• Smart Structures and Systems
• /
• v.31 no.3
• /
• pp.301-309
• /
• 2023

Tilt is a key indicator of structural safety. Real-time monitoring of tilt responses helps to evaluate structural condition, enable cost-effective maintenance, and enhance lifetime resilience. This paper presents a prototype wireless sensing system for structural tilt measurement. Long range (LoRa) technology is adopted by the sensing system to offer long-range wireless communication with low power consumption. The sensor integrates a gyroscope and an accelerometer as the sensing module. Although tilt can be estimated from the gyroscope or the accelerometer measurements, these estimates suffer from either drift issue or high noise. To address this challenging issue and obtain more reliable tilt results, two sensor fusion algorithms, the complementary filter and the Kalman filter, are investigated to fully exploit the advantages of both gyroscope and accelerometer measurements. Numerical simulation is carried out to validate and compare the sensor fusion algorithms. Laboratory experiment is conducted on a simply supported beam under moving vehicle load to further investigate the performance of the proposed wireless tilt sensing system.

• Korean Journal of Food Science and Technology
• /
• v.26 no.6
• /
• pp.704-708
• /
• 1994

This study was performed to compare quality of citron juice as affected by the extraction method. The yield of citron juice was 24.49% by method I (rotary-crushing and screening), 18.09% by method II (pressing) and 12.60% by method III (belt-pressing), respectively. Juices by methods I and II had more soluble solid contents and essential oil and pulp volume than that by method III. Method III was higher in titratable acidity than methods I and II. The contents of fructose, glucose and sucrose in method III were 0.54%, 0.37% and 1.11%, respectively, which were lower values than those in other methods. But there was no siginificant difference in the contents of total sugar by the extraction method. For fatty acids composition, the contents of oleic acid in method I, palmitic acid, linoleic acid and linolenic acid in method II, and stearic acid in method III, respectively, were highest when compared with other methods. The contents of free amino acids detected in method III were smaller than those in methods I and II. Threonin was detected only in method I, methionine and cystine were not detected in methods I. II and III. But the contents of the total amino acids in method III were $1.3{\sim}1.6$ times as large as those in methods I and II.

• Applied Biological Chemistry
• /
• v.41 no.2
• /
• pp.181-186
• /
• 1998

The effects of sewage treatment on characteristics of sludge as a composting material were investigated for a year during the initial operation at the full-scale Chunan sewage treatment plant. Due to the shortage of design capacity of belt press, a sludge dewatering unit, non-volatile solids were recirculating and concentrating in the treatment plant, resulting in an increase of MLSS and a decrease in F/M ratio at the activated sludge system. Special attention is required for long term operations since the increase of non-volatile solids in the plant would deteriorates the treatment efficiency. The sewage sludge of the Chunan sewage treatment plant showed 79.5% of water content, 11.6% of organic content, and C/N ratio of 6.1, and contained As 1.8 mg/kg, Cd 27 mg/kg, Hg <0.1 mg/kg, Pb 54 mg/kg, T-Cr 370 mg/kg, and Cu 1,100mg/kg of heavy metals. In order to be used as raw material for optimum composting, the sewage sludge requires bulking agents for moistrure/porosity control and a carbon source for adjusting C/N ratio. However, the sewage sludge is not adequate as a soil conditioner after composing due to a high content of heavy metals. If the sewage sludge has to he used as a soil conditioner after composting, it as required to identify and remove tire industrial wastewater portions in tire influent of the plant since heavy metals in the influent were mostly concentrated in dewatered sludge.

• Journal of Environmental Science International
• /
• v.13 no.7
• /
• pp.681-687
• /
• 2004

This study was focused on the manufacturing method of a dewatering aid, which would reduce the water content of the sludge cake by enhancing the dewaterability of sewage sludge. The pretreatment technology for sludge by using radiation and among diverse discarded resources were starfish selected as the material to manufacture the dewatering aid. Starfish went through the process of washing, drying, and pulverizing. The starfish powder made in this process was applied to the digested sludge generated at the sewage treatment plant of D City, and its effects were investigated. The starfish powder that was 300 ${\mu}m$ in particle size was added to the irradiated digested sludge. After the application of the condensation process, the sludge with the starfish powder added was dewatered using the belt press and centrifuge, which were the traditional pressure dewatering devices. As the result, it reduced the water content of the sludge 20% higher than the dewatered cake with no dewatering aid added and irradiation. When the powder was added, it contributed to less use of the coagulant added. The more irradiation dose, the lower water content did the dewatered cake have and the more coagulant was needed for condensation, which seems to be a disadvantage that can be compensated for by the starfish dewatering aid. A small-scaled treatment of the study to a radiation technology and dewatering aid using a discarded resource confirmed the potential of dewaterability. Based on the results saying that the dewatering aid and radiation technology can improve dewatering effects using the traditional dewatering devices, this pretreatment technology will be expected to be applied to sewage treatment plants.

• Resources Recycling
• /
• v.13 no.3
• /
• pp.12-18
• /
• 2004

A study on the enhancement of the dewaterability of sewage sludge was carried out by using the sea waste materials as a dewatering aid. It was made from a starfish and a shell by heating at $105∼700 ^{\circ}C$ and centrifuge and belt press were used as a mechanical dewatering process. The moisture content of sludge cake was reduced by 15∼22% (w/w) after addition of the dewatering aid at the dose of 1∼8 g/100mL of digested sludge. CST (capillary suction time) was measured to evaluate the effect of dewatering aid on sludge dewatering properties. CST was reduced after addition of a shell while increased after addition of a starfish. Enhancement of dewaterability after addition of a shell was better than that of a starfish. The heating temperature effect of the dewatering aid on dewaterability was not clear.

• Earthquakes and Structures
• /
• v.9 no.4
• /
• pp.875-891
• /
• 2015

Earthquake can occur anywhere in the world and it is essential to design important members in special structures based on maximum possible forces that can be produced in them under severe earthquake. In addition, since the earthquake is an accidental phenomena and there are no similar earthquakes, therefore the possibility of strong earthquakes should be taken into account in earthquake-resistant design of important structures. Based on this viewpoint, finding the critical acceleration which maximizes internal forces is an essential factor in structural design. This paper proposes critical excitation method to compute the critical acceleration in design of important members in special structures. These critical accelerations are computed so that the columns' internal shear force at the base of the structure at each time step is maximized under constraints on ground motion. Among computed critical accelerations (of each time step), the one which produces maximum internal shear force is selected. A numerical example presents to show the efficiency of critical excitation method in determining the maximum internal shear force and base moment under variety of constraints. The results show that these method can be used to compute the resonant earthquake which have large enough effective duration of earthquake strong motion (between 12.86 sec to 13.38 sec) and produce the internal shear force and base moment for specific column greater than the same value for selected earthquakes in constructing the critical excitation (for different cases about 2.78 to 1.29 times the San Fernando earthquake). Therefore, a group of them can be utilized in developing the response spectrum for design of special structures.

• Smart Structures and Systems
• /
• v.14 no.1
• /
• pp.39-54
• /
• 2014

Node layout optimization of structural wireless systems is investigated as a means to prolong the network lifetime without, if possible, compromising information quality of the measurement data. The trade-off between these antagonistic objectives is studied within a multi-objective layout optimization framework. A Genetic Algorithm is adopted to obtain a set of Pareto-optimal solutions from which the end user can select the final layout. The information quality of the measurement data collected from a heterogeneous WSN is quantified from the placement quality indicators of strain and acceleration sensors. The network lifetime or equivalently the network energy consumption is estimated through WSN simulation that provides realistic results by capturing the dynamics of the wireless communication protocols. A layout optimization study of a monitoring system on the Great Belt Bridge is conducted to evaluate the proposed approach. The placement quality of strain gauges and accelerometers is obtained as a ratio of the Modal Clarity Index and Mode Shape Expansion values that are computed from a Finite Element model of the monitored bridge. To estimate the energy consumption of the WSN platform in a realistic scenario, we use a discrete-event simulator with stochastic communication models. Finally, we compare the optimization results with those obtained in a previous work where the network energy consumption is obtained via deterministic communication models.

• Journal of the Korean Society of School Health
• /
• v.10 no.2
• /
• pp.193-211
• /
• 1997

The study was designed to gain necessary basic data in order to grasp the health knowledge, attitude, and practice level of students and teachers of elementary, middle and high schools. This study was conducted through interviews of 3,400 students and 1,022 teachers attending 14 different schools large, middle and small cities and rural towns during a period of nine months (from Oct. 2 1995 to Jun. 30 1996). By the results of this study, the recommendations can be summarized as follows: 1. A school health development committee should be established of 10 members: school health related teachers (physical trainers, nurses, and teachers in charge of health), parents, persons related to health administration, local medical doctors, and student reprensentatives in order to support and immplement school health development plans. 2. Like advanced countries, a health class of 2~4 hours should beplaced in middle and high schools. A nurse majoring in health from a university should be the teacher. 3. A curriculum of health should contain the following: education on health, sex, alcohol, tabacco, the misuse of the drugs, the structure and function of human body, the growth of the body, mental health, safety and emergency care, the prevention of disease, proper eating habits and nutrition, daily health life, family health education, society health, community health, environmental pollution and individual responsibility. 4. Create a school health promotion center, with a nurse's office, and a sports center which has health machines (bars, aerobics, training, twist machine, belt massage, running machine, bench press, chest waist, hack hip extension machine) as well as a physical strength measuring machine (muscular strength, alertness, flexibility, endurance, lung functions and so on), so that the teaching staff and students can use them and train their bodies. 5. Through a refresher education program, urge teachers to understand school health promotion services. 6. Regulate a standard and establish a system of monitoring the physical enviroment of the school (the height of desks and chairs, illumination facilities, ventilation facilities, safe drinking water). 7. Create a check list of health to evaluate improvement.

• Wind and Structures
• /
• v.27 no.6
• /
• pp.381-397
• /
• 2018

Nonlinear behavior in fluid-structure interaction (FSI) of bridge decks becomes increasingly significant for modern bridges with increasing spans, larger flexibility and new aerodynamic deck configurations. Better understanding of the nonlinear aeroelasticity of bridge decks and further development of reduced-order nonlinear models for the aeroelastic forces become necessary. In this paper, the amplitude-dependent and neutral angle dependent nonlinearities of the motion-induced loads are further highlighted by series of computational fluid dynamics (CFD) simulations. An effort has been made to investigate a semi-analytical time-domain model of the nonlinear motion induced loads on the deck, which enables nonlinear time domain simulations of the aeroelastic responses of the bridge deck. First, the computational schemes used here are validated through theoretically well-known cases. Then, static aerodynamic coefficients of the Great Belt East Bridge (GBEB) cross section are evaluated at various angles of attack, leading to the so-called nonlinear backbone curves. Flutter derivatives of the bridge are identified by CFD simulations using forced harmonic motion of the cross-section with various frequencies. By varying the amplitude of the forced motion, it is observed that the identified flutter derivatives are amplitude-dependent, especially for $A^*_2$ and $H^*_2$ parameters. Another nonlinear feature is observed from the change of hysteresis loop (between angle of attack and lift/moment) when the neutral angles of the cross-section are changed. Based on the CFD results, a semi-analytical time-domain model for describing the nonlinear motion-induced loads is proposed and calibrated. This model is based on accounting for the delay effect with respect to the nonlinear backbone curve and is established in the state-space form. Reasonable agreement between the results from the semi-analytical model and CFD demonstrates the potential application of the proposed model for nonlinear aeroelastic analysis of bridge decks.

• Geomechanics and Engineering
• /
• v.24 no.5
• /
• pp.407-418
• /
• 2021

Due to the complexity of the causes of the sliding mass instabilities, landslide susceptibility and hazard evaluation are difficult, but they can be more carefully considered and regionally evaluated by using new programming technologies to minimize the hazard. This study aims to evaluate the landslide hazard zonation in the Tabriz region, Iran. A fuzzy logic-based multi-criteria decision-making method was proposed for susceptibility analysis and preparing the hazard zonation maps implemented in MATLAB programming language and Geographic Information System (GIS) environment. In this study, five main factors have been identified as triggering including climate (i.e., precipitation, temperature), geomorphology (i.e., slope gradient, slope aspect, land cover), tectonic and seismic parameters (i.e., tectonic lineament congestion, distribution of earthquakes, the unsafe radius of main faults, seismicity), geological and hydrological conditions (i.e., drainage patterns, hydraulic gradient, groundwater table depth, weathered geo-materials), and human activities (i.e., distance to roads, distance to the municipal areas) in the study area. The results of analyses are presented as a landslide hazard map which is classified into 5 different sensitive categories (i.e., insignificant to very high potential). Then, landslide susceptibility maps were prepared for the Tabriz region, which is categorized in a high-sensitive area located in the northern parts of the area. Based on these maps, the Bozgoosh-Sahand mountainous belt, Misho-Miro Mountains and western highlands of Jolfa have been delineated as risk-able zones.