• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.245-251
• /
• 2004

This paper is studied on the effect of TiAlN coated Ball End Mill and MQL(Minimum Quantity Lubrication) cutting condition on cutting characteristic of high hardness steels. KP4 steels[HRC32] and STD11[HRC60] heat treated steels were used as the workpiece and WC-Co ball end mill and single and multi layer TiAlN coated ball end mill were utilized in the cutting tests. MQL device was used to spray botanical oil coolant. Result showed that TiAlN coated ball end mill were increased the cutting length than WC-Co ball end mill in the cutting speed[$245{\sim}320m/min$] about $2.3{\sim}5.7$ times for KP4 steels and about $2.5{\sim}4.3$ times far STD11 heat treated steels. The multi layer TiAlN coated ball end mill is good for KP4 steels than single layer coated.

• Tribology and Lubricants
• /
• v.13 no.4
• /
• pp.47-52
• /
• 1997

Friction torques, electrical contact resistances and bearing temperatures were measured on high speed angular contact ball beatings for the spindle of machine tools. The test bearings ran with oil-air lubrication at the thrust loads from 320 N to 1920 N and at the rotational speed of up to 12000 rpm. Electrical contact resistances between balls and races were measured to evaluate the formation of the lubricant film in the contact area. The test results with sufficient lubrication showed that the variations of friction torques were sensitive to the thrust loads and the rotational speeds, and that the friction torques were higher than those with insufficient lubrication. With insufficient lubrication and high thrust loads, the collapse of the lubricant film was detected even at a high rotational speed. It was concluded that these high speed beatings to run in condition of fluid lubrication should require monitoring not only the temperature increase of the bearing but also the lubricant film formation in contact areas resulting from the change in the applied load and the lubricant amount.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.9
• /
• pp.135-144
• /
• 1998

High speed machining is a key issue in die and mold manufacturing recently. Even though this technology has great potential of high productivity. tool wear accelerated by high cutting speed to the hardened materials is other barrier. In this research, we attempted to reduce tool wear by considering tool inclination angle between tool and workpiece. The boundary lines describing machined sculptured surfaces were represented by both of cutting envelop condition and the geometric relationship of successive tool paths. Chip cross section, and cutting length could be obtained from the calculated cutting edge and the rotational engagement angle. From the simulation results, machining inclination angle of tool of $15^\circ$ was good enough from the point of tool wear and cutting force, and this value was verified through the cutting experiment of high speed ball end milling.

• Journal of the Korean Ceramic Society
• /
• v.55 no.3
• /
• pp.275-284
• /
• 2018

In the ball milling process of ceramic powders, according to economic considerations for industrial applications, it is very important to quickly determine the optimum process condition with the maximum grinding efficiency. However, it is still difficult to determine the optimum condition for a ball mill with respect to the various process parameters, such as the rotational speed and the milling time. Ball milling was carried out at the same starting conditions with given amounts of alumina powders, balls and water, and was conducted slower or faster or a critical rotational speed was just determined by observing the angular position of the slurry in a semi-translucent polyethylene laboratory container. With respect to the different rotational speeds, which were slower or faster than the critical rotational speed, the particle size distribution of the grained powders and the acoustic intensity caused by cascading of the balls led to various behaviors. From the results of the particle size distribution and the acoustic signal analysis in the ball milling, there was one rotational speed that made the finest milled powder with maximum acoustic intensity. As a result, there was a correlation between the ground particle size and the acoustic intensity, which yields the interpretation that it can be possible in-situ to determine the optimum condition of ball milling by acoustic signal without repeated measurement efforts.

• Tribology and Lubricants
• /
• v.13 no.1
• /
• pp.70-75
• /
• 1997

The lubrication characteristics of high-speed ball bearings at oil-starvation have been investigated empirically using the bearings employed in small industrial gas turbine engines. For the close structural simulation, experiments carried our with bearing mounting supports of real engines, such as bearing housings and oil nozzle assemblies with squeeze film dampers. Thus the results of tests can be applied to the design and the development of gas turbine engines. Testing was done by simulating the oil-starvation conditions in engines, such as stopping the oil-supply to the bearing during normal operating, starting without oil-supply at atmospheric temperature, and accelerating with oil-supply at atmospheric temperature. From this study, the relative comparison of the frictional resistance and the resistance due to the bearing cavity oil was demonstrated visually, and the resistance due to the bearing cavity oil was dominant in the resistance of bearing at high speed.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.238-244
• /
• 2004

This research conducted milling tests to study effects of cutting environment conditions of ball end milts on the characteristics of high speed milling cutting process. KP4 steels and STD11 heat treated steels were used as the workpiece and WC-Co ball end mill tools with TiAIN coated were utilized in the cutting tests. Dry cutting without coolant and semidry cutting using botanical oil coolant by the MQL(Minimum Quantity Lubricant) device were conducted. Cutting forces, tool wear and surface roughness were measured in the cutting tests. Results showed that MQL spray cutting of KP4 and hardened STD11 specimens produced better surface quality and wear performance than dry cutting did.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.1
• /
• pp.273-283
• /
• 2018

The purpose of this study is to analyze the optimum driver selection according to shaft intensity, shaft length and shaft weight that are determining factors of driver shot. To achieve the above purpose, the subject were participate with handicap zero 10 male pro golfer and mean score 90(handicap about 18) amateur 10 male golfer. The used club limited number 1 driver, we tested 24 driver which is shaft intensity, length, weight, total weight and swing weight. Dependent variable was strike ball speed, flying distance and head speed. The findings can be summarized as follows. First, There is a significantly difference in CPM. Ball speed, head speed and flying distance according to driver shaft intensity were found to be the best when CPM is 230<. Second, There is a significantly difference in shaft length. Ball speed, and head speed according to driver shaft length were found to be the best at 46 inch and flying distance were found to be the best at 45 inch. Third, There is not significantly difference in SW. Ball speed and flying distance according to driver shaft weight were found to be the best with 65g. In the case of head speed, it was the fastest with 50g shaft. Four, total variables were significantly difference between in pro and amateur golfer. In conclusion, there would be differences in individual physical condition but the best result was found with a driver of CPM 230<, shaft length 46inch, and shaft weight 65g.

• International Journal of Precision Engineering and Manufacturing
• /
• v.7 no.3
• /
• pp.3-7
• /
• 2006

For the purpose to improve and to automate designing of high-speed spindle units (SU's), we have developed the mathematical models and software to estimate SU performance characteristics, including the run-out of spindles running on ball bearings. In order to understand better the mechanics of high-speed SUs, the dynamic interaction of ball bearings and SU, and the influence of the bearing imperfections and SU's operational conditions on the run-out, we have carried out computer simulation and experimental studies. Through the study of SU's, we have found out that run-out of SU can vary drastically with variation of rpm. The influences of rotation speed and of accuracy parameters of bearings on the SU accuracy have the greatest importance. The influence of bearing preload has a secondary importance. Comparison of the results of these studies has demonstrated adequacy of the models and software developed to the real SU's.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.8
• /
• pp.854-863
• /
• 2013

High-speed spindle systems typically employ angular contact ball bearings, which can resist both axial and radial loading, and exhibit high precision and durability. We investigated the effects of the arrangement of the angular contact ball bearings on the dynamics of high-speed spindle systems. The spindle dynamics were studied with a number of spindle-bearing models, and the location of the bearings was varied, along with the rotational speed and the preload. A finite element spindle model and a bearing model were used, and simulated data showed that the bearing arrangement significantly affected the spindle dynamics. Furthermore, the main effects were due to the cross coupling terms between the transverse and rotational motions of the ball bearings. The coupling stiffness terms were found to influence the spindle dynamics, depending on the mode shapes. An extensive discussion is provided on the effects of the bearing arrangement on the dynamics of the spindle.

• Korean Chemical Engineering Research
• /
• v.56 no.2
• /
• pp.191-203
• /
• 2018

This study was investigated the effect of the morphology change of copper (Cu) powders under the different rotational speed and milling time by using three kinds of grinding media with different size and materials, and performed DEM simulations of ball behavior. In order to clarify the mechanism of grinding by three - dimensional simulations of the ball behavior in a traditional ball mill, the force, kinetic energy, and medium velocity of the grinding media were calculated. In the simulation, the amount of change of the input energy was also calculated by adjusting the rotational speed, ball material, kinetic velocity, and friction coefficient in the same as the actual experimental conditions. The scanning electron microscope results show that the particle morphology changes from irregular to spherical when the ball size is small.