• 비파괴검사학회지
• /
• 제2권2호
• /
• pp.9-16
• /
• 1983

There are two weak points in a high pressure vessel, one is a corner, the other is a crack on the base. In order to evaluate safety of a department of a corner and a crack like a starfish on the base in a high pressure vessel (working pressure: $130kg/cm^{2}$), which was made by Marison's Process, we analyzed stress by strain gauge, measured thickness and hardness by ultrasonic testing, and were able to test pressure by water pressure from nondestructive testing. Also destructive testings were applied to measure thickness and to observe microstructure and chemical composition of a corner on the base. From the results of the experiment, values of experiment were satisfied with a condition of application. But, it is considered that a crack on the base is to be investigated with more by Fracture Mechanics.

• Wind and Structures
• /
• 제3권4호
• /
• pp.279-289
• /
• 2000

The main purpose of this paper is to demonstrate the necessity of considering wind load combinations even for low-rise buildings. It first discusses the overall quasi-static wind load effects and their combinations to be considered in structural design of low-rise buildings. It was found that the maximum torsional moment closely correlates with the maximum along-wind base shear. It was also found that the instantaneous pressure distribution causing the maximum along-wind base shear was quite similar to that causing the maximum torsional moment, and that this asymmetric pressure pattern simultaneously accompanies considerable across-wind and torsional components. Secondly, the actual wind pressure distributions causing maximum quasi-static internal forces in the structural frames are conditionally sampled and their typical pressure patterns are presented.

• 한국도로학회논문집
• /
• 제13권2호
• /
• pp.21-29
• /
• 2011

최근 들어 온난화 등의 영향으로 태풍이나 집중호우가 빈번히 발생하고 있으며 이로 인한 산지 도로의 산사태, 토석류, 상향침투수압 등에 의한 인명, 시설물 피해도 극심하게 나타나고 있다. 산지 도로의 상향침투수압은 심각한 포장 파손을 발생시키기도 한다. 산지 측의 높은 지하수위로 인한 상향침투수압을 감소시키기 위해서는 지하배수공법이 매우 효과적 이라고 판단된다. 지하배수 공법을 원활하게 작동하기 위해서는 배수기층이 적합한 투수계수와 지지력을 갖추어야 한다. 따라서 본 연구에서는 적절한 투수성과 지반 지지력을 확보할 수 있는 최적의 배수기층 입도에 대한 연구를 수행하였다.

• 대한치과기공학회지
• /
• 제30권2호
• /
• pp.47-56
• /
• 2008

This is a research for thickness change of denture base according to the shape of sprue & investment position of denture base in flask when injecting polyamid base resin for flexible partial denture as a part of study for Valplast among the flexible partial denture with a nylon base. It has been introduced several kinds of flexible partial denture product with a nylon base, but Valplast is the most widely used product among them. Valplast has been the most generally used material today since developed in 1950s in the United States as a material for flexible partial denture. Valplast is much more aesthetic than general metal-acrylic partial denture due to its translucent pink color and biocompatibility in terms of material characteristic. It keeps its flexibility for a long time after production, imposes a less burden on the teeth used as abutment, and it can be easily insert and remove due to its particular suppleness. Moreover, it is felt like real teeth more than metal-acrylic partial denture when being put in and takes alveolar bone under good protection since it receives occlusal force equally under the denture base. The most outstanding feature of Valplast is flexibility. The extent of its flexibility is determined by width & thickness of denture base. Considering general working procedure of Valplast, it can be seen that the thickness of denture base formed out of wax is increasing by the pressure while injecting resin. This research is to decide and test on the thickness increasing of Valplast by injecting pressure and the hypothesis upon that and is to prepare the basis estimating the increasing extent of thickness of denture base on the basis of the test result. In this test, it is expected occlusal malposition & thickness increasing of denture base by injecting pressure according to 4 kinds of test data which are to select 3 types of sprue method settling the forefront position at which the test material of fixed standard can be invested and to position the test material at the rearmost part keeping the minimum distance to set sprue. For 4 kinds of injecting test by investment position & sprue type, 20 test materials, 5 for each test were produced and a pressure of 1,180Kg was given with automatic injector of air cylinder type. The results are as follows: 1. For the amount of thickness increasing of denture base by investment position, the thickness of front investment is less increasing than the one of rear investment. 2. For the amount of thickness increasing of denture base by sprue type, the thickness of straight decompression sprue type which can absorb the injecting pressure after injecting polyamide base resin is less increasing than the other sprue types.

• Advances in aircraft and spacecraft science
• /
• 제7권3호
• /
• pp.203-214
• /
• 2020

In many applications like the aircraft or the rockets/missiles, the flow from a nozzle needs to be expanded suddenly in an enlarged duct of larger diameter. The enlarged duct is provided after the nozzle to maximize the thrust created by the flow from the nozzle. When the fluid is suddenly expanded in an enlarged duct, the base pressure is generally lower than the atmospheric pressure, which results in base drag. The objective of this research work is to optimize the length to diameter (L/D) ratio of the enlarged duct using the CFD analysis in the flow field from the supersonic nozzle. The flow from the nozzle drained in an enlarged duct, the thrust, and the base pressure are studied. The Mach numbers for the study were 1.5, 2.0 and 2.5. The nozzle pressure ratios (NPR) of the study were 2, 5 and 8. The L/D ratios of the study were 0.5, 1, 2, 3, 4, 5, 6, 7, 8, 9 and 10. Based on the results, it is concluded that the L/D ratio should be increased to an optimum value to reattach the flow to an enlarged duct and to increase the thrust. The supersonic suddenly expanded flow field is wave dominant, and the results cannot be generalized. The optimized L/D ratios for various combinations of flow and geometrical parameters are given in the conclusion section.

• 한국산학기술학회논문지
• /
• 제17권7호
• /
• pp.54-62
• /
• 2016

열을 전기로 바꾸는 장치로 가장 효율이 우수한 장치인 AMTEC은 알칼리금속을 작동유체로 하여 열을 직접적으로 전기로 변환시키는 장치이다. AMTEC은 저압용기, 고압용기, 베타 알루미나 고체 전해질, 그리고 순환윅으로 이루어져있다. AMTEC에서의 열손실은 주요하게 저압용기에서의 BASE와 응축부 사이에서 발생하는 열복사손실이며, 암텍의 발전량은 BASE의 온도유지력에 영향을 받기에 BASE의 표면온도를 고온으로 유지시켜주어야 고효율 발전량은 일정하게 유지할 수 있다. 이를 위하여 저압챔버에서의 복사 열손실을 줄이고 BASE온도는 상승시키고, AMTEC 시스템의 발전량 향상을 위하여 저압용기 내부의 6가지 형태의 열복사차단막에 따른 출력을 전산유체해석을 통하여 분석하였다. 분석에서 최적의 열복사차단막 형상은 수직부에 곡률을 가질 때이며, 그 때의 온도에 대한 무차원수(응축부온도/BASE온도 비)는 0.665 정도이고 출력은 약 17.69 W 정도로 다른 형상에 대비하여 높은 발전량을 갖는 것으로 계산되었다. 높이에 따른 발전량의 차이에서는 수평차단막이 BASE 상부로부터 멀리 떨어진 경우 발전량이 가장 우수하며, 17.58W 정도로 나타났다. 여러 개의 작은 홀과 다중 수평차단막을 설계한 경우는 기준이 되는 형상보다 오히려 발전량이 감소하였으며, 각각 0.91W, 2.06W 정도 감소하였다.

• 대한치과보철학회지
• /
• 제31권3호
• /
• pp.385-393
• /
• 1993

Injection processing of denture base resin was introduced by Pryer in 1942, in an attempt to reduce processing shrinkage. More recently a continuous-pressure injection type technique has been developed (SR-Ivocap, Ivoclar AG, Schaan, Liechtenstein.), and it reduced processing error and increased resin density. The purpose of this study was to compare tensile bond strength of heat-cured, cold-cured, and light-cured denture base resin bonded to continuous-pressure injection type resin. To know it, 60 cylindrical resin specimens were fabricated, and tensile bond strength were measured. The results were as follows : 1. The mean tensile bond strength bonded to continuous-pressure injection type resin was lower than bonded to conventional heat cured resin. But tensile bond strength of conventional heat cured resin bonding with light cured resin was lower than continuous-pressure injection type resin. 2. Of the tensile bond strength bonded to continuous-pressure injection type resin, tensile bond strength bonding with continuous-pressure injection type resin was the greatest(but not significantly different from bonding with conventional heat cured resin), followed by cold-cured, light-cured resin. 3. Of the tensile bond strength bonded to conventional heat cured resin, tensile bond strength bonding with conventional heat cured resin was the greatest and followed by continuous-pressure injection type resin, cold-cured resin, light-cured resin. According to these results, bonding of continuous-pressure injection type resin with conventional heat cured resin or continuous-pressure injection type resin is acceptable, but bonding with light-cured resin is questionable.

• 한국지반공학회논문집
• /
• 제32권10호
• /
• pp.41-53
• /
• 2016

토사층 하부에 절리암반층이 존재하는 복합지반을 굴착하고 설치하는 흙막이 구조물의 안정성은 배면에 작용하는 토압에 의해 결정된다. 보통 복합지반에서는 암반층을 토사로 간주하고 암반층의 지반강도 정수를 적용하여 경험적으로 토압을 구하는데, 암반층의 불연속면을 고려하지 않기 때문에 대개 실제 작용 토압보다 작게 산정된다. 본 연구에서는 복합지반에서 토사층과 암반층의 구성비율 및 암반층의 절리경사에 따라 흙막이 벽체에 작용하는 토압의 크기와 분포형태를 규명고자 대형토조(높이 3.0m, 길이 3.0m 폭 0.5m)에서 축척 1/14.5로 2차원 대형 모형실험을 수행하고, 같은 조건으로 수치해석을 수행하였다. 실험지반은 토사층과 암반층의 분포비가 각각 65%:35%와 50%:50%가 되도록 조성하였고, 암반층의 절리는 굴착측으로 $0^{\circ}$, $30^{\circ}$, $45^{\circ}$, $60^{\circ}$ 각도로 구성하였다. 그 결과 흙막이 벽체에 작용하는 토압은 암반층 절리 경사각(J)이 커질수록 증가 하였으며, 암반층비율이 증가함에 따라 암반층에 작용하는 토압도 증가하였다. 암반층에 작용하는 토압은 암반층의 비가 50%(R50)이고, 암반층의 절리 경사각이 $60^{\circ}$일 때 가장 크게 발생하였다. 대형모형실험과 수치해석 결과를 바탕으로 임의 복합지반을 굴착할 때 발생하는 토압을, 최상단 버팀대토압과 최대토압 및 굴착하단을 꼭짓점으로 하는 사각형분포로 이상화하고, 암반층비율과 절리경사각도를 고려하여 토압을 구할 수 있는 토압식을 제안하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.471-476
• /
• 2001

The main object of this study is to develop a reliable FEM simulation technique for stability test using ABAQUS software and to clarify the effect of base profile of a steel D&I(drawn and ironed) can on the dome reversal pressure. For the can after body making simulation, two kind of stability test, dome buckle test and axial crush test are performed. The factors studied in the base profile on the dome reversal pressure are the base diameter, the rim radius, the dome shoulder radius, the dome radius and the dome depth. Within the limits before the occurrence of normal snap-through buckling of dome, the dome reversal pressure is improved by decreasing the base diameter, increasing the dome depth or increasing the dome shoulder depth.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2010년 춘계학술대회논문집
• /
• pp.195-200
• /
• 2010

Numerical investigation was conducted to study the effects of after-body configurations and nozzle lip on the PIFS(Plume Induced Flow Separation) and eat flux to the base face. Two dimensional and axi-symmetric non-equilibrium Navier-Stoke's solver with $k-{\omega}$ SST turbulence model was used to solve the launching vehicle type configuration with propulsive jet. The experimental result of Robert J. McGhee was compared with our computational results for code validation. Three types of the after-body configurations (Straight, Boat-tail, Flare type) were simulated for this study. And the nozzle lip effect was studies using the three types of base configurations same simulation conditions. As a result of numerical investigations, higher pressure ratio condition and boat-tail after-body configuration caused severe PIFS phenomenon but the flare type after-body configuration and low pressure ratio suppressed PIFS. Flare type after-body configuration and low pressure ratio case reduced heat flux to base face. The nozzle lip dispersed the heat flux widely along the base face and the nozzle lip.