• Journal of the Korean Electrochemical Society
• /
• v.11 no.4
• /
• pp.268-272
• /
• 2008

$LiFePO_4$ material was synthesized by electrospinning method to obtain optimal particle size($50{\sim}100\;nm$) without carbon coating or ball milling. This material showed an orthorthombic structure with Pnma space group without any impurities, such as FeP or $Fe_2P$, in the XRD pattern. The particle morphology and particle shape were observed by SEM analysis. Li/$LiFePO_4$ cell showed a high initial discharge capacity of 135 mAh/g, at current density of $0.1\;mA/cm^2$ with a cut-off voltage of 2.8 to 4.0V. This cell exhibited a perfect cycle performance over 99.9% cycle retention rate up to 50 cycles.

• Asian-Australasian Journal of Animal Sciences
• /
• v.25 no.11
• /
• pp.1605-1610
• /
• 2012

Two experiments were conducted to study the effects of red pepper (Capsicum frutescens) powder or red pepper pigment on the performance and egg yolk color of laying hens. In Exp. 1, 210, thirty-wk old, Hy-line Brown laying hens were fed one of seven diets containing 0.3, 0.6, 1.2, 2.0, 4.8 or 9.6 ppm red pepper pigment or 0.3 ppm carophyll red. Each diet was fed to three replicate batteries of hens with each battery consisting of a row of five cages of hens with two hens per cage (n = 3). In Exp. 2, 180, thirty-wk old, Hyline Brown laying hens, housed similarly to those in Exp. 1, were fed an unsupplemented basal diet as well as treatments in which the basal diet was supplemented with 0.8% red pepper powder processed in a laboratory blender to an average particle size of $300{\mu}m$, 0.8% red pepper powder processed as a super fine powder with a vibrational mill ($44{\mu}m$) and finally 0.8% red pepper powder processed as a super fine powder with a vibrational mill but mixed with 5% $Na_2CO_3$ either before or after grinding. A diet supplemented with 0.3 ppm carophyll red pigment was also included (n = 3). In both experiments, hens were fed the red pepper powder or pigment for 14 days. After feeding of the powder or pigment was terminated, all hens were fed the basal diet for eight more days to determine if the dietary treatments had any residual effects. In Exp. 1, there were no differences in egg-laying performance, feed consumption or feed conversion ratio due to inclusion of red pepper pigment in the diet. Average egg weight was higher (p<0.05) for birds fed 1.2, 2.4 or 9.6 ppm red pepper pigment than for birds fed the diet containing 0.3 ppm red pepper pigment. On d 14, egg color scores increased linearly as the level of red pepper pigment in the diet increased. In Exp. 2, feeding red pepper powder did not affect egg-laying performance, feed consumption or feed conversion ratio (p>0.05). However, compared with the control group, supplementation with all of the red pepper powder treatments increased egg weight (p<0.05). All the red pepper powder treatments also increased (p<0.05) the yolk color score compared with the control. The results of the present study suggest that both red pepper powder and pigment are effective feed additives for improving egg yolk color for laying hens.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.8
• /
• pp.1588-1596
• /
• 2015

In the Internet of Things (IoT), resource-constrained devices such as sensors are capable of communicating and exchanging data over the Internet. The IETF standard group has specified an application protocol CoAP, which uses UDP as a transport protocol, allows such a lightweight device to transmit data. Also, the IETF recommended the DTLS binding for securing CoAP. However, additional features should be added to the DTLS protocol to resolve several problems such as packet loss, reordering, fragmentation and replay attack. Consequently, performance of DTLS is worse than TLS. It is highly required for lightweight devices powered by small battery to design and implement a security protocol in an energy efficient manner. This paper thus discusses about DTLS performance in the perspective of energy consumption. To analyze the performance, we implemented IEEE 802.15.4 based test network consisting of constrained sensor devices in the Cooja simulator. We measured energy consumptions required for each of DTLS client and server in the test network. This paper compares the energy consumption and amount of transmitted data of each flight of DTLS handshake, and the processing and receiving time. We present the analyzed results with regard to code size, cipher primitive and fragmentation as well.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.3
• /
• pp.569-575
• /
• 2020

Recently, research on renewable energy technologies has come into the spotlight due to rising concerns over the depletion of fossil fuels and greenhouse gas emissions. Demand for portable electronic and wearable devices is increasing, and electronic devices are becoming smaller. Energy harvesting is a technology for overcoming limitations such as battery size and usage time. In this paper, the V-I characteristic curve and internal resistance of thermal electric devices were analyzed, and MPPT control methods were compared. The Perturbation and Observation (P&O) control method is economically inefficient because two sensors are required to measure the voltage and current of a Thermoelectric Generator(TEG). Therefore, this paper proposes a new MPPT control method that tracks MPP using only one sensor for the regulation of the output voltage. The proposed MPPT control method uses the relationship between the output voltage of the load and the duty ratio. Control is done by periodically sampling the output voltage of the DC-DC converter to increase or decrease the duty ratio to find the optimal duty ratio and maintain the MPP. A DC-DC converter was designed using a cascaded boost-buck converter, which has a two-switch topology. The proposed MPPT control method was verified by simulations using PSIM, and the results show that a voltage, current, and power of V=4.2 V, I=2.5 A, and P=10.5 W were obtained at the MPP from the V-I characteristic curve of the TEG.

• Applied Chemistry for Engineering
• /
• v.21 no.5
• /
• pp.590-592
• /
• 2010

Li-Mn spinel ($LiMn_2O_4$) is prepared by a hydrothermal process with K-Birnessite ($KMnO_4{\cdot}yH_2O$) as a precursor. The K-Birnessite obtained via a hydrothermal process with potassium permanganate [$KMnO_4$] and urea [$CO(NH_2)_2$] as starting materials are converted to Li-Mn spinel nanoparticles reacting with LiOH. The molar ratio of LiOH/K-Birnessite is adjusted in order to find the effect of the ratio on the structural, morphological and electrochemical performances of the Li-Mn spinel. X-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDS), and thermogravimetry (TG) are used to investigate the crystal structure and morphology of the samples. Galvanostatic charge and discharge are carried out to measure the capacity and rate capability of the Li-Mn spinel. The capacity shows a maximum value of $117\;mAhg^{-1}$ when the molar ratio of LiOH/K-Birnessite is 0.8 and decreases with the increase of the ratio. However the rate capability is improved with the increase of the ratio due to the reduction of the particle size.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.8
• /
• pp.56-63
• /
• 2010

This work proposes a 12b 100MS/s 0.13um CMOS pipeline ADC for battery-powered mobile video applications such as DVB-Handheld (DVB-H), DVB-Terrestrial (DVB-T), Satellite DMB (SDMB), and Terrestrial DMB (TDMB) requiring high resolution, low power, and small size at high speed. The proposed ADC employs a three-step pipeline architecture to optimize power consumption and chip area at the target resolution and sampling rate. A single shared and switched op-amp for two MDACs removes a memory effect and a switching time delay, resulting in a fast signal settling. A two-step reference selection scheme for the last-stage 6b FLASH ADC reduces power consumption and chip area by 50%. The prototype ADC in a 0.13um 1P7M CMOS technology demonstrates a measured DNL and INL within 0.40LSB and 1.79LSB, respectively. The ADC shows a maximum SNDR of 60.0dB and a maximum SFDR of 72.4dB at 100MS/s, respectively. The ADC with an active die area of 0.92 $mm^2$ consumes 24mW at 1.0V and 100MS/s. The FOM, power/($f_s{\times}2^{ENOB}$), of 0.29pJ/conv. is the lowest of ever reported 12b 100MS/s ADCs.

• Journal of the Korean Electrochemical Society
• /
• v.7 no.4
• /
• pp.183-188
• /
• 2004

In order to develop polymer electrolyte for lithium/sulfur batteries, highly microporous P(VdF-HFP) membranes were prepared by phase inversion method. Porous structure was controlled by extracting NMP with mixture of deionized water and methanol. Porous structure of the membranes was observed with SEM. Polymer electrolytes were prepared by soaking the porous membranes in 1M $LiCF_3SO_3-TEGDME/EC$. The ionic conductivity of polymer electrolyte was found to be at high as $2\times10^{-3}S/cm$ when the polymer membrane extracted by $80\%$ methanol was used. The microporous polymer electrolyte optimized in this work displayed high ionic conductivity, uniform pore size, low interfacial resistance and stable ionic conductivity with storage time. The ionic conductivity of polymer electrolytes was measured with various lithium salts, and the conductivity showed $3.3\times10^{-3}S/cm$ at room temperature when $LiPF_6$ was used as a lithium salt.

• Journal of the Korea Society of Computer and Information
• /
• v.18 no.5
• /
• pp.1-8
• /
• 2013

Smartphone enables diverse applications to be used in mobile environments. In spite of the high performance of smartphones, battery life has become one of the major constraints in mobility. Therefore, power efficiency of the smartphone is one of the most important factors in determining the efficiency of the smartphone. In this paper, in order to analyze the power efficiency of the smartphone, we have various experiments according to several configuration parameters such as processor, display and OS. We also use diverse applications. As a result, power consumption is dependent on the processor complexity and display size. However, power consumption shows the unpredictable pattern according to the OS. Smartphone using android OS consumes high power when internet and image processing applications are executed, but It consumes low power when music and camera applications are executed. In contrary, smartphone based on iOS consumes high power when game and internet applications are executed but it consumes low power when camera and processing applications are executed. In general, smartphone using iOS is more power efficient than smartphone based on android OS, because smartphone using iOS is optimized in the perspective of the hardware and OS.

• Journal of Aerospace System Engineering
• /
• v.11 no.5
• /
• pp.65-75
• /
• 2017

This study proposes development of 3U CubeSat standard platform whose function and performance are verified via KAUSAT-5 development. 3U CubeSat platform specification was selected for the design of 3U Cubesat standard platform by examining existing CubeSat and state-of-art technology, and consequently a universally usable 3U CubeSat platform was designed. Standard platform was manufactured in 1.5U size and developed with a modular concept to be able to add and expand payloads and ADCS actuators for meeting the user's needs. In addition, in case of the power system, the solar panel, the battery, and the deployment mechanism are designed to be configured by the user. In the mechanical system design of a standard platform, subsystem and micro equipment functions/performance could be integrated and miniaturized on micro-sized PCBs and maximized electrical capability to accommodate multiple payloads. In the development of the 3U CubeSat, the satellite platform adopts the developed standard platform, which can reduce the cost and schedule for the whole satellite development by reducing the additional function verification.

• The Journal of the Convergence on Culture Technology
• /
• v.6 no.4
• /
• pp.813-818
• /
• 2020

Recently, with the rapid increase in technology and users of smart devices, the smart watch market has grown, and its utility and usability are continuously expanding. The strengths of smartwatches are wearable portability, application immediacy, data diversity and real-time capability. Despite these strengths, smartwatches have limitations such as battery limitations, display and user interface size limitations, and memory limitations. In addition, there is a need to supplement developers and standard devices, operating system standard models, and killer application modules. In particular, monitoring and application of user's biometric information is becoming a major service for smart watches. The biometric information of such a smart watch generates a large amount of data in real time. In order to advance the biometric information service, stable peer-to-peer transmission of sensing data to a remote smartphone or local server storage must be performed. We propose a synchronization method to ensure wireless remote peer-to-peer transmission stability in a smart watch system. We design a wireless peer-to-peer transmission process based on this synchronization method, analyze asynchronous transmission process and proposed synchronous transmission process, and propose a transmission efficiency method according to an increase in transmission amount.