• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.97-100
• /
• 2009

A negative waveform was studied to improve the driving characteristics of reset and address periods in ac PDP. Comparative experiments between negative and conventional positive waveforms were performed with 42-inch XGA PDP module. The negative waveform showed lower breakdown voltage than the conventional positive waveform in reset period. Due to its weak and stable discharge during reset period, the contrast ratio was improved by decreasing the black luminance. During address period, the discharge time-lag was measured. The formative time lag ($=T_f$) of negative waveform was improved about 22.8% than $T_f$ of conventional positive waveform.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.953-956
• /
• 2002

The electro-optical (EO) performances of a multidomain vertical-alignment (MVA) cell on a homeotropic photopolymer have been investigated. In the absence of an electric field, the MVA cell achieved black state as LC alignment is homeotropic. An electric field created by interdigitated electrodes and rib made after photolithograph using the photopolymer on both substrates causes a director deformation of a multidomain type. Good voltage-transmittance curves for a MVA cell on the homeotropic photopolymer were observed. Also, the stable response time of MVA cell on the homeotropic photopolymer can be achieved.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.5
• /
• pp.530-535
• /
• 2004

We have studied 90$^{\circ}$ twisted nematic mode switching by fringe electric field(F-TN mode) using a liquid crystal (LC) with negative dielectric anisotropy. In the device, two polarizers are parallel each other, electrodes exist only on bottom substrate, and one of rubbing direction is coincident with polarizer axis. Therefore, the cell shows a black state before a voltage is applied. With a bias voltage generating fringe-electric field, the LC twists perpendicular to fringe electric field such that the LCs are almost homogeneously aligned except near the bottom surface since the negative type of the LC is used. Consequently, the new device exhibits much wider viewing angle than that of the conventional TN mode due to in-plane switching and relatively high transmittance since the LC director above whole electrode area aligns parallel to the polarizer axis.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.3
• /
• pp.219-223
• /
• 2003

The electro-optical (EO) performances of a multidomain verticial-alignment (MYA) cell on a homeotropic photopolymer have been investigated. In the absence of an electric field, the WVA cell achieved black state as LC alignment is homeotropic An electric field created by interdigitated electrodes and rib made after photolithograph using the photopolymer on both substrates causes a director deformation of a multidomain type. Good voltage transmittance curves for a MVA cell on the homeotropic photopolymer were observed. Also, the stable response time of MYA cell on the homeotropic photopolymer can be achieved.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.2
• /
• pp.169-173
• /
• 2009

We studied driving characteristics according to the ratio of mass and charging (m/q) value for charged toner particles with black and yellow color in charged particle type display panel. After biasing rectangle pulse to the transparency electrodes of putted panel with toner particles, its response time and contrast ratio are simultaneously measured using a laser as a optical source, photodiode as a detector and reflective system. As a results, contrast ratio is largest at the shortest response time region which is different to the particle because of m/q. We proposed relational equation for response time, m/q, cell gap and biasing voltage. It has not been studied and reported to analyze the relationship of response time, biasing voltage, lumping phenomena, cell gap, and contrast ratio for toner particle type display.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.6
• /
• pp.1175-1179
• /
• 2009

We analyze voltage characteristics of charged particle type display according to particle layers and cell gap between two electrodes and ascertain the aging effects by measuring the response time of particles with and without aging process. The threshold/driving/breakdown voltage is proportional to layers of charged particles and cell gap and the response time at driving voltage is faster than that of threshold and breakdown voltage because of different q/m of color and black particles. The analysis of response time is a method of estimation of optical characteristics, driving voltage and particle lumping and these results are promoted by aging process. We use the laser and photodiode to measure response time and optical properties. It has not been studied and reported to analyze the relationship of response time, threshold/driving/breakdown voltage, lumping phenomena, cell gap, and aging process for charged particle type display.

• Journal of radiological science and technology
• /
• v.43 no.2
• /
• pp.79-85
• /
• 2020

The influence of metal artifact in CT image depends on the type of metal materialsm, the reconstruction algorithm, and scan parameters. The presence of metal artifacts was quantitatively evaluated by applying the standard and MAR algorithms through the phantom study. In the change of tube voltage applied the standard algorithm, metal artifact decreased to 44.9% for 80 vs 120 kVp, 24% for 100 vs 120 kVp, while the image taken at 140 kVp increased the artifact by 19% compared to 120 kVp. When the tube current was increased from 100 to 300 mA, there was no significant difference in the CT value and noise. Black band and white strike artifacts occurred up to 65.9% in the adjacent ROI of the metal driver, whereas titanium screw produced lesser metal artifact than that of the metal driver. The combination of 120kVp or higher tube voltage-standard algorithm was effective in removing black band artifacts as well as white streak by high density materials. However, MAR reconstruction algorithm was useful in improving image quality under the environment of low kVp and high density materials, without increase of radiation exposure.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.1
• /
• pp.36-38
• /
• 2013

Eight sample panels using an indium tin oxide(ITO)-coated glass substrate were fabricated, with barrier ribs formed of 55 ${\mu}m$ height and 10 ${\mu}m$ width. The upper and lower substrates were designed with the same panel condition, so a cell gap of 110 ${\mu}m$ was obtained. The charged particles in a cell consisted of $TiO_2$ (for white color) or carbon black (black color), negative or positive charge control agents, and a polymer. The average diameter of the two types of particles was commonly 10 ${\mu}m$, and their q/m value was -4.5 ${\mu}C/g$ and +4.5 ${\mu}C/g$, respectively. The electrically opposite particles mixed by an agitator were loaded into their cells by a simple particle-loading method. The discharging process proceeded at a humidity of 80% and a temperature of $30^{\circ}C$. Reflectivity was measured depending on discharging time, and a hysteresis curve by bias voltage obtained for comparison between the neutralized and non-neutralized panel, in which the superior optical property of the neutralized panel was ascertained.

• Proceedings of the KIEE Conference
• /
• 2008.09a
• /
• pp.207-210
• /
• 2008

In this paper, we researched the dielectric properties and voltage dependence on slice XLPE sheet from 22[kV] and 154[kV] power cable. We studied effects for impurities and water for semiconductor shield through a dielectric properties experiment to estimate performance of insulating materials in power cable. Capacitance and $tan{\delta}$ of 22[kV], 154[kV] were 53/43[pF] and $7.4{\times}10^{-4}$, $2.1510^{-4}$. In these results, the trend was increased with the increase of temperature. The tan6 of XLPE/semiconductor layer was increased as compared with that of XLPE. Dielectric properties reliability of tan6 was small. Also, To improve mean-life and reliability of power cable in this study, we have investigated chemical properties showing by changing the content of carbon black that is semiconductive additives for underground power transmission. Specimens were made of sheet form with the three of existing resins and the nine of specimens for measurement. Chemical properties of specimens was measured by FT-ATR (Fourier Transform Attenuated Total Reflectance). The condition of specimens was a solid sheet. We could observe functional group (C=O, carbonyl group) of specimens through FT-ATR. From these experimental result, the concentration of functional group (C=O) was high according to increasing the content of carbon black. We could know EEA was excellent more than other specimens from above experimental results.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.7
• /
• pp.490-495
• /
• 2018

A multielectrode electronic paper film capable of expressing a single-color image was fabricated by injecting color electronic ink into an electronic paper panel; on the basis of its reflective or transparent properties, it is possible to control the expression of six single-color images and their transmittance. In this study, a single-color image was represented by driving a multielectrode electronic paper film; color coordinates were measured. The six capable single colors were yellowish pink (0.444, 0.354), white (0.355, 0.352), black (0.241, 0.241), orange (0.514, 0.360), reddish orange (0.606, 0.338), and reddish purple (0.469, 0.145). Color particles used in this paper were black and white, by which six colors are accomplished, but more single-color images can be combined by using cyan, magenta, and yellow particles.