ethanol blended fuels that the increased ethanol blending ratio induced the decrease of the spray tip penetration after the end of the injection. The spray cone angle slightly increased by the blending of ethanol fuel. In the experiment on atomization characteristics, the ethanol blending caused the improvement of the diesel atomization performance. On the other hand, at the same engine load condition, the increase of the ethanol blending ratio lead to lengthen the ignition delays, and to decrease the peak combustion pressure and the rate of heat release. Totally, the combustion and emission characteristics of ULSD and DE10 showed similar characteristics. However, in the case of DE20, CO and HC rapidly increased, and $NO_x$ decreased. It can be believed that 20% ethanol disturbed the combustion of diesel-ethanol blended fuel due to the low cetane number and evaporation.

• 한국의류학회지
• /
• 제31권7호
• /
• pp.1119-1127
• /
• 2007

Nonwovens have been widely used in various regions from the households to the industrial, agricultural and medical goods. Synthetic fibers have been used for source of nonwovens commonly because of their useful and economic properties. They are not only main factor causing environmental problems but also spend huge cost to renew the environmental disruption by them. Nonwovens must have both cost-competitiveness and environment-friendly property to be the desirable sources in 21th centuries. For meet these needs, it is suitable for the times that economical and environmentally-safe kenaf fibers would be used as raw materials of nonwovens. Kenaf and polyester fibers were blended in 4 types of ratio : 0/100, 20/80, 40/60, 60/40 were needle-punched. The nonwovens properties such as color values, surface appearance, strength, elongations, stiffness, moisture regain, water and oil absorbency, and electrification were tested. As the results, tensile and tear strengths, water and oil absorbency were maximum at 20/80 kenaf/polyester blend nonwoven, because of effecting by nonwoven structure and fiber properties. The moisture regain were increased according to kenaf were blended and the eletrification reduced in proportion to the kenaf fibers by chemical property of fiber composed nonwovens.

• 자원리싸이클링
• /
• 제15권2호
• /
• pp.24-31
• /
• 2006

폐콘크리트 파쇄시 발생하는 재생잔골재의 품질을 검토하였으며, 재생잔골재를 활용한 모르타르의 압축강도, 휨강도 및 흡수율을 검토하였다. 또한, 프리캐스트 콘크리트 제품용 골재로서의 적용성에 대하여 평가하였다. 재생잔골재의 밀도 및 흡수율은 각각 $2.31\;g/cm^3$ 및 8.07%로 KS F 2573의 2종에 해당되는 품질이었다. 혼합시멘트 MRS1, MRS2 및 MRS3 사용 모르타르의 재령 28일 압축강도는 물-시멘트비 35%, 양생온도 $40^{\circ}C$의 조건에서 각각 15.8, 27.4 및 48.7MPa로 최대값을 발현하였다. 모르타르의 최대휨강도는 혼합시멘트 MRS1 및 MRS2 사용시 물-시멘트비 35.0%, 양생온도 $40^{\circ}C$, 혼합시멘트 MRS3사용시 물-시멘트비 37.5%, 양생온도 $40^{\circ}C$의 조건에서 발현하였다. 혼합시멘트 MRS1, MRS2 및 MRS3를 사용한 모르타르의 흡수율의 범위는 각각 $8.3{\sim}7.3%,\;6.5{\sim}8.5%$ 및 $3.5{\sim}6%$의 범위로 나타났다. 그러므로 혼합시멘트와 재생잔골재의 비율을 적절히 조절함으로써 MRS1는 저강도용, MRS2는 보통강도용, MRS3는 고강도용으로 다양한 프리캐스트 콘크리트 제품에 적용될 수 있을 것으로 기대된다.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제9권6호
• /
• pp.693-704
• /
• 2017

Blended-Wing-Body Underwater Glider (BWBUG), which has excellent hydrodynamic performance, is a new kind of underwater glider in recent years. In the shape optimization of BWBUG, the lift to drag ratio is often used as the optimization target. However this results in lose of internal space. In this paper, the energy reserve is defined as the direct proportional function of the internal space of BWBUG. A motion model, which relates gliding range to steady gliding motion parameters as well as energy consumption, is established by analyzing the steady-state gliding motion. The maximum gliding range is used as the optimization target instead of the lift to drag ratio to optimizing the shape of BWBUG. The result of optimization shows that the maximum gliding range of initial design is increased by 32.1% though an Efficient Global Optimization (EGO) process.

• 한국자동차공학회논문집
• /
• 제22권4호
• /
• pp.55-64
• /
• 2014

This work was investigated on pilot injection strategy of blended fuels(Diesel-DME) for combustion and emissions in a single cylinder direct injection compression ignition engine. Diesel and DME were blended by the method of weight ratio. Weight ratios for diesel and DME were 95:05 and 90:10 respectively. dSOI between main and pilot injection timing was varied. A total amount of injected fuels(single injection) was adjusted to obtain the fixed BMEP as 4.2 bar in order to compare with the fuel conditions. Also, the amount of pilot injection fuel was varied by 5%, 10% and 20% of total injection fuel. The engine was equipped with common rail and injection pressure is 700 bar at 1200 rpm. As a result, when mixing ratio increase, indicated thermal efficiency was increased in comparison with DD 100 and CO, THC and smoke were lower than DD 100. The influence of reducing NOx by pilot injection was more effective than DD 100. When pilot injection quantity increase, abrupt increase of NOx was occured at pilot injection quantity of 20%.

• 한국분무공학회지
• /
• 제25권3호
• /
• pp.111-118
• /
• 2020

This paper describes the effect of DME, biodiesel blended fuels on the macroscopic spray characteristics in a high pressure diesel injection system using Background Oriented Schlieren (BOS) method. The BOS method for visualization of impingement evaporation sprays to analyze macroscopic spray properties and evolutionary processes. In this work, the blending ratio of DME in the blended fuel are 0, 50, 100% by weight ratio. In order to investigate the macroscopic impinged spray characteristics under the various injection parameters and blending ratio. In this work, a mini-sac type single-hole nozzle injector with nozzle hole was length 0.7 mm and diameter of 0.3 mm was used. According to the result, the spray area of the collision wall increased as the DME mixing ratio increased, and the evolutionary pattern showed a stepwise increase due to the collision effect of the wall. Also, results of impinged spray area were increased according to increasing injection pressure.

• 한국염색가공학회지
• /
• 제32권2호
• /
• pp.111-120
• /
• 2020

In this study, lignin/chlorinated poly(vinyl chloride)(CPVC) blended fibers have been produced for the development of low-cost carbon fiber. Carbon fiber manufacturing was accomplished through stabilization and carbonization process. The lignin/CPVC blended fibers were prepared by wet spinning method. Dimethylacetamid e(DMAc) and cychlohexanone in a ratio of 5:1(wt%) was employed as co-solvent. The ratio of lignin/CPVC was prepared at 0/10, 1/9, 2/8, 3/7, 4/6, and 5/5(wt%). The spinning solution was extruded at a rate of 0.1 to 0.4ml/min according to the blending ratio. The speed of the rollers was the same for all ratios(draw ratio=1). Analysis of fiber cross-section by scanning eletron microscopy(SEM) showed that as the lignin ratio increased in the same coagulation bath and distilled water, the pore size of the spinning fiber decreased. Therefore, the highest tensile strength of the blending fibers was 6.3±1.2MPa at the 5/5 ratio. The carbon fiber also showed the best tensile strength of 120.78±2.43MPa at 5/5 ratio.

• 한국건축시공학회지
• /
• 제12권1호
• /
• pp.73-86
• /
• 2012

In this research, the possible applicability of mixture blended with natural, crushed, and recycled fine aggregate are discussed. The fresh and hardened properties of mortar using blended fine aggregates are monitored depending on various blending ratio of fine aggregates. Newly developed ternary diagram was also utilized for better interpretation of the data. It was found that air content increased and unit weight decreased as recycled fine aggregate content increased. With moisture type processing of recycled fine aggregate, the mortar flow was not negatively affected by increase in the recycled fine aggregate content. The ternary diagram is found to be an effective graphical presentation tool that can be used for the quality evaluation of mortar using blended fine aggregate.

• 한국분무공학회지
• /
• 제17권4호
• /
• pp.178-184
• /
• 2012

The aim of this study was to compare the spray characteristics of a typical fuel (100% diesel, DME) and diesel-DME blended fuel in a constant volume combustion chamber (CVCC). The typical fuel (100% diesel, DME) and diesel-DME blended fuel spray characteristics were investigated at various ambient pressures (pressurized nitrogen) and fuel injection pressures using a common rail fuel injection system when the fuel mixture ratio was varied. The fuel injection quantity and spray characteristics were measured including spray shape, penetration length, and spray angle. Common types of injectors were used.

• Journal of the Korean Data and Information Science Society
• /
• 제17권2호
• /
• pp.543-557
• /
• 2006

This paper is concerned with the applicability of the chi-square approximation to the six disparity statistics: the Pearson chi-square, the generalized likelihood ratio, the power divergence, the blended weight chi-square, the blended weight Hellinger distance, and the negative exponential disparity statistic. Three dimensional contingency tables of small and moderate sample sizes are generated to be fitted to all possible hierarchical log-linear models: the completely independent model, the conditionally independent model, the partial association models, and the model with one variable independent of the other two. For models with direct solutions of expected cell counts, point estimates and confidence intervals of the 90 and 95 percentage points of six statistics are explored. For model without direct solutions, the empirical significant levels and the empirical powers of six statistics to test the significance of the three factor interaction are computed and compared.