• 한국지반환경공학회 논문집
• /
• 제20권8호
• /
• pp.5-12
• /
• 2019

상부구조물은 여러 개의 말뚝 기초를 말뚝 캡으로 연결한 무리말뚝이 사용되고 있다. 무리말뚝 설계 시 상부구조물의 연직 및 수평하중은 말뚝 기초가 지지할 뿐 말뚝 캡의 지지효과는 무시하였다. 그러나 최근 상부구조물의 연직하중에 대한 안정성 범위에서 말뚝 기초의 사용량을 줄이기 위해 말뚝 캡의 지지효과를 반영하기 위한 연구가 진행되고 있으나 수평하중에 대한 말뚝 캡의 지지효과에 관한 연구는 미비한 실정이다. 이에 본 연구에서는 수평 지진 하중을 받는 무리말뚝에서 말뚝 캡의 변화가 무리말뚝에 미치는 영향을 확인하기 위해 상부구조물을 지지하는 무리말뚝의 말뚝 캡 크기를 변화시켜 진동대 모형실험을 수행하였다. 그 결과 말뚝 캡의 크기가 상부구조물 및 무리말뚝의 동적 거동에 영향을 미치는 것으로 확인되었으며, 말뚝 캡의 크기가 증가할수록 지반 구속 효과로 인해 지반과 말뚝 기초가 일체 거동하는 것으로 나타났다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 봄 학술발표회 논문집
• /
• pp.307-314
• /
• 2001

The bearing capacity of drilled shafts that take excavation by Percussion Rrotary Drilling(PRD) into consideration was evaluated using static and dynamic pile load tests. The emphasis was on quantifying the allowable bearing capacity and point load-transfer at the pile tip on seven instrumented steel piles. Of the seven instrumented piles, five piles are placed to the bottom of the excavation by rotary and pushing into the final depth of the excavation, as opposed to the two driven piles. Based on the results obtained, it is shown that the skin friction mobilized by PRD is much greater than point resistance, whereas in driven piles, the point resistance is greater than skin friction. It is also found that much greater pile capacity was proved in the case of drilled shafts, compared to the driven piles and thus, the excavation by rotary drilling gives reliable pile capacity required to design axially loaded piles.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1988년도 학술세미나 강연집
• /
• pp.71-123
• /
• 1988

The aim of this paper is to examine the end bearing capacity of a pile in cohesionless soils. The ode of failure of soil due to pile installation is assumed from experimental observation of actual soil deformation. A new solution is proposed complying with the assumed mode of failure by employing the theory of cavity expansion. The effect of curvature of failure envelope is studied in relation to tile proposed solution. The influence of a curved failure envelope becomes larger with increasing degree of curvature and the level of confining stress. This effect in some cases or reduce the end bearing capacity by tore the 80 percent compared with that given by a straight failure envelope. For practical application of tile proposed solution, the method of determining the average volume change in the plastic zone is re-evaluated. The proposed solution is confirmed by comparing the theoretical values with experimental results obtained from model pile tests in a calibration chamber. The comparison shows that the proposed solution provides a reasonable prediction of end bearing capacity for both weak and strong grained soils.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.559-568
• /
• 2010

Recently, because of mega foundations and grand bridges, the foundations require significant bearing capacity. In this study, bearing capacity of high strength steel pipe pile with an extended head (HSP) is calculated on the basis of domestic criteria and Japanese criteria. And bearing capacity of HSP is investigated based on 3 field tests. In comparison with the results of analysis and tests, it is shown that the field test results are bigger than analysis results. Therefore, it is proposed to estimate bearing capacity of HSP.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 기초기술학술발표회
• /
• pp.57-76
• /
• 2002

As piling works in urban area increasing, SIP which is low noise & vibration piling method is taking place of driven pile which has good bearing charateristics and economics. Since SIP has been used for more than 15 years and it's application is increasing year by year, however, accurate analysis of bearing mechanism of SIP is not enough. So the design of SIP is much more conservative than driven pile. This paper is aimed to analyse the bearing charateristics of 103 SIPs constructed in Korea to give rational design criteria. Research result shows that bearing capacity of SIP is 40% lower than that of driven pile and conservative Meyerhof(equation omitted) method produced closer result to load test results than other design method. And this result show that to use optimised design criteria for the economic SIP design, quality control criteria must be settled down to produce high in-situ bearing capacity.

• 한국해양공학회지
• /
• 제25권6호
• /
• pp.35-41
• /
• 2011

Recently, as large structures, which should support large design loads have been constructed, the study on the large diameter composite pile becomes necessary. The large diameter composite pile has the diameter over 700mm and consists of two parts of the upper steel pipe pile and the lower PHC pile by a mechanical joint. In this research, to analyze the bearing capacity and the material strength of the composite pile, three dimensional numerical analyses were performed. First, the numerical modeling method was verified by comparing the calculated load-movement curves of the pile with those of the field pile load tests. Then, a total of twelve analyses were performed by varying pile diameter and loading direction for three pile types of PHC, steel pipe and composite piles. The results showed that the vertical and the horizontal load-movement curves of the composite pile were identical with those of the steel pipe pile and the horizontal material strength of the composite pile was 60-80% larger than that of the PHC pile.

• 산업기술연구
• /
• 제22권B호
• /
• pp.191-197
• /
• 2002

This paper is experimental and numerical research results of performing centrifuge model tests to investigate the geotechnical engineering behavior of slag compaction pile as a substitute of sand compaction pile. In order to find the geotechnical engineering characteristics of the soft clay and the slag used in centrifuge model experiments, basic soil property tests, consolidation test, permeability tests and triaxial compression tests were performed. For centrifuge model tests, slags with changing relative density were used and their bearing capacity, stress concentrations in between pile and soft clay, settlement characteristics, and failure modes were investigated. As a results of centrifuge model tests, it was found that the bearing, capacity of model was increased with increasing density of slag pile and general shear failures were occured. Miniature soil pressure gauges were installed on model pile and soft ground respectively and thus vertical stress acting on them were measured. Stress concentration ratio was found to be in the range of 2.0~3.0. Bearing capacity obtained from the model test with slag was greater than that from the model test with a sand having the identical layout to each other. Thus it was confirmed the slag was an appropriate substitution of pile for sand.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1998년도 가을 학술발표회 논문집
• /
• pp.199-208
• /
• 1998

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1996년도 가을 학술발표회 논문집
• /
• pp.337-344
• /
• 1996

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.536-545
• /
• 2006

In this study the behavior of piles with an extended head is invested experimentally using reduced-scale model tests. Special attention is given to verifying the increase of end bearing capacity of piles with spreading head. Model piles and extended head plates made of steel pipe were used in this study. Bearing capacity of piles is regarded as only end bearing capacity. The study analyzed the tendency of single and group pile of bearing capacity compared with the existing PHC pile, and examined optimum effect of extended head.