• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.167-174
• /
• 2001

Reflection method using ultrasonic source has been attempted to obtain the information about tunnel lining structures composed of lining, shotcrete, water barrier and voids at the back of lining. In this work, two different types of sources, i.e. single-pulse source and sweep source, can be used. Single-pulse source with short time duration has the frequency content whose amplitudes tend to be concentrated around the dominant frequency, whereas sweep source with long time duration denotes a flat distribution of relatively larger amplitude over a broad frequency band, although the peak to peak amplitude of single-pulse source wavelet is equivalent to that of sweep source one. In traditional seismic application, a single-pulse source(weight drop, dynamite) is typically used. However, to investigate the fine structure, as it is the case in the tunnel lining structure, the sweep wavelet can be also a desirable source waveform primarily due to the higher energy over a broad frequency band. For the investigation purposes of sweep source, a physical modeling is a useful tool, especially to study problems of wave propagation in the fine layered media. The main purpose of this work was using a physical modeling technique to explore the applicability of sweep source to the delineation of inner layer boundaries. To this end, a two-dimensional physical model analogous to the lining structure was built and a special ultrasonic sweep source was devised. The measurements were carried out in the sweep frequency range 10 ∼ 60 KHz, as peformed in the regular reflection survey(e.g. roll-along technique). The measured data were further rearranged with a proper software (cross-correlation). The resulting seismograms(raw data) showed quitely similar features to those from a single-pulse source, in which high frequency content of reflection events could be considerably emphasized, as expected. The data were further processed by using a regular data processing system "FOCUS" and the results(stack section) were well associated with the known model structure. In this context, it is worthy to note that in view of measuring condition the sweep source would be applied to benefit the penetration of high frequency energy into the media and to enhance the resolution of reflection events.

• Geophysics and Geophysical Exploration
• /
• v.26 no.2
• /
• pp.52-61
• /
• 2023

The use of ultra-high-resolution (UHR) seismic surveys to preceisly characterize coastal and shallow structures have increased recently. UHR surveys derive a spatial resolution of 3.125 m using a high-frequency source (80 Hz to 1 kHz). A digital streamer system is an essential module for acquiring high-quality UHR seismic data. Localization studies have focused on reducing purchase costs and decreasing maintenance periods. Basic performance verification and application tests of the developed streamer have been successfully carried out; however, a comparative analysis with the existing benchmark model was not conducted. In this study, we characterized data obtained by using a developed streamer and a benchmark model simultaneously. Tamhae 2 and auxiliary equipment of the Korea Institute of Geoscience and Mineral Resources were used to acquire 2D seismic data, which were analyzed from different perspectives. The data obtained using the developed streamer differed in sensitivity from that obtained using benchmark model by frequency band.However, both type of data had a very high level of similarity in the range corresponding to the central frequency band of the seismic source. However, in the low frequency band below 60 Hz, data obtained using the developed streamer showed a lower signal-to-noise ratio than that obtained using the benchmark model.This lower ratio can hinder the quality in data acquisition using low-frequency sound sources such as cluster air guns. Three causes for this difference were, and streamers developed in future will attempt to reflect on these improvements.

• Korean Journal of Materials Research
• /
• v.4 no.6
• /
• pp.723-729
• /
• 1994

We have investigated on the photoreflectance(PR) of heavily Si-doped n-GaAs. The PR response was found to be dependent of modulation beam intensity, modulation frequency, and temperature. From the observed Franz-Keldysh oscillation(FKO), we determined the band gap energy and surface electric field. As the temperature is decreased from room temperature to 77K, the band gap energy increases while the surface electric field decreases. The quality of crystal was greatly increased after thermal annealing for 5 min at $500^{\circ}C$.

• Phonetics and Speech Sciences
• /
• v.4 no.2
• /
• pp.89-94
• /
• 2012

The aim of this study is to investigate the usefulness of the parameter CPP (cepstral peak prominence) and LTAS (long term average spectrum) band energy for an analysis of breathy voice with vocal fold paralysis. Thirty-four female subjects who have vocal paralysis after thyroidectomy participated in this study. According to the perceptual judgements by three speech pathologists and one phonetic scholar, subjects were divided into two groups: breathy voice group (n = 21) and non-breathy voice group (n = 13). Maximum sustained phonation task was measured for acoustic analysis. CPP-related (i.e. mean F0, mean CPP, and mean CPPs) and LTAS-related (i.e. minimum, maximum, and mean) parameters were used. Independent samples t-test was conducted. Regarding CPP, there are significant differences in mean CPP and mean CPPs between groups. The values of mean CPP and CPPs in the non-breathy voice group are higher than those in the breathy voice group. The CPP could be regarded as the useful parameter for breathy voice analysis in the clinic. When it comes to LTAS, energy from 0 to 2 kHz are significantly different between groups. The minimum value of non-breathy group is lower than that of breathy group, whereas the maximum value of non-breathy group is higher. The frequency band below 2 kHz seems to be related to breathy voice.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.2
• /
• pp.121-125
• /
• 2013

It is an analysis about electromagnetic wave which is generated from a Spark plug cable of Distributorless spark ignition system. In case of Distributorless spark ignition system, high frequency generation is an ignition coil and Spark plug cable and Spark plug could be activated with electromagnetic wave radiation antenna. I calculated a resonant frequency with HFSS by measuring length of Spark plug cable and Spark plug. The antenna was considered as ${\lambda}/4$ monopole antenna in this calculation. According to power spectrum measurement analysis of engine room radiated electromagnetic wave and calculated Resonant frequency, it is possible to find out that the Distributorless spark ignition system radiates high frequency energy in certain frequency band.

• Journal of the Korean Society of Industry Convergence
• /
• v.24 no.3
• /
• pp.295-300
• /
• 2021

This study investigated the dominant frequency of the elastic waves from the tensile test. The specimen was rolled with five different rolling degrees (10, 22, 33, 42 and 50%), which was treated subzero. The specimen was rolled at room temperature, which was transformed from austenite to martensite (only α'-martensite). The dominant frequency increased with an increase in the rolling degree regardless of the subzero temperature, and decreased after 33% of the rolling degree. On the other hand, higher frequency band was obtained at lower temperature and long time. The dominant frequency increased when the amount of α'-martensite increased and decreased with the α'-martensite amount between 50-65%. The lower subzero treatment temperature increased the amount of α'-martensite, which resulted in the higher dominant frequency. The longer treatment time at the same subzero temperature led to an increase in the amount of α'-martensite, leading to high dominant frequency.

• The Journal of the Acoustical Society of Korea
• /
• v.43 no.1
• /
• pp.112-121
• /
• 2024

The pipping system is widely used in many industries as equipment for transporting fluids over long distances. In high-pressure pipe, as the speed of the fluid increases, a loud noise is generated. Therefore, various studies have been conducted to reduce pipe noise. In this paper, a pipe noise analysis was developed to predict and quantitatively assess the flow-induced vibration and acoustic-induced vibration due to valve flow in high-temperature and high-pressure. To do this, a high-fidelity fluid analysis technique was developed for predicting internal flow in the pipe with valve. In additional, the contribution of compressible/incompressible pressure by frequency band was evaluated using the wavenumber-frequency analysis. To predict a low/middle frequency pipe noise, the vibroacoustic analysis method was developed based on Finite Element Method (FEM). And the pipe noise prediction method for the middle/high frequency was developed based on Statistical Energy Analysis (SEA).

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.11 no.2
• /
• pp.83-91
• /
• 2012

An RF energy detector for spectrum sensing in TV white space transceiver is presented. It is based on an RF active filtering technique that comprises a low-noise amplifier with a frequency-translation high-pass filtering feedfoward loop, which attenuates the unwanted sideband energy and only passes the wanted band energy. Unlike the conventional architecture, a new architecture that can attenuate both sidebands at the same time is proposed. A simplified system modeling method is presented to assess the non-ideality effects on the RF energy detector performances. System behavioral simulations demonstrate that the proposed architecture can be instrumental for realizaing a RF energy detector circuit in CMOS.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.4
• /
• pp.323-335
• /
• 1992

In this paper, an adaptive cosine transform coding scheme which incorporate human visual properties into the coding scheme is investigated. Human vision is relatively sensitive to mid-frequency band, and insensitive to very low and very high frequency band. These property was mathematically modelled with MTF(Modulation Transfer Function) through many psychovisual experiment. DCT transforms energy in spatial domain into frequency domain, so can exploit the MTF very efficiently. Another well-known visual characteristics is spatial masking effect that visibility of noise is less in regions of high activity than in regions of low activity. Proposed coding scheme imploys quantization matrix which represent the properties of these spatial frequency response of human vision, and adaptively quality of an image. To compute the activity index of an image block, simple operation is performed in spatial domain, and according to activity index. block of low activity region is more exactly quantized relatively than that of high activity region. Results showed that, at low bit rate, the subjective quality of the reconstructed images by proposed coding scheme is acceptible than that of coding scheme without HVS properties.

• Journal of the Korean GEO-environmental Society
• /
• v.10 no.1
• /
• pp.35-41
• /
• 2009

It is necessary to consider the site amplification for estimating SSI (soil structure interaction) and seismic source with more confidence. The horizontal to vertical (H/V) ratio technique in spectral domain is one of several techniques to estimate empirical site transfer function. The technique, originally proposed by Nakamura (1989), is applied to analyze the surface waves in the microtremor records. However, the application of this technique has been widened to the shear wave energy of strong motions for estimating site amplification. The purpose of this paper is to estimate spectral ratio using observed data at the seismic stations distributed within Southern Korean Peninsula from the Fukuoka earthquake including 11 aftershocks. The results show that each station has the its own characteristics of the specific resonance, high-band, and low-band frequency. The characteristics of the resonance frequency is more important because the quality of the seismic records are dependent on the resonance frequency. The result can be used for the study of site classification and removal of the site amplification effects from observed records can give us more reliable seismic source parameters.