• Transactions of the Korean hydrogen and new energy society
• /
• 제31권4호
• /
• pp.387-394
• /
• 2020

A parametric study of a 2.5 kW class propeller type micro hydraulic turbine was performed. In order to analyze the internal flow characteristics in the hydraulic turbine, three dimensional Reynolds-averaged Navier-Stokes equations with shear stress transport turbulence model were used and the hexahedral grid system was used to construct computational domain. To secure the reliability of the numerical analysis, the grid dependency test was performed using the grid convergence index method based on the Richardson extrapolation, and the grid dependency was removed when about 1.7 million nodes were used. For the parametric study, the axial distance at shroud span (L) between the inlet guide vane and the runner, and the inlet and outlet blade angles (β₁, β₂) of the runner were selected as the geometric parameters. The inlet and outlet angles of the runner were defined in the 3 spans from the hub to tip, and a total of 7 geometric parameters were investigated. It was confirmed that the outlet angles of the runner had the most sensitive effect on the power and efficiency of the micro hydraulic turbine.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• 제38권9호
• /
• pp.943-954
• /
• 2010

In this study, a radial inflow type turbine was applied and the outer diameter of the turbine rotor was 108 mm. The turbine blade on a circular plate disc was designed as an axial-type because its partial admission rate was 1.4-4.1%. The turbine consisted of three stages. The performance test has been conducted with various admission rates, tip clearances and nozzle flow angles. The turbine output power was measured on each stage. The turbine performance was obtained in a wide rotational speed range in order to compare its performance according to various operating conditions. The net specific output torque was also measured to compare its overall performance. Computational analysis was conducted for predicting turbine performance. The computed results were in good agreement with the experimental results.

• Journal of Biosystems Engineering
• /
• 제31권4호
• /
• pp.342-348
• /
• 2006

Aerial application using an unmanned agricultural helicopter became necessary for both labor saving and timely spraying. In the previous paper, a rotor system was developed and lift capability was evaluated. The experimental results were compared with simulated predictions using the CFD-ACE program. From the simulation, the relative velocity on the top surface of the blade airfoil increased, resulting in the pressure drop. The CFD analyses were revealed that a drag resistance on the leading edge of the airfoil, a wake at the trailing edge, and a positive pressure underneath the bottom surface were observed. As the results of the simulation, total lifts of 56.8, 74.4 and $95.0kg_f$ were obtained at the 6, 8 and $10^{\circ}$ of AAT (angle of attack), respectively. The simulation results agreed reasonably up to $10^{\circ}$ of AAT. However, at a greater AAT $(<12^{\circ})$ the simulated total lift continuously increased to $105kg_f$, comparing with a decreasing experimental total lift due to the lack of engine power. At a stiff angle of $18^{\circ}$ AAT, a wake was observed at the trailing edge of the airfoil. A rated operating condition determined from the previous paper was also verified through the simulation.

• Journal of Biosystems Engineering
• /
• 제32권5호
• /
• pp.292-300
• /
• 2007

Not many types of roughage cutters have been introduced in Korea so far. However, those machines could not satisfy farmers to cut rice straw or barley wrap-silage properly. Stiffness and firmness of roughage bale were two obstructing factors. In order to solve this problem, a tractor attached cut-feeding machinery for the round baled roughage was developed for dairy and beef cattle farm in Korea. A series of tests were performed and acquired data were analyzed by using the several imported roughage cutters, which have been already introduced in dairy farm in Korea. And, a prototype of forage cutter was selected, analyzed, designed and manufactured to develop a tractor attached roughage cut-feeder for round bale. Also, the prototype machine was tested, modified and improved through revising model. As a result, a tractor attached roughage cut-feeder for round bale was manufactured. In order to evaluate the performance of the model machinery. a series of test were performed by the prototype machinery both at the plant and field. The model machinery developed satisfied in both power requirement and cutting capacity. As a conclusion, one of the obstacles against feeding the round baled roughage in the korea cattle farm can be eliminated by developing the tractor attached round baled roughage cut-feeder.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 한국추진공학회 2005년도 제25회 추계학술대회논문집
• /
• pp.34-39
• /
• 2005

In this study, 3-D nozzle shape and the shape of nozzle at exit plane were adopted as design parameter of 3-D supersonic nozzle and numerical analyses for these parameters have been performed to investigate the flow and performance characteristics for design parameters of the turbine. Firstly, comparing results for nozzle shape, rectangular nozzle had less total pressure loss occurred in axial gap and more power by 1.5% than circular nozzle did. Next, comparing the results for the shape of nozzle at exit plane, it is found that the performance of partial admission turbine was largely depended upon the gap between nozzle wall at exit plane and the hub / tip of rotor blade and the length between nozzles.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• 제40권5호
• /
• pp.321-327
• /
• 2016

This paper presents the application of airfoil impeller for enhancement of aerodynamic performance of a high speed centrifugal fan. Three airfoil impellers are proposed, considering the maximum thickness and the location of maximum thickness of the airfoil. C4 airfoil thickness distribution is applied to the three airfoil impellers. The impellers are evaluated using CFD (computational fluid dynamics) and suction power test. From the results, it is confirmed that flow separations on the pressure side of the impeller blades and the pressure side of diffuser blades are reduced when airfoil blade is applied to the impellers. It is also confirmed that with the centrifugal fan having airfoil impellers, there is an increase in fan efficiency by approximately 3% and reduction in specific sound level by approximately 1.3 dB(A).

• Journal of Mechanical Science and Technology
• /
• 제18권2호
• /
• pp.185-192
• /
• 2004

The aeroacoustic characteristics of a centrifugal fan for a vacuum cleaner and its noise reduction method are studied in this paper. The major noise source of a vacuum cleaner is the centrifugal fan. The impeller of the fan rotates at over 30000 rpm, and generates very high-level noise. It was revealed that the dominant noise source is the aerodynamic interaction between the rotating impeller and stationary diffuser. The directivity of acoustic pressure showed that most of the noise propagates backward direction of the fan-motor assembly. In order to reduce the high tonal sound generated from the aerodynamic interaction, unevenly pitched impeller and diffuser, and tapered impeller designs were proposed and experiments were performed. Uneven pitch design of the impeller changes the sound quality while the overall sound power level (SPL) and the performance remains similar. The effect of the tapered design of impeller was evaluated. The trailing edge of the tapered fan is inclined. This reduces the flow interaction between the rotating impeller and the stationary diffuser because of some phase shifts. The static efficiency of the new impeller design is slightly lower than the previous design. However, the overall SPL is reduced by about 4 dB(A). The SPL of the fundamental blade passing frequency (BPF) is reduced by about 6 dB (A) and the 2$\^$nd/ BPF is reduced about 20 dB (A). The vacuum cleaner with the tapered impeller design produces lower noise level than the previous one, and the strong tonal sound was dramatically reduced.

• Journal of Ocean Engineering and Technology
• /
• 제32권3호
• /
• pp.202-207
• /
• 2018

This paper presents the efficiency of a floating vertical axis wind turbine with variable-pitch. A model was designed to use the lift force and drag force for blades with various pitch angles. The blade's pitch angle is controlled by the stopper. To validate the efficiency of the wind turbine discussed in this paper, a model test was carried out through a single model efficiency experiment and wave tank experiment. The parameters of the single model efficiency experiment were the wind speed, electronic load, and pitch angle. The wave tank experiment was performed using the most efficient pitch angle from the results of the single model efficiency experiment. According to the results of the wave tank experiment, the surge and pitch motion of a structure slightly affect the efficiency of a wind turbine, but the heave motion has a large effect because the heights of the wind turbine and wind generator are almost the same.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권10호
• /
• pp.1244-1250
• /
• 2014

The temperature of the main engine cabin of commercial vessel is very high. The material SS-316L undergoes creep damage at temperatures exceeding $450^{\circ}C$. It is essential to maintain the highly stressed engine cabin below the creep regime. Hence, seawater is employed in this kind of maritime vehicles as cooling liquid. It obtains the thermal energy at the cooling pipe line after passing through main engine cooling system. To harness the energy in the seawater, a turbine can be installed to absorb the energy in the seawater before being released into the sea. In this study, a cooling pipe line is selected to apply the tubular type hydro turbine for transferring the energy. Numerical analysis for investigating the performance and the internal flow characteristics of the tubular turbine is conducted. The results show that the maximum efficiency of 85.8% is achieved although the efficiency drops rapidly at partial flow rate condition. The efficiency descends slowly at the condition of excess flow rate. There is a relatively wide operating range of flow rate of this turbine to keep high efficiency at the excess flow rate condition. For the internal flow of the turbine, there is uniform streamline on the suction and pressure sides of the blade at the design point. However, the secondary flow appears at the suction and pressure sidesat the excess flow rate.In addition, it appears only at pressure side at the partial flow rate condition.

• Journal of Advanced Marine Engineering and Technology
• /
• 제35권2호
• /
• pp.175-181
• /
• 2011

The purpose of this study is to secure the design data for the optimization of the radial turbine and heat cycle system, by using the CFD analysis technique and the design of 100kW class radial turbine applicable to waste heat recovery generation system for ship. Radial turbine was comprised of scroll casing, vane nozzle with 18 blades and rotor with 13 blades, and analysis grid was used to about 2.3 million. Mass flow rate and rotational speed was 0.5kg/s, 75,0000rpm, respectively. Eight kinds of inlet pressure was set between 195 and 620kPa. As the flow accelerated through the nozzle passage to the throat, the pressure level at the pressure and suction sides becomed similar to about Mach number of 0.35. When the inlet temperature and pressure was $250^{\circ}C$, 352kPa respectively, the isentropic efficiency and mechanical power showed the analysis results of 74% and 108kW.