• Food Science of Animal Resources
• /
• v.43 no.5
• /
• pp.826-839
• /
• 2023

This study investigated the effects of different charcoals on the occurrence of 16 polycyclic aromatic hydrocarbons (PAHs) in grilled beef steaks and beef patties. Seven different charcoals were used as follows: from oak wood (C1), from orange wood (C2), from Valonia oak wood (C3), from Marabu wood (C4), extruded charcoal from beech wood (C5), from coconut shells (C6), and from hazelnut shells (C7). The grilling times for each charcoal type were 6 min for the beef patties and 7 min for the beef steaks, until the internal temperature reached at least 74℃. The total concentration of 16 PAHs (PAH16) in beef steaks grilled with C1 (35.75 ㎍/kg) and C7 (36.39 ㎍/kg) was higher than that of C3 (23.80 ㎍/kg) and C6 (24.48 ㎍/kg; p<0.05). The highest amounts of PAH16 (216.40 ㎍/kg) were determined in the beef patty samples grilled using C5 (p<0.05). The summation of benzo[a]anthracene, chrysene, benzo[b]fluoranthene and benzo[a]pyrene, referred to as PAH4, was not detected in any of the beef steaks, whereas it was determined in the beef patties grilled with C2 (7.72 ㎍/kg) and C5 (22.95 ㎍/kg; p<0.05). The PAH16 concentrations of the beef patty samples in each charcoal group were significantly higher compared to the beef steaks (p<0.05). To avoid the formation of high PAH levels, the use of extruded charcoal and hazelnut shell charcoal should therefore be avoided when charcoal grilling beef steaks and beef patties, and low-fat meat products should be preferred.

• Journal of Korean Society of Forest Science
• /
• v.61 no.1
• /
• pp.27-36
• /
• 1983

This study was performed to get the basic information on nitric acid pulping of beech wood. In order to reduce the consumption of nitric acid, alkali pretreated woods were applied to a nitric acid pulping process. It consisted of nitric acid treatment to a high residual lignin content and the subsequent delignification with alkali, required far less chemical than the single stage method. At the first stage of nitric pulping, pulp yield descreased with increasing cooking time and 3 percent of nitric acid was more effective on the delignification of wood than 1 or 2 percent. Alkali pretreatment of wood improved significantly the rate of delignification, and 79 percent of the pretreated yield was good enough for excellent delignification. The dissolution of carbohydrate (mainly xylose) was increased with increasing cooking time, especially at the second stage. It would be considered that carbonyl groups introduced to polysaccharides in wood by nitric acid oxidation caused the degradation of carbohydrates.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.43 no.3
• /
• pp.52-58
• /
• 2011

Proton-NMR spectroscopic method was applied to kinetic study of concentrated sulfuric acid hydrolysis reaction, especially focused on 2nd step of acid hydrolysis with deferent reaction time and temperature as main variables. Commercial xylan extracted from beech wood was used as model compound. In concentrated acid hydrolysis, xylan was converted to xylose, which is unstable in 2nd hydrolysis condition, which decomposed to furfural or other reaction products. Without neutralization steps, proton-NMR spectroscopic analysis method was valid for analysis of not only monosaccharide (xylose) but also other reaction products (furfural and formic acid) in acid hydrolyzates from concentrated acid hydrolysis of xylan, which was the main advantages of this analytical method. Higher temperature and longer reaction time at 2nd step acid hydrolysis led to less xylose concentration in xylan acid hydrolyzate, especially at $120^{\circ}C$ and 120 min, which meant hydrolyzed xylose was converted to furfural or other reaction products. Loss of xylose was not match with furfural formation, which meant part of furfural was degraded to other undetected compounds. Formation of formic acid was unexpected from acidic dehydration of pentose, which might come from the glucuronic acid at the side chain of xylan.

• Journal of the Korean Wood Science and Technology
• /
• v.10 no.3
• /
• pp.118-131
• /
• 1982

1. In order to investigate the effect of variation of assembly time on glue bond strength, and to determine the optimum range of assembly time with given glue, this experiment was made at the suggestion of the Wood Technology Laboratory, School of Forestry, Yale University. 2. For this investigation, three-ply-plywoods with 1/22 inch, birch veneer, phenolic resin, and soybean glue were made at the following variation of assembly time, that is, 1, 5, 10, 25, 35, 50, and 70 minutes, under both open and closed assembly manners, and the shear strength test at dry and wet were adoptted. 3. The shear strength and wood failure of each plywood panel constructed at the given assembly time have been illustrated in Tables 1, 2, 3 and 4. It has shown that there is a remarkable tendency, for increasing assembly time to give lower shear strength and wood failure throughout almost all cases. The effective range of assembly time of tested glues in this investigation for both open and closed assembly are summarized in the Table 7. Thus, allowable assembly time for Phenolic resin may be up to 10 minutes under open assembly and up to 50 minutes under closed assembly. For soybean glue, the permissible assembly time may be up to 5 minutes under open assembly and up to 15 minutes under closed assembly. The allowable assembly time for open assembly with the same glue is reduced by approximately one third or more than one third as compared with closed assembly time. This might mean that the closed asembly time for these glues is more practical than the open assembly.

• Journal of Microbiology and Biotechnology
• /
• v.31 no.10
• /
• pp.1438-1445
• /
• 2021

A bifunctional glycoside hydrolase GH78 from the ascomycete Xylaria polymorpha (XpoGH78) possesses catalytic versatility towards both glycosides and esters, which may be advantageous for the efficient degradation of the plant cell-wall complex that contains both diverse sugar residues and esterified structures. The contribution of XpoGH78 to the conversion of lignocellulosic materials without any chemical pretreatment to release the water-soluble aromatic fragments, carbohydrates, and methanol was studied. The disintegrating effect of enzymatic lignocellulose treatment can be significantly improved by using different kinds of hydrolases and phenoloxidases. The considerable changes in low (3 kDa), medium (30 kDa), and high (> 200 kDa) aromatic fragments were observed after the treatment with XpoGH78 alone or with this potent cocktail. Synergistic conversion of rape straw also resulted in a release of 17.3 mg of total carbohydrates (e.g., arabinose, galactose, glucose, mannose, xylose) per gram of substrate after incubating for 72 h. Moreover, the treatment of rape straw with XpoGH78 led to a marginal methanol release of approximately 17 ㎍/g and improved to 270 ㎍/g by cooperation with the above accessory enzymes. In the case of beech wood conversion, the combined catalysis by XpoGH78 and laccase caused an effect comparable with that of fungal strain X. polymorpha in woody cultures concerning the liberation of aromatic lignocellulose fragments.

• Korean Journal of Agricultural Science
• /
• v.9 no.1
• /
• pp.239-249
• /
• 1982

The outlines of superior stands, including species mixed, age classes, canopies, and ecological conditions of the stands, were examined in the forests of west Germany, Sweden, and Netherland. The establishment schemes of tree seed orchards for the production of high genetic quality seed were also investigated in the present study. 1. The meteorological conditions, abundant in precipitation and high in relative humidity, prove it to be oceanic climate characteristics in the Scandinavia located in high latitude and north-western part of Europe. The photo periodical characteristics following to day-length and the frost times determine the patterns of tree growth and distribution as well as the tree adaptability due to bud-setting and bud-flushing in Sweden forest. 2. The European forests are generally characterized by dense multistoried forest type composed of upper stories of tall tree species such as Norway spruce, fir, Scots pine and beech, lower stories of shade tolerant poles and saplings of spruce, fir, beech, and floor vegetations covered with birch, oak and hornbeam etc. 3. The single tree selection method and group shelterwood method are commonly applied for silvicultural system but shelterwood method and clearcutting method practiced partially in limited area. Badischer Femelschlagbetrieb and Bayerischer Femelschlagbetrieb are popularized to the regeneration of Schwarzwald but selection method applied in part. 4. Tree cuttings are properly limited so as not to exceed annual increment volume for the sustained yield and the preservation of ecosystem in European forest management. Land preservation and recreation function are more interested with the promotion of wood production in the forest management. 5. Careful attentions are paid to the reforestation of the introduced exotic species, such as Douglas-fir, red oak, pines from America, Japanese larch, Italian poplar etc., with concern against the insect and pest damage, and the meteorological damage. 6. Some intensive studies on tree improvement, such as selection of plus tree, selection of plus stand for seed collection, provenance trial, progeny test of clone, hybrid seed orchard for clone complexing, are performed in the countries and the great part of the seed required for reforestation are supplied from the seed orchard established in Sweden and Netherland.