• 한국연소학회:학술대회논문집
• /
• 대한연소학회 2003년도 제27회 KOSCO SYMPOSIUM 논문집
• /
• pp.109-113
• /
• 2003

Low pressure or vacuum carburizing(LPC) has undergone major further developments since 1980 and now it has achieved industrial maturity. The advantage of low pressure vacuum carburizing over gas carburizing is not only the creation of surface entirely free of oxide and environmentally friendly but also a reduction in batch times, lower gas and energy consumption and the prevention of soot. In this study the experiment was carried out to investigate the effects of vacuum atmosphere in the heating furnace. Heat transfer rate and uniformity of temperatures of test samples in the pressure range of a few 0.1torr was examined on a test charge of 100kg. It is found that the fuel saving rate due to decreasing heating time reach to 20% in the vacuum heating mode as compared with atmospheric heating mode. Also the uniformity of temperatures in the samples was improved significantly in the vacuum heating mode. Also the effects of the RC fan for stirring atmosphere inside furnace was examined. Results shows RC fan appears to provide a reasonable tool for improving uniformity of temperature in the atmospheric heating mode.

• 한국세라믹학회지
• /
• 제15권4호
• /
• pp.213-223
• /
• 1978

The purpsoe of this study was to produce domestic stamping materials; sling mass which could be used as unburned refractory for iron melt'ladle. Batch compositions were based on Belgian Ladelite; mineral compositions were composed of 84 wt% of quartz and 16 wt% of clay, and particle sizes were divided into 12 wt% of 1410/297㎛, 18wt% 297/149㎛, 20wt% of 149/74㎛, 11wt% 74/44㎛ and 39wt% 44㎛ under. The effect of variable batch compositions were also investigated such as substitution of pyrophylite or industrial grade alumina for quartz and of zircon for portion of quartz and clay, increase of clay and addition on sericite. Samples were pressed at 100kg/㎠ with 7.4wt% of water or 7.4wt% of 4 wt% PVA solution. Dried and Fired properties of samples such as linear shrinkage, apparent porosity, modulus of rupture, refractoriness and corrosion resistance to blast furnace slag were investigated. The results are summarized as follows. 1. Dried samples are shrinked, but fired at 700-1400℃ expanded. Samples fired at 700-1000℃ and 1200-1400℃ tended to expand with incresing of firing temperature, but fired at 1000-1200℃ tended to shrink with increase of firing temperature. 2. Apparent porosity of samples fired at 700℃ is increased, but fired at 1200-1400℃ decreased with increasing of firing temperature. 3. Modulus of rupture of samples fired at 700℃ is decreased, but fired at above 700℃ increased with increasment of firing temperature. 4. Dried samples with 7.4 wt% of 4 wt% PVA solution better improve modulus of rupture than with 7.4 wt% of water, but the firing strength of the sampels fired at 700-1000℃ is showed reversely. 5. In quartz-clay system, mineral phases of samples fired at above 1200℃ are consisted of α-quartz, α-cristobalite and mullite. Respectively as firing temperature was rising up, intensity of α-cristobalite and mullite is in creased. 6. Quartz-Kibushi clay system, Kimcheun quartz(substitutuion of portion of industrial grade alumina for quartz) Hampyeung clay system and pyrophyllite-clay system are better in corrosion resistance to blast furnace slag than burned pyrophyllite brick. 7. 84 wt% of pyrophyllite-16wt% of clay system is superior in modulus of rupture and corrosion resistance to blast furnace slag to 84 wt% of quartz-16 wt% of clay system.

• Journal of Advanced Marine Engineering and Technology
• /
• 제18권1호
• /
• pp.114-122
• /
• 1994

A cold temperature control system for the BAF(batch annealing furnace) has been established in order to reduce energy consumption to imrpove productivity and stabilize the properties of products. Therefore we confirmed a relation between annealing cycle time and atmospheric gas, changing annealing cycle time according to BAF temperature with time during heating and actual temperature measurements cold spot during soaking. The results of the temperature variation effect on the batch annealing are as follows. 1) Cooling rate is increasing gradually with increasing atmospheric gas flow, but heating rate is hardly increasing without atmospheric gas component. Heating time is reduced to one half with increasing atmospheric gas flow rate and changing of atmospheric gas component from HNx to Ax gas and annealing cycle time is reduce to 2.7 times. 2) With enlarging the difference between furnace temperature and soaking temperature at the HNx BAF, heating time becomes short, but cooling time is indifferent. 3) If temperature difference of 300.deg. C in the temperature change of cold spot according to the annealing cycle control temperature, Hi-CON/H2BAF is interchanging at each other at 26hours, but HNxBAF at 50 hours. 4) Soaking time at batch annealing cycle determination is made a decision by the input coil width, and soaking time for quality homogenization of 1219 mm width coil must be 2.5 hours longer then that of 914mm width coil for the same coil weight at Hi-CON/H2BAF. But, it is necessary to make 2 hours longer at HNxBAF.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1997년도 추계학술대회 논문집
• /
• pp.101-107
• /
• 1997

Development on the mechanical properties of steel sheet for the automobile body panel is very important in the BAF(Batch annealing furnace) annealing process. Because of the heat treatment method in the BAF, mechanical properties was decided on the heat treatment method of the coil. So, we tested on the development of mechanical properties according to heat treatment method at the annealing furnace using the Ax atmospheric gas and the HNx atmospheric gas. As a result of several investigations. We confirmed the following characteristics ; mechanical properties was changed under the influence of the annealing cycle, the heat treatment method and the atmospheric gas. And, elongation in the HNx BAF was better than the Ax BAF. Finally, most important thing in the BAF is using proper annealing cycle in order to get a good quality.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2002년도 추계학술발표회
• /
• pp.96-98
• /
• 2002

Furnace slag, a steel industry waste, has been converted into an inexpensive and efficient adsorbent. The product obtained has been utilized for the removal of arsenic from ground water. Kinetic studies have bepn described with the mechanism of adsorption The results from batch studies showed that the As(III) can be removed from the ground water within the pH range 3-7 However the maximum removal was experienced at pH 7.0. Equilibrium was attained within 24 hours. Adsorption data of arsenic correlate well with the Freundlich and Langmuir adsorption models. The maximum sorption capacity as calculated using Freundlich adsorption isotherm was found to be of 0.004 mg g-1 at pH 7 and $25^{\circ}C$.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.1136-1139
• /
• 2009

Recently, various Ni doping systems and thermal annealing systems have been developed for fabrication of polycrystalline silicon film using SGS (super grain silicon) for medium and largesize AMOLED panels. In this study, we compare the potential of Ni doping systems including ALD (atomic layer deposition), AMD (atmospheric metal deposition), in-line sputter, and crystallization annealing systems including batch type furnace, inline furnace, and RTA (rapid thermal annealing) developed for the SGS method. Additional requirements for those systems to be used for mass production of large AMOLED TVs are suggested based on evaluation results for both poly-Si films and TFT backplanes.

• 한국정밀공학회지
• /
• 제15권7호
• /
• pp.69-77
• /
• 1998

Development on the mechanical properties of steel sheet for the automobile body panel is very important in the BAF(Batch annealing furnace) annealing process. Because of the heat treatment method in the BAF, mechanical properties were decided on the heat treatment method of the coil. So, we tested on the development of mechanical properties according to heat treatment method at the annealing furnace using the In atmospheric gas($H_2$ : 75%, $N_2$ : 25%) and the HNx atmospheric gas($H_2$ : 5%, $N_2$ : 95%) We confirmed the following characteristics, mechanical properties were changed under the influence of the annealing cycle and the atmospheric gas. And, we have some result according to heat treatment method. Elongation of the mechanical properties in the HNx BAF is higher than the Ax BAF. But tensile strength and hardness is higher than the HNx BAF.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.417-417
• /
• 2012

For desired optical properties of QDs, it is very important to reduce the presence of defects on their surfaces. Passivation of surface defects using larger band gap materials is the most effective way. Some groups successfully synthesized Cd based multi-shell structured quantum dots and improved its optical properties. However, its productivity has limit because of the amounts of glass ware and space. In this research, we try to synthesize Cd based multi-shell structured nanocrystal quantum dots to overcome demerits of conventional batch synthetic method. This reactor composed pump, SUS reaction part (3.2 mm stainless steel and furnace) and batch mixer. We successively synthesized CdSe/CdS/ZnS quantum dot at this reactor in one step.

• 한국세라믹학회지
• /
• 제14권2호
• /
• pp.88-94
• /
• 1977

Zircon sand of two different particle distribution with 2 percent of ground pyrophyllite were adoted to prepare the dense specimens of the stopper nozzle for the tundish. The molding pressure of $600kg/cm^2$ brought about the superior properties to those obtained t the pressure of $300kg/cm^2$, and as the firing temperatures were increased from $1, 350^{\circ}C$ to $1, 600^{\circ}C$, the better characteristics resulted. The addition of 2 percent $MgCr_2O_4$ to zircon pyrophyllite batch was more effective in corrosion-resistance to the blast furnace-slag.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 전력전자학술대회 논문집
• /
• pp.94-96
• /
• 2001

As a batch Type device, this machine is contrive to seal glass plates for plasma BLU (Back Light Unit) by indirect heating from electric heaters. In order to maintain the heating / cooling Chambers clean, this machine uses a muffle formation. The components of the machine are listed bellow.