• Journal of the Korean Ceramic Society
• /
• 제54권5호
• /
• pp.380-387
• /
• 2017

In this study, unstable CaO was converted into a stable Ca compound by using carbonation in a circulating fluidized bed boiler of fly ash to confirm material usability as cement admixture; also undertaken was carbonation test and mortar to examine chemical and physical change by measuring absorption rate and compressive strength. To investigate the chemical properties of circulating fluidized bed boiler fly ash, XRD and TG-DTA were used to determine how the properties of the reaction product change quantitatively during carbonation. In order to stabilize CaO, carbonation of CaO is considered to be the most desirable process. This is because $CaCO_3$, which is a Ca compound, was produced by carbonate reaction of unstable CaO, and decrease of the absorption rate and improvement of the compressive strength were observed when the carbonated fly ash was replaced with cement.

• Journal of Forest and Environmental Science
• /
• 제15권1호
• /
• pp.89-97
• /
• 1999

This study was carried out to obtain basic data on the kinds of aquatic insects and their living conditions in the mountain stream. The investigation was done in Bongmyung stream. Experimental Forest, Kangwon National University on aquatic insects, anions and river-bed materials. The results are as follows. 1. At every plot surveyed, diversity index, richness index and evenness index of aquatic insects appeared higher at upper stream than at lower stream in erosion control dam. 2. Anion concentrations were almost the same in plots A, B, C, D and E, but plot F at the lower stream showed 1.5 to 89 times higher concentration than the others. 3. In river-bed materials analysed, particle diameter was bigger at the upper stream than at the lower stream. At the down stream of erosion control dam showed high pebble composition ratio. 4. The number of aquatic insects showed the negative relation with the anion concentration and the positive one with the size of river-bed materials. Especially, they were affected much by the distribution chart of boulder.

• Journal of Korea Water Resources Association
• /
• 제31권3호
• /
• pp.291-301
• /
• 1998

The objective of this study is to analyze the characteristics of flow and bed topography with changing bed material in a 180-degree, with constant-radius curved experimental channel. Sand($D_{50}$ = 0.56 mm, s = 2.65) and anthracite($D_{50}$ = 0.26 mm, s = 1.54) were selected as bed materials. The maximum scour depth was found to be about two times for the mean flow depth at the outer bank of bend angle $30^{\circ}~60^{\circ}$, and in case of anthracite, it was found upper part of bend angle $5^{\circ}~15^{\circ}$ than that of sand. Regardless of bed materials the path of maximum streamwise velocity is skewed inwards in the upper part of the bend, the maximum velocity shifts outwards, and it lagged downward as bed roughness increases. The maximum skewed angle of flow grows faster in the smooth bottom than in the rough one, and its value also increases. The secondary flow in anthracite bottom was measured larger than that of sand one, and two cells of secondary flow was found in this experiment.

• Journal of Korea Water Resources Association
• /
• 제49권2호
• /
• pp.83-94
• /
• 2016

Geomorphological, bed material and hydraulic characteristics are basis informations for the planning, design and management of the river in the aspect of flood control and environmental conservation, and it is very important to use these informations for the design of stable channel. In this study, dominant discharge was selected, geomorphological and hydraulic characteristics were analyzed using that discharge and also the characteristics of bed materials distribution were analyzed and bed materials-flow resistance relationship was evaluated, for the upstream section of Namgang dam. The dominant discharge was estimated a return period of approximately 1.5 year and stream type were classified Segment 1 and Segment 2 in this stream. Also, the frequency of riffle-pool showed 4.4 because this study area has the characteristics of natural channel that have not channel-crossing structures. In dominant discharge, according to the results that analyzed relationship between $h/d_{50}$ and $V/u_*$ to calculate flow resistance by bed materials, Julian's formula showed to appropriate in channel where is relatively close to natural river and is predominantly consisted of gravel, cobble, boulder and rock in mountain, and it was confirmed that the image processing methodology will be easily applied to the analysis of bed materials distribution in future.

• Journal of Powder Materials
• /
• 제30권2호
• /
• pp.146-155
• /
• 2023

The Ti-6Al-4V lattice structure is widely used in the aerospace industry owing to its high specific strength, specific stiffness, and energy absorption. The quality, performance, and surface roughness of the additively manufactured parts are significantly dependent on various process parameters. Therefore, it is important to study process parameter optimization for relative density and surface roughness control. Here, the part density and surface roughness are examined according to the hatching space, laser power, and scan rotation during laser-powder bed fusion (LPBF), and the optimal process parameters for LPBF are investigated. It has high density and low surface roughness in the specific process parameter ranges of hatching space (0.06-0.12 mm), laser power (225-325 W), and scan rotation (15°). In addition, to investigate the compressive behavior of the lattice structure, a finite element analysis is performed based on the homogenization method. Finite element analysis using the homogenization method indicates that the number of elements decreases from 437,710 to 27 and the analysis time decreases from 3,360 to 9 s. In addition, to verify the reliability of this method, stress-strain data from the compression test and analysis are compared.

• Journal of Powder Materials
• /
• 제26권3호
• /
• pp.225-230
• /
• 2019

To develop Taraxacum platycarpum extract (TP)-loaded particles for tablet dosage form, various TP-loaded particles composed of TP, dextrin, microcrystalline cellulose (MCC), silicon dioxide, ethanol, and water are prepared using a spray-drying method and fluid-bed-drying method. Their physical properties are evaluated using angle of repose, Hausner ratio, Carr's index, hardness, disintegrant time, and scanning electron microscopy. Optimal TP-loaded particles improve flowability and compressibility. Furthermore, 2% silicon dioxide gives increased flowability and compressibility. The formula of TP-loaded fluid-bed-drying particles at a TP/MCC/silicon-dioxide amount of 5/5/0.2 improves the angle of repose, Hausner ratio, Carr's index, hardness, and disintegrant time as compared with the TP-loaded spray-drying particles. The TP-loaded fluid-bed-drying particles considerably improve flowability and compressibility ($35.10^{\circ}$ vs. $40.3^{\circ}$, 0.97 vs. 1.17, and 18.97% vs. 28.97% for the angle of repose, Hausner ratio, and Carr's index, respectively), hardness (11.34 vs. 4.7 KP), and disintegrant time (7.4 vs. 10.4 min) as compared with the TP-loaded spray-drying particles. Thus, the results suggest that these fluid-bed-drying particles with MCC and silicon dioxide can be used as powerful particles to improve the flowability and compressibility of the TP.

• Journal of the Korean housing association
• /
• 제5권2호
• /
• pp.87-97
• /
• 1994

The purpose of this study are to obtain basic materials that can be fulfil effective using of space by consider living behavior and attitude, a furniture usage and a space usage according to the usage of bed in An-Bang. It also suggests a plan about a method of furniture usage that is reflected resident’s living behavior and attitude, desire, consciousness through the space evaluation. The major findings of this study can be summarized as follow : 1, The case of husband’s age was less than 47, and the educational level of husband and wife was above a university graduate, the percentage of possession of bed was high. 2. According to the usage of bed, this study showed difference of furniture usage, and that of life action. 3. According to the usage of bed, there were significant differences in the luxury by result of the space evaluation. 4. Also, there were significant differences in a satisfaction of atmosphere, and an area by satisfaction of furniture usage. 5. According to the usage of bed, the influence of each independent variable appeared differently by result of regression analysis to see the space evaluation effect on space satisfaction.

• Plant Journal
• /
• 제14권2호
• /
• pp.33-38
• /
• 2018

The CFB boilers technology is facing a number of challenges. Among them, boiler tube erosion, sintering by bed inventory overheating and high self consumed service power are major ones. This study was conducted to obtain allowable bed inventory with the Yeosu Power Plant, a 300 MW class CFB boiler. For the test, bed pressure was reduced from design pressure of 4.5 KPa to 2.5 KPa by reducing bed inventory, at fixed turbine output, coal consumption rate and air flow. Consequently, reducing the lower bed inventory is effective to decrease bed temperature but excessive reducing might increase bed temperature due to lack of circulating fluidized materials. Also, in case of the Yeosu Plant boiler using subbituminous coal as its primary fuel, its bed temperature change is highly affected by not only the amount of bed inventory, but also the boiler capacity and coal contents.

• Journal of Powder Materials
• /
• 제29권5호
• /
• pp.390-398
• /
• 2022

Recently, considerable attention has been given to nickel-based superalloys used in additive manufacturing. However, additive manufacturing is limited by a slow build rate in obtaining optimal densities. In this study, optimal volumetric energy density (VED) was calculated using optimal process parameters of IN718 provided by additive manufacturing of laser powder-bed fusion. The laser power and scan speed were controlled using the same ratio to maintain the optimal VED and achieve a fast build rate. Cube samples were manufactured using seven process parameters, including an optimal process parameter. Analysis was conducted based on changes in density and melt-pool morphology. At a low laser power and scan speed, the energy applied to the powder bed was proportional to ${\frac{P}{\sqrt{V}}}$ and not ${\frac{P}{V}}$. At a high laser power and scan speed, a curved track was formed due to Plateau-Rayleigh instability. However, a wide melt-pool shape and continuous track were formed, which did not significantly affect the density. We were able to verify the validity of the VED formula and succeeded in achieving a 75% higher build rate than that of the optimal parameter, with a slight decrease in density and hardness.

• Transactions of the Korean hydrogen and new energy society
• /
• 제24권6호
• /
• pp.535-542
• /
• 2013

To enhance the performance of SEWGS system by holding the WGS catalyst in a SEWGS reactor using bed inserts, effect of bed insert geometry on CO conversion of WGS catalyst was measured and investigated. Small scale fluidized bed reactor was used as experimental apparatus and tablet shaped WGS catalyst and sand particle were used as bed materials. The cylinder type and the spring type bed inserts were used to hold the WGS catalysts. The CO conversion of WGS catalyst with the change of steam/CO ratio was determined based on the exit gas analysis. Moreover, gas flow direction was confirmed by bed pressure drop measurement for each case. The measured CO conversion using the bed inserts showed high value comparable to previous results even though at low catalyst content. Most of input gas flowed through the bed center side when we charged tablet type catalyst into the cylinder type bed insert and this can cause low $CO_2$ capture efficiency because the possibility of contact between input gas and $CO_2$ absorbent is low in this case. However, the spring type bed insert showed good reactivity and good distribution of gas, and therefore, the spring type bed insert was selected as the best bed insert for SEWGS process.