• Transactions of the Society of Information Storage Systems
• /
• v.9 no.2
• /
• pp.62-66
• /
• 2013

For the production method, stamp base is increasing the market share. But also, by the manufacturing method, stiffness of the stamp base is small. Many studies have been carried out in order to increase the stiffness of the stamp base. In this study, we optimally designed according to the position of bolting using a screening method in order to increase the stiffness base. After establishing a simulation model, the maximum deformation and frequency of the first mode based having relevance with stiffness of the base, were optimized. There for, it was possible to expect of increasing the stiffness of the stamp base.

• Journal of Industrial Technology
• /
• v.26 no.B
• /
• pp.29-34
• /
• 2006

A convective, radiating rectangular fin is analysed by using the one dimensional analytic method. Instead of constant fin base temperature, heat conduction from the inner wall to the fin base is considered as the fin base boundary condition. Radiation heat transfer is approximately linearized. For different fin tip length, temperature profile along the normalized fin position is shown. The fin tip length for 98% of the maximum heat loss with the variations of fin base length and radiation characteristic number is listed. The maximum heat loss is presented as a function of the fin base length, radiation characteristic number and Biot number.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.2
• /
• pp.28-33
• /
• 2008

In a scanning electron microscope (SEM), outside acoustic noise causes image noise that distorts observations of the specimen being examined. A SEM that is less sensitive to acoustic noise is highly desirable. This paper investigates the image noise problem by addressing the mode shapes of the base plate and the transmission path of the acoustic noise and vibration. By arranging the position of the rib, a new SEM base plate was developed that had twisting as the 1st and 2nd modes. In those two twisting modes, vibration nodes existed near the center of the base plate where the specimen chamber is placed. Less vibration was transmitted to the chamber and to the specimen by the twisting modes compared to bending ones, which are the 2nd and 3rd modes for a rectangular plain base plate. An SEM with the developed base plate installed exhibited a significant reduction of image noise when exposed to acoustic noises below 250 Hz.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.7
• /
• pp.1567-1572
• /
• 2009

Conformational change of ubiquitin variant with valine to alanine mutation at sequence position 26 was studied by varying solvent pH. Fluorescence emission spectra indicated that this variant ubiquitin has some residual structures in acidic and basic solution as compared to denaturant-induced unfolded state. Far-UV circular dichroic spectra indicated that the base-denatured state had more secondary structure than the acid-denatured state. Near-UV circular dichroic spectra indicated that the aromatic side-chains were in the relatively more rigid environment in the base-denatured state than those in the acid-denatured state. Although it appears that the more tertiary structure present in the base-denatured state, refolding reactions measured by stopped-flow fluorescence device suggest that both the acid- and base-denatured states occur before the major folding transition state. The acid- and base-denatured states are considered to reflect the early event of protein folding process.

• Journal of the Korean Society of Industry Convergence
• /
• v.22 no.3
• /
• pp.315-324
• /
• 2019

This paper present a novel 6-axis robotic base platform with force/moment sensing. The robotic base platform is made up of six loadcells connecting the moving plate to the fixed plate by spherical joints at the both ends of loadcells. The statics relation is derived, the robotic base platform prototype and the loadcell measurement system are developed. The force/moment calibrations in joint and Cartesian spaces are performed. The algorithm to detect external force applied at a working robot is derived, and using a 6-DOF robot mounted on the robotic base platform, force/moment measurement experiments have been performed.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.10
• /
• pp.45-52
• /
• 2001

This paper presents a study on the position tracking control of a robot system on the uncertain elastic base. The elastic bathe is a nonholonomic system but it can be changed into holonomic system, which is much easier to analyze, by modeling an elastic base as a virtual robot that has passive joints. Also, Jacobian operators, which represent the overall robot system including base movement, are defined and applied to the changed model. However, because base movements are not known, the exact Jacobian operators can＇t be estimated. The control algorithm proposed is that uses only Jacobians of a real robot as approximate Jacobian operators. Therefore the approximate Jacobian operators compensate the measured errors from external sensors. The proposed control strategy is evaluated by the simulation and experiment of a single-axis robot system on the elastic base.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.4
• /
• pp.739-744
• /
• 2005

For the structure of AVLS is required to the GPS-MDT for realtime acquisition the position reporting of vehicle and traffic management S/W. It is necessary that the MODEM using VHF transceiver base on GPS and monitoring program for display base on GIS the traffic status by vehicles position report in management system. The other wise, vehicles among management system that is required the automatic communications protocol for GPS information and mobile's ID. In his paper have studied the VHF modem for transmission the voice and data at same time and S/W for management system using GIS-tool.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.12
• /
• pp.115-125
• /
• 2003

The design methodology of plastic injection molding die has been gradually moved from two-dimensional line drawings to three-dimensional solid models. The 3D design gives many benefits, a few of which are: ease of design change, data associativity from concept design to final assembly. In the paper represented is the implementation of a program which automatically generates 3D mold-bases and cooling-lines, conforming to given geometric constraints. It utilized a commercial CAD software and the related API(application program interface) libraries. We constructed a DB(database) of typical mold-bases assembled from standard parts, from which the geometry (position & dimension) of a mold-base and composed parts can be automatical]y determined by a few key parameters. Also we classified cooling lines into several typical types and constructed a DB, from which the position of cooling lines is automatically determined. The research is expected not only to simplify construction of a 3D mold-base model including cooling lines but also to reduce design efforts, by way of databases and automatized determination of geometric dimensions.

• Journal of Welding and Joining
• /
• v.23 no.4
• /
• pp.73-80
• /
• 2005

Arc blow being occurred by Electro-Magnetic force(EMF) during the electric arc welding prevents the formation of a sound weldment. In this study, the effects of arc position, groove size, tack weld and base plate on the EMF in a butt-joint welding of mild steel plate are analyzed by a computer simulation based on the finite element method. The EMF can be numerically identified to be caused by a difference of the magnetic flux-density between ahead of and behind the arc in case that the workpiece locates asymmetrically around the uc. When there exists an air gap of groove ahead of the arc in the welding direction, the similar magnetic force has been producted regardless of the arc position and the gap size. The tack weld alleviates the magnetic force to about one fourth at the finish end of the workpiece. The magnetic force can be also significantly reduced with the base plate to about one fifth at the start end of the workpiece containing a tack weld.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.1
• /
• pp.256-260
• /
• 2005

For the structure of AVLS is required to the GPS-MDT for realtime acquisition the position reporting of vehicle and traffic management S/W. It is necessary that the MODEM using VHF transceiver base on GPS and monitoring program for display base on GIS the traffic status by vehicles position report in management system. The other wise, vehicles among management system that is required the automatic communications protocol for GPS information and mobile's ID. In this paper have studied the VHF modem for transmission the voice and data at same time and S/W for management system using GIS-tool.