• Journal of the Korean Society of Marine Environment & Safety
• /
• v.21 no.6
• /
• pp.778-783
• /
• 2015

We studied about the strength characteristics of the FRP bonding method due to reduce accident on the oceans and protect life for my people. We test tension and bending strength of butt joint, lap joint, V-scarf joint, X-scarf joint. The result of test, it's pattern is similar both tension and bending strength. Tension strength and bending strength was excellent in order to X-scarf-butt joint-V-scarf-lap joint. The tension strength is the best properties X-scarf showed a 57% strength rate of the basic material, and bending strength showed a 77% strength rate of the basic material. Overall, the X-scarf 12t joint has most excellent properties of tension and bending strength. The lap joint has worst properties of tension and bending strength. We have to test having different over-lay of V-scarf and X-scarf joint each 12t, 16t, 20t. V-scarf of 20t over-lay has excellent character of tension and bending strength. But X-scarf of 12t over-lay has excellent character of tension and bending strength. The results are shown to the contrary. The ship is received a lot of stress. it's hard to compare a direction both actual and test. But we can acknowledge material basic characteristic of strength through tension and bending test. We give the four repair method; butt joint, lap joint, V-scarf joint, X-scarf joint and the reduced ratio in comparison with basic material; In addition give the separated data for V-scarf and X-scarf characteristic of 12t, 16t, 20t overlay length. For our study repair man can select good repair method in his work station.

• Journal of the Korean Wood Science and Technology
• /
• v.12 no.3
• /
• pp.15-24
• /
• 1984

The $3{\times}3{\times}30\;cm^3$ sized specimens of Douglas-fir(Pseudotsuga menziesii) and western hemlock(Tsuga heterophylla) in this study were soaked in four fire-retardant solutions of ammonium sulfate, monoammonium phosphate, diammonium phosphate, and aluminium chloride for 1, 24, 72, 168, and 336 hours. Subsequently they were air-dried and burned at high temperature of ca. $1,800^{\circ}C$ and for short time of 5 minutes. This study estimated the relationship between the adsorbed chemicals and the residual weight ratio or residual bending strength of these partly burned lumbers. The results were as follows; 1) In average amount of chemical adsorption, diammonium phosphate showed the largest and aluminium chloride the smallest regardless of species but monoammonium phosphate was larger in Douglas-fir than that of western hemlock. 2) The amount of chemical adsorption was larger in western hemlock than Douglas-fir on the whole. 3) The amount of chemical adsorption was increased with the increase of soaking time but the rate of increase began to decrease at 200hrs. 4) Residual weight ratios showed no difference between species but showed differences among the chemicals treated i.e. monoammonium phosphate, diammonium phosphate, ammonium sulfate and aluminium chloride in turn from the largest to the smallest. 5) MOR values showed linear increase with the increase of residual weight ratios but showed no difference in species and chemicals respectively. 6) In the relationship between amount of chemical adsorption and MOR, only diammonium phosphate showed the curve of secondary degree with significance in Douglas-fir. 7) The MOE value of burned Douglas-fir lumber increased and showed significance of 99% as the adsorbed chemical amount increased, but among the chemicals only monoammonium phosphate showed significance. The MOE value of burned western hemlock lumber didn't show significance. 8) In only Douglas-fir, the correlation between adsorbed chemical amount and work to proportional limit showed significance in only monoammonium phosphate. And in both Douglas-fir and western hemlock, the correlation between adsorbed chemicals and work to maximum load showed significance in monoammonium phosphate.

• Asian Spine Journal
• /
• v.12 no.6
• /
• pp.1106-1116
• /
• 2018

Study Design: Prospective observational study. Purpose: To evaluate the disability domains relevant to Indian patients with low backache and propose a modified disability questionnaire for such patients. Overview of Literature: The Oswestry Disability Index (ODI) is a self-reported measurement tool that measures both pain and functional status and is used for evaluating disability caused by lower backache. Although ODI remains a good tool for disability assessment, from the Indian perspective questions related to weight lifting and sexual activity of ODI are questioned in some of the earlier studies. Activities of daily living in Indian patients vary substantially from those in other populations and include activities like bending forwards, sitting in floor and squatting which are not represented in the ODI. Methods: In this prospective observational study, a seven-step approach was used for the development of a questionnaire. Thirty patients were interviewed to identify the most challenging issue they faced while performing their daily activities (by free listing) and understand how important the questionnaire items were in terms of the standard ODI. Thus, a comprehensive disability questionnaire comprising 14 questions was developed and administered to 88 patients. Both qualitative (interviews) and quantitative methods (to establish the validity, reliability, and correlation with the Visual Analog Scale [VAS] and Rolland Morris disability questionnaire) were used to identify the 10 questions that best addressed the disability domains relevant to Indian patients. Results: According to free listing, four new questions pertaining to bending forward, sitting on the floor, walking on uneven surfaces, and work-related disabilities were included. In the second phase, wherein the questionnaire with 14 items was used, 56.8% patients did not answer the questions related to sexual activity, whereas 23.8% did not answer those related to walking on uneven surfaces. The modified questionnaire demonstrated good internal consistency (Cronbach's alpha=0.892) and correlation with the Rolland Morris questionnaire (Cronbach's alpha=0.850, p>0.05), as well as with the VAS score for disability (Cronbach's alpha=0.712, p>0.05) and pain (Cronbach's alpha=0.625, p>0.05). Conclusions: A modified disability questionnaire that was designed by adding two questions related to bending forward and work status and removing questions related to sexual activity and weight lifting or traveling (depending on the occupation) can help evaluate disability caused by back pain in Indian population.

• Polymer(Korea)
• /
• v.25 no.3
• /
• pp.435-440
• /
• 2001

The objective of this study was to examine the effect of oxidation inhibitor contents on the work of adhesion, fracture toughness, and impact strength of the unidirectional carbon-carbon composites (C/C composites). The molybdenum disilicide ($MoSi_2$) used as an oxidation inhibitor was impregnated with phenolic resins to improve the anti-oxidation properties of the composites in different concentrations of 4, 12 and 20 wt%. Based on Wilhelmy equation, the work of adhesion of C/C composites was calculated by contact angle methods. Fracture toughness and impact strength were pressured by three-point bending test for the critical intensity factor ($K_IC$) and Izod test method, respectively. As a result, the composites made with $MoSi_2$ resulted in an increasing of both fracture toughness and impact strength. Especially, the composites made with 12 wt% $MoSi_2$ content showed the highest value of London dispersive component, $W_A\;^L$, in work of adhesion, resulting from improving the interfacial adhesion force among fibers, filler, and matrix in this system.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.446-446
• /
• 2011

One dimensional (1-D) structures of ZnO nanorods are promising elements for future optoelectronic devices. However there are still many obstacles in fabricating high-quality p-type ZnO up to now. In addition, it is limited to measure the degree of the doping concentration and carrier transport of the doped 1-D ZnO with conventional methods such as Hall measurement. Here we demonstrate the measurement of the electronic properties of p- and n-doped ZnO nanorods by the Kelvin probe force microscopy (KPFM). Vertically aligned ZnO nanorods with intrinsic n-doped, As-doped p-type, and p-n junction were grown by vapor phase epitaxy (VPE). Individual nanowires were then transferred onto Au films deposited on Si substrates. The morphology and surface potentials were measured simultaneously by the KPFM. The work function of the individual nanorods was estimated by comparing with that of gold film as a reference, and the doping concentration of each ZnO nanorods was deduced. Our KPFM results show that the average work function difference between the p-type and n-type regions of p-n junction ZnO nanorod is about ~85meV. This value is in good agreement with the difference in the work function between As-doped p- and n-type ZnO nanorods (96meV) measured with the same conditions. This value is smaller than the expected values estimated from the energy band diagram. However it is explained in terms of surface state and surface band bending.

• Journal of the Ergonomics Society of Korea
• /
• v.35 no.2
• /
• pp.67-74
• /
• 2016

Objective: The aim of this study is to develop a farming shovel to reduce workload, which helps farmers lower the risk of musculoskeletal disease. Background: Most of work using farming tools including shovels requires repetitive works and awkward postures on body parts, and it could possibly cause work-related musculoskeletal disorders. It is necessary to develop and distribute farm equipment and tools in order to reduce physical workload. Method: To improve the most uncomfortable task perceived by ten farmers during the work with a shovel, the improved shovel was designed and made as a prototype for experiment for the comparison of the existing and improved shovels. Twenty males were recruited for this experiment, and muscle activity (%MVC) of six body parts and subjective discomfort ratings by body parts while working with a shovel were measured. A paired t-test was performed to compare physical workload between the existing shovel and the developed one. Results: A shovel applying foothold tied between shaft and blade was designed, which can help workers reduce repetitive bending of back and pressures for upper limbs while digging soil. According to compared evaluation of the developed shovel and the existing shovel, the developed shovel's %MVCs in all experimental muscles were significantly lower than those of the existing shovel. The developed shovel showed the biggest drop in perceived subjective discomfort rating of back, followed by arm and neck, compared to the existing shovel. Conclusion: It was confirmed that attaching a foothold to a shovel was an effective way of reducing workload in back and upper limbs during digging. Application: In the near future, if we put the prototype of developed shovel to practical use after making up for defects, it will help farm work environment be healthier and safer.

• Journal of the Korean Wood Science and Technology
• /
• v.12 no.2
• /
• pp.20-26
• /
• 1984

This study was carried out to investigate the influence of chemical type and its retention in the fire-retardant treated plywoods on the static bending strength, a property peculiar to plywood. Being soaked in 20% aqueous solution of $(NH_4)_2SO_4$, $NH_4H_2PO_4$, $(NH_4)_2HPO_4$. Borax-Boric acid and Minalith for 3 to 12 hours at three-hour intervals and redried at $120^{\circ}C$ in hot press, the treated plywoods were put to static bending test. The values of chemical treated plywoods in Stress at proportional limit, Modulus of elasticity, Modulus of rupture and Work per unit volume to proportional limit were widely higher than those of water treated plywoods(control) and Borax-Boric acid treatment showed the highest value in the four mechanical data. And the bending strength of fire-retardant treated plywoods increased with the extension of soaking time or the increase of chemical retention in themselves. Borix-Boric acid was the desirable fire-retardant for thin plywood in view of mechanical strength and soaking defects in this study.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.3
• /
• pp.49-55
• /
• 2017

Most motor cases adopt deep drawing products, which are excellent in waterproof functions, concentricity, right angle, and quality. In addition, the blower motor and seat motor, which are installed in the car interior and do not require waterproof function, adopts a multi-forming manufacturing method. The deep drawing process requires an expensive transfer press that can digest approximately 12 processes, such as drawing, trimming and piercing. On the other hand, products can be produced with low investment because the multi-forming method is composed of one multi-forming machine or one multi-forming machine and one press. The multi-forming machine is a high-priced facility that is mostly imported and a bending / shearing process multi-foaming machine, which was developed by domestic small and medium-sized enterprises, is not enough to reduce the production cost. An integral multi - forming machine is used as a limited working method for thin material and small products. A large product and thick material has a high shear load. A large product and thick material has a high shear load and uses a single crank press. After blanking, the worker manually feeds the material to a multi-forming machine. When the bending operation is performed in the multi-forming machine, it is transferred to the press again to calibrate the dimensions. This variance in work processes has resulted in lower cost competitiveness due to the lower productivity, quality issues, and excessive operator input. The aim of this study was to establish a stable and cost - effective production system through bending / shearing process separation and facility automation.

• Smart Structures and Systems
• /
• v.25 no.2
• /
• pp.197-218
• /
• 2020

In this work, thermomechanical flexural analysis of functionally graded material sandwich plates with P-FGM face sheets and E-FGM and symmetric S-FGM core is performed by employing a nth-order shear deformation theory. A novel type of S-FGM sandwich plates, namely, both P-FGM face sheets and a symmetric S-FGM hard core are considered. By employing only four unknown variables, the governing equations are obtained based on the principle of virtual work and then Navier method is used to solve these equations. Analytical solutions are deduced to compute the stresses and deflections of simply supported S-FGM sandwich plates. The effects of volume fraction variation, geometrical parameters and thermal load on thermomechanical flexural behavior of the symmetric FGM sandwich plates are investigated.

• Steel and Composite Structures
• /
• v.21 no.5
• /
• pp.963-980
• /
• 2016

The jib system with middle strut is widely used to achieve the large arm length in the large scale tower crane and the deployability in the mobile construction crane. In this paper, an analytical solution for the out-of-plane buckling of the jib system with middle strut is proposed. To obtain the analytical expression of the buckling characteristic equation, the method of differential equation was adopted by establishing the bending and torsional differential equation of the jib system under the instability critical state. Compared with the numerical solutions of the finite element software ANSYS, the analytical results in this work agree well with them. Therefore, the correctness of the results in this work can be confirmed. Then the influences of the lateral stiffness of the cable fixed joint, the dip angle of the strut, the inertia moment of the strut, and the horizontal position of the cable fixed joint on the out-of-plane buckling behavior of the jib system were investigated.