• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1507-1510
• /
• 2005

This study was carried out as a part of the research on the development of a maskless and electroless process for fabricating metal micro/nanostructures by using a nanoindenter and an electroless deposition technique. $2-\mu{m}-deep$ indentation tests on Ni and Cu samples were performed. The elastic recovery of the Ni and Cu was 9.30% and 9.53% of the maximum penetration depth, respectively. The hardness and the elastic modulus were 1.56 GPa and 120 GPa for Ni and 1.49 GPa and 100 GPa for Cu. The effect of single-point diamond machining conditions such as the Berkovich tip orientation (0, 45, and $90^{\circ}$) and the normal load (0.1, 0.3, 0.5, 1, 3, and 5 mN), on both the deformation behavior and the morphology of cutting traces (such as width and depth) was investigated by constant-load scratch tests. The tip orientation had a significant influence on the coefficient of friction, which varied from 0.52-0.66 for Ni and from 0.46-0.61 for Cu. The crisscross-pattern sample showed that the tip orientation strongly affects the surface quality of the machined area during scratching. A selective deposition of Cu at the pit-like defect on a p-type Si(111) surface was also investigated. Preferential deposition of the Cu occurred at the surface defect sites of silicon wafers, indicating that those defect sites act as active sites for the deposition reaction. The shape of the Cu-deposited area was almost the same as that of the residual stress field.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.8 s.185
• /
• pp.171-177
• /
• 2006

This study was performed as a part of the research on the development of a maskless and electroless process for fabricating metal micro/nanostructures by using a nanoindenter and an electroless deposition technique. $2-{\mu}m$-deep indentation tests on Ni and Cu samples were performed. The elastic recovery of the Ni and Cu was 9.30% and 9.53% of the maximum penetration depth, respectively. The hardness and the elastic modulus were 1.56 GPa and 120 GPa for Ni and 1.51 GPa and 104 GPa for Cu. The effect of single-point diamond machining conditions such as the Berkovich tip orientation (0, 45, and $90^{\circ}$ ) and the normal load (0.1, 0.3, 0.5, 1, 3, and 5 mN), on both the deformation behavior and the morphology of cutting traces (such as width and depth) was investigated by constant-load scratch tests. The tip orientation had a significant influence on the coefficient of friction, which varied from 0.52-0.66 for Ni and from 0.46- 0.61 for Cu. The crisscross-pattern sample showed that the tip orientation strongly affects the surface quality of the machined are a during scratching. A selective deposition of Cu at the pit-like defect on a p-type Si(111) surface was also investigated. Preferential deposition of the Cu occurred at the surface defect sites of silicon wafers, indicating that those defect sites act as active sites for the deposition reaction. The shape of the Cu-deposited area was almost the same as that of the residual stress field.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2000.11a
• /
• pp.3-4
• /
• 2000

Many researchers are interested in the synthesis and characterization of carbon nitride and diamond-like carbon (DLq because they show excellent mechanical properties such as low friction and high wear resistance and excellent electrical properties such as controllable electical resistivity and good field electron emission. We have deposited amorphous carbon nitride (a-C:N) thin films and DLC thin films by shielded arc ion plating (SAIP) and evaluated the structural and tribological properties. The application of appropriate negative bias on substrates is effective to increase the film hardness and wear resistance. This paper reports on the deposition and tribological OLC films in relation to the substrate bias voltage (Vs). films are compared with those of the OLC films. A high purity sintered graphite target was mounted on a cathode as a carbon source. Nitrogen or argon was introduced into a deposition chamber through each mass flow controller. After the initiation of an arc plasma at 60 A and 1 Pa, the target surface was heated and evaporated by the plasma. Carbon atoms and clusters evaporated from the target were ionized partially and reacted with activated nitrogen species, and a carbon nitride film was deposited onto a Si (100) substrate when we used nitrogen as a reactant gas. The surface of the growing film also reacted with activated nitrogen species. Carbon macropartic1es (0.1 -100 maicro-m) evaporated from the target at the same time were not ionized and did not react fully with nitrogen species. These macroparticles interfered with the formation of the carbon nitride film. Therefore we set a shielding plate made of stainless steel between the target and the substrate to trap the macropartic1es. This shielding method is very effective to prepare smooth a-CN films. We, therefore, call this method "shielded arc ion plating (SAIP)". For the deposition of DLC films we used argon instead of nitrogen. Films of about 150 nm in thickness were deposited onto Si substrates. Their structures, chemical compositions and chemical bonding states were analyzed by using X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy and infrared spectroscopy. Hardness of the films was measured with a nanointender interfaced with an atomic force microscope (AFM). A Berkovich-type diamond tip whose radius was less than 100 nm was used for the measurement. A force-displacement curve of each film was measured at a peak load force of 250 maicro-N. Load, hold and unload times for each indentation were 2.5, 0 and 2.5 s, respectively. Hardness of each film was determined from five force-displacement curves. Wear resistance of the films was analyzed as follows. First, each film surface was scanned with the diamond tip at a constant load force of 20 maicro-N. The tip scanning was repeated 30 times in a 1 urn-square region with 512 lines at a scanning rate of 2 um/ s. After this tip-scanning, the film surface was observed in the AFM mode at a constant force of 5 maicro-N with the same Berkovich-type tip. The hardness of a-CN films was less dependent on Vs. The hardness of the film deposited at Vs=O V in a nitrogen plasma was about 10 GPa and almost similar to that of Si. It slightly increased to 12 - 15 GPa when a bias voltage of -100 - -500 V was applied to the substrate with showing its maximum at Vs=-300 V. The film deposited at Vs=O V was least wear resistant which was consistent with its lowest hardness. The biased films became more wear resistant. Particularly the film deposited at Vs=-300 V showed remarkable wear resistance. Its wear depth was too shallow to be measured with AFM. On the other hand, the DLC film, deposited at Vs=-l00 V in an argon plasma, whose hardness was 35 GPa was obviously worn under the same wear test conditions. The a-C:N films show higher wear resistance than DLC films and are useful for wear resistant coatings on various mechanical and electronic parts.nic parts.

• Transactions of Materials Processing
• /
• v.13 no.4
• /
• pp.326-333
• /
• 2004

The nanoprobe based on lithography, mainly represented by SPM based technologies, has been recognized as a potential application to fabricate the surface nanosctructures because of its operational versatility and simplicity. However, nanoprobe based on lithography itself is not suitable for mass production because it is time a consuming method and not economical for commercial applications. One solution is to fabricate a mold that will be used for mass production processes such as nanoimprint, PDMS casting, and others. The objective of this study is to fabricate the silicon stamper for PDMS casting process by a mastless fabrication technique using the combination of nano/micro machining by Nanoindenter XP and KOH wet etching. Effect of the Berkovich tip alignment on the deformation was investigated. Grooves were machined on a silicon surface, which has native oxide on it, by constant load scratch (CLS), and they were etched in KOH solutions to investigate chemical characteristics of the machined silicon surface. After the etching process, the convex structures was made because of the etch mask effect of the mechanically affected layer generated by nanoscratch. On the basis of this fact, some line patterns with convex structures were fabricated. Achieved groove and convex structures were used as a stamper for PDMS casting process.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.771-774
• /
• 2003

The mechanical properties of barrier ribs in PDP require quantification in order to control the defects and to increase the yield in the process. Several different types of rib materials were tested for hardness (H) and Young's modulus (E) with a microtip indenter (Berkovich type). For the assessment of fracture toughness of the rib, a macro Vikers indenter was used. The materials with 30wt% of filler were fired at between $490^{\circ}C$ and $570^{\circ}C$. As a result, the composite became fully densified at $520^{\circ}C$, which is near the T s (Littleton softening point) of glass frit. As the filler content increased, the fracture toughness also $(K_{IC})$ increased in the range of 0.60 to 2.63 $MPa{\cdot}m^{0.5}$ after sintering at $550^{\circ}C$. The results suggest that the application of a nano-indenter would be useful for testing the mechanical properties of barrier ribs.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.172-172
• /
• 2011

현대 반도체 금속배선 연구에서는 기존에 쓰이던 Al (Aluminium) 금속배선 대신에 Cu(Copper) 금속배선 연구가 진행 되고 있다. Cu는 Al 보다 비저항이 낮고, 녹는점도 Al보다 높다는 장점이 있지만 저온에서 기판인 Si (Silicon) 과 반응하고 접착력이 우수하지 못 하다는 단점이 있다. 이런 문제를 해결하기 위하여 확산방지막을 기판과 금속배선 사이에 삽입하는 방법이 제시 되었다. 확산방지막으로는 기존에 쓰이던 Ti (Titanium) 계열의 확산방지막과 W (Tungsten) 계열의 확산방지막이 있다. 이번 연구에서는 W 계열의 확산방지막에 불순물 C (Carbon), N(Nitrogen)을 첨가한 W-C-N 확산방지막 시편을 제조하였고, N2의 비율을 변화시키며 $600^{\circ}C$ 열처리를 하였다. 실험 결과 질소의 포함 농도에 따라 확산방지막의 안정도가 변화한다는 결과를 얻었으며, 질소 첨가량에 따라 시편의 표면 보다는 시편의 중간층의 물성 변화율이 큰데 이는 시편 표면의 질소는 열처리 중 확산에 의한 시편과의 분리 현상이 일어나지만 시편의 중간층은 trap현상에 의하여 시편에 남아있어 질소의 영향을 받아 시편의 중간층이 더욱 질소 유량에 따른 영향이 큰 것을 확인하였다. 이 결과로부터 W-C-N 박막은 첨가된 질소의 유량에 따라 박막의 안정도가 결정된 다는 것을 알았다. 본 연구에서 시편은 rf magnetron sputtering 방법으로 제작하였고 연속압입 실험은 Hysitron사의 Triboindenter를 이용하였다. Indenting에 사용된 압입팁은 Berkovich tip을 사용하였다.

• Transactions of Materials Processing
• /
• v.12 no.7
• /
• pp.640-646
• /
• 2003

The nanoprobe based on lithography, mainly represented by SPM based technologies, has been recognized as potential application to fabricate the surface nanostructures because of its operational versatility and simplicity. The objective of the work is to suggest new mastless pattern fabrication technique using the combination of machining by nanoindenter and KOH wet etching. The scratch option of the nanoindenter is a very promising method for obtaining nanometer scale features on a large size specimen because it has a very wide working area and load range. Sample line patterns were machined on a silicon surface, which has a native oxide on it, by constant load scratch (CLS) of the Nanoindenter with a Berkovich diamond tip, and they were etched in KOH solutions to investigate chemical characteristics of the machined silicon surface. After the etching process, the convex structure was made because of masking effect of the affected layer generated by nano-scratch. On the basis of this fact, some line patterns with convex structures were fabricated. Achieved patterns can be used as a mold that will be used for mass production processes such as nanoimprint or PDMS molding process. All morphological data of scratch traces were scanned using atomic force microscope (AFM).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.181-181
• /
• 2010

현대 반도체 금속배선 연구에서는 기존에 쓰이던 Al (Aluminium) 금속배선 대신에 Cu (Copper) 금속배선 연구가 진행되고 있다. Cu는 Al 보다 비저항이 낮고, 녹는점도 Al보다 높다는 장점이 있지만 저온에서 기판인 Si (Silicon) 과 반응하고 접착력이 우수하지 못 하다는 단점이 있다. 이런 문제를 해결하기 위하여 확산방지막을 기판과 금속배선 사이에 삽입하는 방법이 제시 되었다. 확산방지막으로는 기존에 쓰이던 Ti (Titanium) 계열의 확산방지막과 W (Tungsten) 계열의 확산방지막이 있다. 이번 연구에서는 W 계열의 확산방지막에 불순물 C (Carbon) 과 N (Nitrogen) 을 첨가한 W-C-N 확산방지막 시편을 제조하였고, N2의 비율을 변화시키며 $600^{\circ}C$, $800^{\circ}C$열처리를 하였다. 본 실험의 결과로, 확산방지막의 $N_2$ 농도가 0, 0.5, 2 sccm으로 증가할수록 고온에서도 Elastic modulus 와 Hardness 값이 시편의 여러 영역에서 비교적 안정적으로 유지된다는 결과를 얻었다. 이 결과로부터 W-C-N 박막의 질소 농도에 따라 고온에서도 비교적 안정적으로 유지된다는 결과를 얻었다. 본 연구에서 시편은 RF magnetron sputtering 방법으로 제작하였고 Elastic modulus와 Hardness의 측정은 Hysitron사의 Triboindenter를 이용하였다. Indenting에 사용된 압입팁은 Berkovich tip을 사용하였다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.9
• /
• pp.859-869
• /
• 2009

The sharp indenters such as Berkovich and conical indenters have a geometrical self-similarity in theory, but different materials have the same load-depth curve in case of single indentation. In this study, we analyze the load-depth curves of conical indenter with angles of indenter via finite element method. From FE analyses of dual-conical indentation test, we investigate the relationships between indentation parameters and load-deflection curves. With numerical regressions of obtained data, we finally propose indentation formulae for material properties evaluation. The proposed approach provides stress-strain curve and the values of elastic modulus, yield strength and strain-hardening exponent with an average error of less than 2%. It is also discussed that the method is valid for any elastically deforming indenters made of tungsten carbide and diamond for instance. The proposed indentation approach provides a substantial enhancement in accuracy compared with the prior methods.