• Transactions on Electrical and Electronic Materials
• /
• 제14권4호
• /
• pp.221-224
• /
• 2013

Effects of ambient temperature on the ac electrical treeing and breakdown behaviors in an epoxy/layered silicate (1 wt%) were carried out in needle-plate electrode geometry. A layered silicate was exfoliated in an epoxy base resin,, using our ac electric field apparatus. To measure the treeing initiation and propagation, and the breakdown rate, constant alternating current (ac) of 10 kV (60 Hz) was applied to the specimen in a needle-plate electrode arrangement, at $30^{\circ}C$, $90^{\circ}C$ or $130^{\circ}C$ of insulating oil bath. At $30^{\circ}C$, the treeing initiation time and the breakdown time in the epoxy/layered silicate (1 wt%) system were 1.4 times higher than those of the neat epoxy resin. At $90^{\circ}C$ (lower than Tg), electrical treeing was initiated in 55 min, and propagated until 1,390 min at the speed of $0.35{\times}10^{-3}mm/min$, which was 4.4 times higher than that at $30^{\circ}C$; however, there was almost no further treeing propagation after 1,390 min. At $130^{\circ}C$ (higher than Tg), electrical treeing was initiated in 44 min, and propagated until 2,000 min at the speed of $0.96{\times}10^{-3}mm/min$. Typical branch type electrical treeing was obtained from the neat epoxy and epoxy/layered silicate at $30^{\circ}C$, while bush type treeing was observed out from the needle tip at $90^{\circ}C$ and $130^{\circ}C$.

• Transactions on Electrical and Electronic Materials
• /
• 제14권6호
• /
• pp.308-311
• /
• 2013

The effect of an electric field on the ac electrical treeing in various epoxy/reactive diluent systems was studied in a needle-plate electrode geometry. Diglycidyl ether of bisphenol A (DGEBA) type epoxy was used as a base resin, and 1,4-butanediol diglycidyl ether (BDGE) or polyglycol (PG) as a reactive diluent was introduced to the DGEBA system, in order to decrease the viscosity of the DGEBA epoxy system. BDGE was acted as a chain extender, and PG acted as a flexibilizer, after the curing reaction. To measure the treeing initiation time and the propagation rate, three constant alternating currents (ac) of 10, 13 and 15 kV/4.2 mm (60 Hz) were applied to the specimen, in a needle-plate electrode arrangement, at $30^{\circ}C$ of insulating oil bath. When 10 kV/4.2 mm (60 Hz) was applied, the treeing initiation time and the propagation rate in the DGEBA system were 356 min and $1.10{\times}10^{-3}$ mm/min, respectively, those in the DGEBA/BDGE system were 150 min and $1.14{\times}10^{-3}$ mm/min, respectively. Those in the DGEBA/PG system were 469 min and $1.05{\times}10^{-3}$ mm/min, respectively. As 15 kV/4.2 mm (60 Hz) was applied, the propagation rate in the DGEBA system was $5.41{\times}10^{-3}$ mm/min, and that in the DGEBA/PG system was $1.42{\times}10^{-3}$ mm/min. These values meant that PG could be used as a reactive diluent in the DGEBA system, without the deterioration of the insulation breakdown property.

• 한국정밀공학회지
• /
• 제24권4호
• /
• pp.115-122
• /
• 2007

Recently, remarkable progress has been made in both technology and production of optical elements including aspheric lens. Especially, requirements for machining glass materials have been increasing in terms of limitation on using environment, flexibility of material selection and surface accuracy. In the past, precision optical glass lenses were produced through multiple processes such as grinding and polishing, but mass production of aspheric lenses requiring high accuracy and having complex profile was rather difficult. In such a background, the high-precision optical GMP process was developed with an eye to mass production of precision optical glass parts by molding press. This GMP process can produce with precision and good repeatability special form lenses such as camera, video camera, aspheric lens for laser pickup, $f-\theta$ lens for laser printer and prism, and me glass parts including diffraction grating and V-grooved base. GMP process consist a succession of heating, forming, and cooling stage. In this study, as a fundamental study to develop molds for GMP used in fabrication of glass lens, we conducted a glass lens forming simulation. In prior to, to determine flow characteristics and coefficient of friction, a compression test and a compression farming simulation for PBK40, which is a material of glass lens, were conducted. Finally, using flow stress functions and coefficient of friction, a glass lens forming simulation was conducted.

• Journal of Welding and Joining
• /
• 제32권1호
• /
• pp.15-21
• /
• 2014

FCAW(Flux Cored Arc Welding), SAW(Submerged Arc Welding), EGW(Electro Gas Welding), and three-pole SAW are applicable in manufacturing the offshore wind tower. In this paper, mechanical properties of these welded-joints for TMCP steels were evaluated in all above welding processes. The tensile strength of welded-joints for all the welding methods satisfied the standard guideline (KS D 3515). No cracking on weldment was found after the bending test. Changes of weldedments hardness with welding processes were observed. In a weld HAZ (heat-affected zone), a softened HAZ-zone was formed with high heat input welding processes (SAW and EGW). However, the welded-joint fractures were found in the base metal for all cases and small decrease in welded-joint strength was caused by a softened zone. The multi-pole SAW welds exhibited similar mechanical properties comparing to the one with one-pole SAW process.

• 대한족부족관절학회지
• /
• 제8권2호
• /
• pp.117-120
• /
• 2004

저자에 의해 개선된 변형 Mau 절골술은 우수한 교정력과 견고한 고정이 가능하면서도 술기가 간단하고 중족골두의 상하 전위가 없고 조기 보행이 가능한 안전한 방법이라 할 수 있었다. 따라서 향후 장기 추시가 필요하긴 하지만 중족골간각이 큰 중증의 무지외반증에서 추천할만한 좋은 방법으로 사료된다.

• 한국레이저가공학회지
• /
• 제10권3호
• /
• pp.25-32
• /
• 2007

The effect of welding speed on the weldability, microstructures, hardness, tensile property of Nd:YAG laser welding joint in 600MPa grade precipitation hardening high strength steel was investigated. A shielding gas was not used, and bead-on-plate welding was performed using various welding speeds at a power of 3.5kW. Porosity in the joints occurred at 1.8m/min, but were not observed over the welding speed of 2.1m/min. However, spatter occurred over the welding speed of 6.6m/min. The hardness was the highest at heat affected zone(HAZ) near fusion zone(FZ), and was decreased on approaching to the base metal. The maximum hardness increased with increasing welding speed. The microstructure of FZ was composed of coarse grain boundary ferrite and bainite(upper) but the HAZ near the FZ contained bainite(Lower) and fine ferrite at a low welding speed. With increasing welding speed, ferrite at the FZ and the HAZ became finely and upper binite changed to lower bainite. In a perpendicular tensile test to the weld line, all specimens were fractured at the base metal, and the tensile strength and the yield strength of joints was equal to those of raw material. Elongation was found to be lower than that of the raw material.

• 자원환경지질
• /
• 제29권6호
• /
• pp.665-676
• /
• 1996

안정적인 천연자원의 공급을 통해 오랫동안 국가산업화에 이바지해온 일본의 광산산업은 산업구조의 개편에 따라 하향추세를 맞아 현재는 세 곳의 주요 광산만이 가행중이다. 최근 경제사정의 변화로 새로운 비금속광상의 개발이 어려워짐에 따라 매장량과 품위에 있어 경제적 가치를 갖는 천열수금광상으로 관심이 옮겨가고 있는 추세이다. 1970년대 후반의 급격한 금가격 상승은 환태평양 지역의 천열수금광상에 대한 지질학적 정보와 이해를 증가시키는 역할을 했으며, 특히 판구조론의 확립과 더불어 지열수계와 화석천열수계의 대비라는 가장 중요한 발전이 이루어졌다. 1988년에는 광산협회에서 천열수금광상의 개발을 목표로 일본내 19개 지역의 탐사를 인가했으며, 1989년부터는 준정부기관인 금속광업국에서 이 지역들의 금탐사를 수행해왔다. 광상성인에 관한 신개념과 새로운 탐사기술로 유망한 금광화대가 발견되어 왔으며 개발이 진척된 곳은 홋카이도 북부의 세타지역과 큐슈 중부의 노야지역이다.

• Imaging Science in Dentistry
• /
• 제51권1호
• /
• pp.81-86
• /
• 2021

Purpose: This study was performed to assess and describe the imaging features of 40 cases of Stafne bone defects (SBDs) on computed tomographic (CT) examinations. Materials and Methods: This study collected data, including age and sex, from 40 patients with SBDs who underwent CT exams. The imaging features of the SBDs were assessed in terms of their location, average size, the relationship of their contour with the cortical plate of the lingual mandible, bone margins, degree of internal density, shape, topographic relationship between the defect and the mandibular edge, the distance from the SBD to the base of the mandible, and the Ariji classification (type I, II, and III). Results: The average age was 57.3 years(range, 28-78 years), and the patients were predominantly male (70%). In all cases (100%), the posterior unilateral lingual SBD variant was observed. Within the Ariji classification, type I was the most common (60%). Among the most frequently observed radiographic characteristics were thick sclerotic bone margin across the entire defect contour, completely hypointense internal content, an oval shape, and continuity with the mandibular base with discontinuity of the mandibular edge. Conclusion: This study showed that posterior SBDs could present with an oval or rounded shape, complete hypodensity, and thick sclerotic margins. Likewise, SBDs could appear almost anywhere, with minor differences from the classic SBD appearance. It is fundamental for dental practitioners to know the imaging features of SBDs, since they are diagnosed primarily based on imaging.

• 한국건축시공학회지
• /
• 제23권1호
• /
• pp.1-9
• /
• 2023

본 연구에서는 보편적으로 건물의 옥상 등에 사용되는 폴리 우레탄 방수재의 바탕구조물의 함수정도와 시공환경조건에 따른 하자원인을 분석하기 위한 것으로 바탕판의 함수조건에 따른 부착강도, 표면상태를 육안관찰하였고, 온도, 습도의 양생조건에 따라서 방수재 도막의 기계적 성능을 평가하였다. 실험결과 바탕판의 함수상태가 10%이상일 때 도막의 부착이 이뤄지지 않음을 확인하였고, 온습도 조건이 20℃, 80% RH일때는 기초물성이 모두 확보되었으나, 40℃, 60% RH일 때 표면에 기포가 관찰되었으며, 40℃, 80% RH일 때 건조도막 기초물성이 KS F 3211 성능기준이하로, 우레탄 방수재 도포에 있어 시공환경조건의 하자원인 중 바탕판의 함수조건 및 양생 시 절대습도가 중요한 요인임을 확인하였다.

• Clinics in Shoulder and Elbow
• /
• 제11권2호
• /
• pp.177-184
• /
• 2008

목적: 금속판을 이용하여 치료한 8예의 구상돌기 골절의 치료 결과를 분석하여 보고하고자 한다. 대상 및 방법: 금속판을 이용하여 고정한 8예의 구상돌기 골절에 대하여 후향적 연구를 시행하였다. 남자가 6예, 여자가 2예였고, 평균 나이는 41세였다. Regan의 골절 분류에 의하면 제2형이 5예, 제3형이 3예였으며, O'Driscoll의 분류에 의하면 전내측형이 5예, 기저형이 3예였다. 전 예에서 척 수근 굴근 분리를 통한 내측 도달법을 이용하였으며, 골편 정복 후 금속판으로 골편을 지지 고정하였다. 추시 기간은 평균 15.8개월이었으며, Mayo Elbow Performance Score로 임상적 결과를 판정하였다. 결과: 능동적 주관절 가동 범위는 평균 120도였고, Mayo Elbow Performance Score는 평균 86.9점으로 5예에서 최우수, 1예에서 우수, 2예에서 양호의 결과를 보였다. 요약: 불안정한 주관절이 동반된 전위된 구상돌기 골절들을 내측 접근법을 통한 금속판 고정으로 안정된 고정과 만족스러운 골유합을 얻을 수 있었다.