• New & Renewable Energy
• /
• v.7 no.2
• /
• pp.10-17
• /
• 2011

Korea is the 11th largest energy consumption country and 96% of its total energy consumption depends on imports from overseas. Therefore it is a very important task to secure renewable energy sources which can reduce both the carbon-dioxide emission and dependency on overseas energy imports. Among the various renewable energy sources, organic wastes are important sources. In Korea, 113 million toe of methane is generated from organic wastes annually, but only 3.7% is effectively used for energy conversion. Thus, it is very important to make better use of organic wastes, especially for power generation. The goals of this project are to develope the fuel supplying system of Bio Gasturbine (GT) for 5MW-class co-generation system. The fuel supplying system mainly consists of $H_2S$ removal system, Bio Gas compression system, Siloxane removal system and moisture separating systems. The fuel requirement of 5MW-class GT is at around 60% of $CH_4$, $H_2S$ (<30 ppm), Siloxane(<10 mg/$nm^3$) and supply pressure (> 25 bar) from biogas compressor. Main mechnical charateristics of Bio Gasturbine system have the specific performance; 1) high speed turbine speed (12,840 rpm) 2) very clean emmission NOx (<50 ppm) 3) high efficiency of energy conversion rate. This paper focuses on the development of design technology for food waste biogas pretreatment system for 5MW-class biogas turbine. The study also has the plan to replace the fuel of gas turbine and other distributed power systems. As the increase of bioenergy, this system help to contribute to spread more New & Renewable Energy and the establishment of Renewable Portfolio Standards (RPS) for Korea.

• Composites Research
• /
• v.26 no.4
• /
• pp.213-217
• /
• 2013

The focus in the present work is to study the agro-waste corn husk bio-filler as reinforcement for polypropylene. These materials have been created by extrusion and injection molding. The effect of filler content by 10, 20, 30 and 40 wt. % and mesh sizes of 50~100, 100 and 300 on the mechanical properties was studied. For the un-notched specimens, the results of flexural strength showed a declining trend with increase the filler loading and the results of impact strength showed an increasing trend with increase the mesh size. In contrast, enhanced flexural modulus was observed with increasing filler loading and size.

• Journal of Microbiology and Biotechnology
• /
• v.33 no.2
• /
• pp.151-166
• /
• 2023

Yeast extract is a product prepared mainly from waste brewer's yeast, which is rich in nucleotides, proteins, amino acids, sugars and a variety of trace elements, and has the advantages of low production cost and abundant supply of raw material. Consequently, yeast extracts are widely used in various fields as animal feed additives, food flavoring agents and additives, cosmetic supplements, and microbial fermentation media; however, their full potential has not yet been realized. To improve understanding of current research knowledge, this review summarizes the ingredients, production technology, and applications of yeast extracts, and discusses the relationship between their properties and applications. Developmental trends and future prospects of yeast extract are also previewed, with the aim of providing a theoretical basis for the development and expansion of future applications.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.26 no.2
• /
• pp.65-73
• /
• 2018

This study was carried out for 20 days in a bio-drying batch reactor under the blowing conditions of 0.75, 1.00, 1.25, and $1.50L/min{\cdot}kg$ in order to optimize the operating conditions for the bio-drying of food wastes. The decomposition rate of organic matter during the bio-drying operation period was analyzed using modified Gompertz model. The maximum organic degradation (P) was 2.31, 2.52, 2.27 and 1.88 kg at air flow rates of 0.75, 1.00, 1.25 and $1.50L/min{\cdot}kg$, and the maximum organic degradation rate was 0.33, 0.45, 0.28, and 0.18 kg/day at 1.00, 1.25 and $1.50L/min{\cdot}kg$, respectively, showing excellent organic decomposition efficiency at a air flow rate of $1.00L/min{\cdot}kg$. The lag growth phase time (${\lambda}$) of the bio-drying reactor was 2.10, 1.48, 1.15, and 1.06 days at 0.75, 1.00, 1.25 and $1.50L/min{\cdot}kg$, respectively. The water removal rate in the operation of bio-drying reactor of food waste increased with the increase of air flow rate from the early stage of bio-drying to the middle stage, and the highest water removal rate was observed at the air flow rate of $1.00L/min{\cdot}kg$ at the end of bio-drying. The optimum air flow rate condition of bio-drying reactor was $1.00L/min{\cdot}kg$.

• Journal of Adhesion and Interface
• /
• v.9 no.2
• /
• pp.16-23
• /
• 2008

In this study, novel waste wool/polypropylene NFRPs (natural fiber reinforced polymer composites), which are constituted with waste wool discarded as industrial scrap during manufacturing processes of woven fabrics and general purpose thermoplastic polypropylene (PP), were fabricated by means of compressionmolding and their mechanical and thermal properties were characterized. The mechanical properties of PP resin were significantly improved by an introduction of waste wool to PP. In particular, as the loading of waste wool was 50 vol% in the NFRP, the flexural strength of the NFRP was increased about 20%, the flexural modulus about 143%, the tensile strength about 76%, and the tensile modulus about 90% in comparison with each of PP control. In addition, the maximum value of the heat deflection temperature (HDT) obtained with the NFRP was $138^{\circ}C$ at a 50 vol% loading of waste wool. This is $21^{\circ}C$ higher than the HDT of PP control. The result here suggests that waste wool be a potential candidate for a reinforcing material of thermoplastic matrix resins.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2006.06a
• /
• pp.44-45
• /
• 2006

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2006.11a
• /
• pp.71-72
• /
• 2006

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.1
• /
• pp.95-103
• /
• 2011

We have investigated pretreatment of waste wood using milling refinery combined with poping method, which can save energy for pretreatment and enzyme loading for enzymatic hydrolysis. The chemical analysis of holocellulose of non and popping treated waste wood showed 65.9% and 58.8%, and the lignin, organic extracts and ash were increased by 3%, 4% and 0.7% after pretreatment, respectively. The reducing sugar yields of pretreated waste wood were increased four times more than non-pretreated one and the synergistic effect of cellulase and xylanase were evaluated compare with individual enzyme treatment. Especially, enzyme cocktail (cellulase 50 U and xylanase 50 U) treatment was very efficient in 1% substrate (50 mg). Also, glucose and xylose conversion rate of pretreated waste wood by GC analysis were 45.9% and 38.7%, respectively.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.10
• /
• pp.667-671
• /
• 2014

By analyzing seed germination indexes of cabbage and radish, this study aims to evaluate the toxicity of food waste compost, which is produced by fermentation-extinction technology with bio wood chips. In the experimental results, the seed germination index of food waste compost for cabbage and radish was shown in the range of a minimum 104 and maximum 170. It was satisfied with the over 70 criteria in the level of the Korea fertilizer process specification. Consequently, the food waste compost from fermentation-extinction reaction with bio wood chips was evaluated by the appropriate compost maturity for the plantation.

• Nuclear Engineering and Technology
• /
• v.55 no.11
• /
• pp.4181-4190
• /
• 2023

Nuclear power plants are subjected to various processes during decommissioning, including cutting, decontamination, disposal, and treatment. The cutting of massive bio-shields is a significant step in the decommissioning process. Cutting is performed near the target structure, and during this process, workers are exposed to potential radioactive elements. However, studies considering worker exposure management during such cutting operations are limited. Furthermore, dismantling a nuclear power plant under certain circumstances may result in the unnecessary radiation exposure of workers and an increase in secondary waste generation. In this study, a cutting scenario was formulated considering the bio-shield as a representative structure. The specifications of a standard South Korean radioactive waste disposal drum were used as the basic conditions. Additionally, we explored the hot-to-cold and cold-to-hot methods, with and without the application of polishing during decontamination. For evaluating various scenarios, different cutting time points up to 30 years after permanent shutdown were considered, and cutting speeds of 1-10nullm²/h were applied to account for the variability and uncertainty attributable to the design output and specifications. The obtained results provide fundamental guidelines for establishing cutting methods suitable for large structures.