• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.485-490
• /
• 2004

Sawtooth mixing device used in a non-premixed burner is evaluated for flame stabilization and NO$_{x}$ reduction. Three mixers with different blade angles are tested. Methane is delivered through the fuel jet and air passes through the co-flow annulus. The flame mode changes (attached flame, lifted flame and extinction) against the fuel flow speed are measured, and the stability diagram is drawn. Moreover, by traversing thermocouple and sampling probe in the flame, the distribution of temperature and NO$_{x}$ mole fraction are measured. With the change in blade angle, flame shape, flame stabilization, the distribution of temperature and NO$_{x}$ mole fraction are changed considerably.rably.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2003년도 유체기계 연구개발 발표회 논문집
• /
• pp.496-501
• /
• 2003

Reynolds averaged Wavier-Stokes simulations based on the Reynolds stress model was performed to investigated the effect of inlet flow angle on the distributions of the Reynolds stress tensor inside tip leakage vortex of a linear compressor cascade. Two different inlet flow angles ${\beta}=29.3^{\circ}$(design condition) and $36.5^{\circ}$(off-design condition) were considered. Stress tensor analysis, which transforms the Reynolds stress into the principal direction, was applied to show an anisotropy of the normal stresses. Whereas the anisotropy was highest in the region where the tip leakage vortex collides the suction side of the blade and tip leakage flow enters between blade tip of the pressure side and the endwall, it had the lowest value at the center of tip leakage vortex. It was also found that the magnitude of maximum shear stress at design condition was greater than that of off-design condition.

• 한국자동차공학회논문집
• /
• 제24권1호
• /
• pp.74-81
• /
• 2016

The aim of this study was to find the initial design value of turbine blade for electrical type turbocompound system generating 10 kW. Turbocompound is one of the waste heat recovery system applying to internal combustion engine to recover exhaust gas energy that was about 30 % of total input energy. To design the turbine blade, 1-D mean line flow model was used. Exhaust gas temperature, pressure, flow rate and turbine rotating speed was fixed as primary boundary conditions. The velocity triangles was defined and used to determine the rotor inlet radius and width, the rotor outlet radius at shroud and radius at hub, the rotor flow angles and the number of blades.

• International Journal of Aeronautical and Space Sciences
• /
• 제14권1호
• /
• pp.30-45
• /
• 2013

The present work focuses on the unsteady aerodynamics and aeroelastic properties of a small-medium sized wind-turbine blade operating under ideal conditions. A tapered/twisted blade representative of commercial blades used in an experiment setup at the National Renewable Energy Laboratory is considered. The aerodynamic loads are computed using Computational Fluid Dynamics (CFD) techniques. For this purpose, FLUENT$^{(R)}$, a commercial finite-volume code that solves the Navier-Stokes and the Reynolds-Averaged Navier-Stokes (RANS) equations, is used. Turbulence effects in the 2D simulations are modeled using the Wilcox k-w model for validation of the CFD approach. For the 3D aerodynamic simulations, in a first approximation, and considering that the intent is to present a methodology and workflow philosophy more than highly accurate turbulent simulations, the unsteady laminar Navier-Stokes equations were used to determine the unsteady loads acting on the blades. Five different blade pitch angles were considered and their aerodynamic performance compared. The structural dynamics of the flexible wind-turbine blade undergoing significant elastic displacements has been described by a nonlinear flap-lag-torsion slender-beam differential model. The aerodynamic quasi-steady forcing terms needed for the aeroelastic governing equations have been predicted through a strip-theory based on a simple 2D model, and the pertinent aerodynamic coefficients and the distribution over the blade span of the induced velocity derived using CFD. The resulting unsteady hub loads are achieved by a first space integration of the aeroelastic equations by applying the Galerkin's approach and by a time integration using a harmonic balance scheme. Comparison among two- and three- dimensional computations for the unsteady aerodynamic load, the flap, lag and torsional deflections, forces and moments are presented in the paper. Results, discussions and pertinent conclusions are outlined.

• 한국항공우주학회지
• /
• 제32권7호
• /
• pp.29-36
• /
• 2004

본 연구에서는 전진비행시 무힌지 로터 블레이드의 허브하중에 대한 복합재료 연성의 영향을 고찰하였다. 무힌지 복합재료 로터 블레이드를 단일 상자형 보로 모델링 하였으며, 전단 변형 및 비틀림 워핑과 같은 비고전적 효과를 고려하였다. 운동방정식은 해밀턴의 원리를 이용하여 구성하였으며, 로터 블레이드의 공간 및 시간차원에서의 유한요소법을 적용하여 완전평형해석을 수행하였다. 블레이드에 작용하는 공기력은 2 차원 준정상 공기력 이론을 바탕으로 하여 역류 및 압축성 효과를 고려하였다. MSC/NASTRAN을 이용하여 피치 -플랩 및 피치-래그와 같은 탄성 연성의 크기를 구하고, 고전적인 기하학적 연계와 비교하였다. 탄생 연성은 $N_b/rev$ 허브하중의 특성에 적지 않은 영향을 미침을 확인하였다 블레이드 복합재료의 적층각을 적절히 변화시킬 경우 약 10-40%의 허브하중을 감소시킬 수 있음을 보였다.

• 한국항공우주학회지
• /
• 제39권8호
• /
• pp.735-743
• /
• 2011

본 연구에서는 직선형 터빈 캐스케이드 장치를 이용하여 분사영역으로 진입하고 퇴각하는 익형의 허브, 평균반경, 팁에 형성되는 표면에서의 압력을 정상상태에서 측정하였다. 익형은 축류형으로 코드가 200mm이며, 분사 노즐은 단면은 사각형으로 그 크기는 $200mm{\times}200mm$이다. 실험은 코드 기준으로 레이놀즈수 $3{\times}10^5$에서 수행되었다. 탈설계 성능을 측정하기 위하여 노즐의 설치각을 $58^{\circ}$, $65^{\circ}$와 $72^{\circ}$로 변경하면서, 노즐의 설치각 변화에 대한 익형에서 표면압 변화의 특성을 파악하였다. 또한 현절비를 1.25, 1.38, 1.67로 변경하면서 현절비 변화에 대한 익형의 표면압 변화를 측정하였다. 실험의 결과에서 익형이 분사영역으로 진입할 때 현절비가 적을수록 흡입면에서는 표면압력의 감소가 발생되었고 낮은 노즐설치각인 경우에는 역회전방향의 힘이 형성되었다. 아울러 양의 입사각으로 익형이 분사영역으로 진입할 때 흡입면의 앞부분에 낮은 압력이 형성되었다.

• 한국융합학회논문지
• /
• 제11권3호
• /
• pp.195-200
• /
• 2020

본 연구에서는 8개의 터빈 날개면들이 각각 추진축상에서 45°, 40°, 35°의 각도로 기울어져 있는 Model 1, 2 및 3인 3가지 Model의 유체클러치 터빈 날개 형상에 대한 유동 해석들을 수행하였다. 터빈 날개면이 추진축상에서 각도가 크게 기울어질수록 터빈 날개의 뒷면 이후에서의 흐름에서 Model들 중에서 가장 유동 압력을 크게 받고 있음을 알 수 있다. 반면에 터빈 날개면이 추진축상에서 각도가 작게 기울어질수록 유동 속도가 작게 된다. 터빈 날개면이 추진축상에서 각도가 작게 기울어질수록, 즉 유체의 흐름과 수직에 가까운 날개 형상이 효율적으로 유체클러치에 동력을 연결하고 차단하는데 있어서 적합함을 알 수 있다. 유체클러치 터빈 날개 유형별 유동해석을 적용함으로서 본 논문에서의 연구 결과는 미적인 설계를 적용할 수 있는 융합 연구자료로서 유리하다고 여겨진다.

• 대한기계학회논문집B
• /
• 제20권12호
• /
• pp.3917-3925
• /
• 1996

A numerical analysis on three dimensional turbulent incompressible flows through linear cascades of turbine rotor blades with high turning angles has been performed by using a generalized k-.epsilon. model which is a high Reynolds number form and derived by RNG(renormalized group) method to account for the variation of the rate of strain. A second order upwind scheme is used to suppress numerical diffusion in approximating the convective terms. Body-fitted coordinates are adopted to represent the complex blade geometry accurately. For the case without tip clearance, velocity vectors and static pressure contours are shown to be in good agreement with previous experimental results. For the case with tip clearance, the effects of the passage vortex and tip clearance flow on the total pressure loss as well as their interactions are discussed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1981-1986
• /
• 2004

A cross-flow fan relatively makes high dynamic pressure at low speed because a working fluid passes through an impeller blade twice and blades have a forward curved shape. Therefore, the performance of a cross-flow fan is influenced 25% by the impeller, 60% by the rearguider and the stabilizer, 15% by the heat exchanger. At the low flow rate, there exists a rapid pressure head reduction, a noise increase and an unsteady flow against a stabilizer and a rearguider. Moreover, it is difficult to analyze the reciprocal relations of the cross-flow fan because each parameter is independent. Numerical analyses are conducted with different starting angles of the rearguider. Two-dimensional, unsteady governing equations are solved, using FVM, PISO algorithm, sliding grid system and ${\kappa}-{\varepsilon}$ standard turbulence model.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2713-2717
• /
• 2008

Whole flow fields of a room air conditioner (RAC) have been visualized by a Particle Image Velocimetry (PIV) technique to analyze the flow structure with various inlet and outlet angles, and to control an eccentric vortex which affects an efficiency and noise of the RAC. A test model with 5 stages of a cross flow fan has been manufactured and a transparent acryl has been installed at the side of the test model for the PIV experiment. The inlet and outlet flows and the flow inside the cross flow fan have been analyzed by varying the inlet grill angles and outlet blade angles. The movement of the eccentric vortex has been investigated experimentally by developing the measurement technique for the inner flow field of the cross flow fan. From the visualization of the inner flows, the origins of the noise inside the RAC and the condensation points around the outlet parts of the cold air have been observed and the solution of the problems can be proposed in this study.