• Journal of Institute of Control, Robotics and Systems
• /
• v.22 no.11
• /
• pp.925-931
• /
• 2016

The BLDC motor is used widely in industry due to its controllability and freedom from maintenance because there is no mechanical brush in the BLDC motor. Furthermore, it is suitable for high-speed applications, such as compressors and air blowers. For instance, for a compressor with a small impeller due to miniaturizing, the BLDC motor has to rotate at a very high speed to maintain the compression ratio of the compressor. Typically, to reach an ultra-high speed, airfoil bearings must be used in place of ball bearings because of their friction. Unfortunately, the characteristics of airfoil bearings change drastically depending on the revolution speed. In this paper, a BLDC motor with airfoil bearings is controlled with a PID controller. To analyze and determine the PID coefficients, the relay-feedback method is used. Additionally, for adaptive control, a fuzzy logic controller is used. Furthermore, the auto-tuning and self-tuning techniques are combined to control the BLDC motor. The proposed method is able to control the airfoil-bearing BLDC motor efficiently.

• Physical Therapy Rehabilitation Science
• /
• v.6 no.4
• /
• pp.189-195
• /
• 2017

Objective: The purpose of this study was to examine the effects of real-time visual feedback weight shift training during golf swinging on golf performance. Design: Repeated-measures crossover design. Methods: Twenty-sixth amateur golfers were enrolled and randomly divided into two groups: The golf swing training with real-time feedback on weight shift (experimental group) swing training on the Wii balance board (WBB) by viewing the center of pressure (COP) trajectory on the WBB. All participants were assigned to the experimental group and the control group. The general golf swing training group (control group) performed on the ground. The golf performance was measured using a high-speed 3-dimensional camera sensor which analyses the shot distance, ball velocity, vertical launch angle, horizontal launch angle, back spin velocity and side spin velocity. The COP trajectory was assessed during 10 practice sessions and the mean was used. The golf performance measurement was repeated three times and its mean value was used. The assessment and training were performed at 24-hour intervals. Results: After training sessions, the change in shot distance, ball velocity, and horizontal launch angle pre- and post-training were significantly different when using the driver and iron clubs in the experimental group (p<0.05). The interaction time${\times}$group and time${\times}$club were not significant for all variables. Conclusions: In this study, real-time feedback training using real-time feedback on weight shifting improves golf shot distance and accuracy, which will be effective in increasing golf performance. In addition, it can be used as an index for golf player ability.

• Journal of Welding and Joining
• /
• v.33 no.3
• /
• pp.19-24
• /
• 2015

Joint properties of electric control unit (ECU) module using Sn-Cu-(X)Al(Si) lead-free solder alloy were investigated for automotive electronics module. In this study, Sn-0.5Cu-0.01Al(Si) and Sn-0.5Cu-0.03Al(Si) (wt.%) lead-free alloys were fabricated as bar type by doped various weight percentages (0.01 and 0.03 wt.%) of Al(Si) alloy to Sn-0.5Cu. After fabrications of lead-free alloys, the ball-type solder alloys with a diameter of 450 um were made by rolling and punching. The melting temperatures of 0.01Al(Si) and 0.03Al(Si) were 230.2 and $230.8^{\circ}C$, respectively. To evaluation of properties of solder joint, test printed circuit board (PCB) finished with organic solderability perseveration (OSP) on Cu pad. The ball-type solders were attached to test PCB with flux and reflowed for formation of solder joint. The maximum temperature of reflow was $260^{\circ}C$ for 50s above melting temperature. And then, we measured spreadability and shear strength of two Al(Si) solder materials compared to Sn-0.7Cu solder material used in industry. And also, microstructures in solder and intermetallic compounds (IMCs) were observed. Moreover, thickness and grain size of $Cu_6Sn_5$ IMC were measured and then compared with Sn-0.7Cu. With increasing the amounts of Al(Si), the $Cu_6Sn_5$ thickness was decreased. These results show the addition of Al(Si) could suppress IMC growth and improve the reliability of solder joint.

• Physical Therapy Korea
• /
• v.24 no.1
• /
• pp.71-78
• /
• 2017

Background: Muscle weakness and impaired trunk muscle control are common in stroke patients. The bridging exercise (BE) is generally used for trunk stabilization and improving the overall function of stroke patients. The effectiveness of the BE with hip adductor contraction (BEHA) in facilitating trunk muscle activation has been well studied in healthy adults. However, the impact of BEHA in sub-acute stroke patients has not yet been investigated. Objects: The purpose of this study was to determine the effects of BEHA on the electromyography (EMG) activities and the asymmetry of the rectus abdominis (RA), external oblique (EO) and internal oblique (IO) abdominal muscles. Methods: Twenty participants with sub-acute stroke (11 males and 9 females) were recruited. Each participant was asked to perform bridging exercises for five seconds under three different conditions: BE in a neutral position (BEN), BEHA with a large ball (BEHAL) and BEHA with a small ball (BEHAS). The EMG amplitudes of the bilateral RA, EO and IO and the asymmetry of the EMG activity between the sound and affected sides were compared among the conditions. The significance level was set at ${\alpha}=.05$. Results: The EMG activities of RA, EO and IO were significantly greater during BEHAL and BEHAS than during BEN (p<.05); the asymmetry of the RA, EO and IO decreased significantly during BEHAL and BEHAS compared to BEN (p<.05). However, no measured variables showed any significant differences between BEHAL and BEHAS (p>.05). Conclusion: This study compared the EMG activities of the RA, EO and IO on both sides and the asymmetry of the RA, EO and IO during BEN, BEHAL and BEHAS. Our findings suggest that BEHA was more effective for individuals with hemiplegic stroke at facilitating and normalizing abdominal muscle control than BEN.

• The Journal of Korean Academy of Prosthodontics
• /
• v.31 no.3
• /
• pp.394-410
• /
• 1993

This study was accomplished for appreciation of the mandibular moments according to antero- posterior movement of pivot placed on the lower natural dentition. For this study, 20 subjects(male, $21\sim30$ yrs., average age 24) in the category of normal occlusion were selected, and the intraoral Vitallium clutches were cast and fabricated for each subjects. A 2-dimension PSD(Position Sensitive Detector, Hamamatsu Photonics Co., Japan) was attached to maxillary clutch in a mode of three dimensional control and LED (Light Emit Diode, Hamamatsu Photonics Co., Japan) was set up on mandibular clutch. Both clutches were set into oral cavity of each subjects and adjusted. Then the subjects were allowed to intercuspated with maximal bite force while the pivoting ball in the mid-line moving from anterior toward posterior position. The displacement scales were recorded by CCD camera(Sony, CCD-TR-705) and VCR, The conclusions were as follows : 1. When the subject was allowed to bite the metal pivoting ball in the midline of lower dentition with maximal bite force voluntarily while moving from lower central incisor to canine, 1st premolar, End premolar, 1st molar and 2nd molar. The lever actions on the pivot were revealed in all subjects. The equilibrium of moment were revealed on the pivots of 1st premolar(14 subjects), End premolar(4 subjects), and canine(2 subjects) areas. 2. The changes of loading on the TMJ according to antero-posterior positional changes of metal pivoting ball were able to recognize as follow. Compression on the TMJ was increased when the pivot moves anteriorly from the equilibrium point, and tension on the TMJ was increased when posteriorly. 3. 13 subjects were recognized their habitual chewing sides(Rights, Left8), and 7 subjects were not. During maximal biting, mandible was displaced toward their habitual chewing sides on the metal pivoting ball in the frontal plane. 4. In cephalometric analysis, the average genial angle of 20 subjects was $116.75^{\circ}$ and the average mandibular body length was 79.77mm. The equilibrium points of mandibular moment were positioned more posteriorly in the subjects having larger Genial angle than in the smaller(p<0.05). Relationships among the angle between FH plane and occlusal plane, the angle between occlusal plane and mandibular plane , and mandibular body length were not significant(p>0.05).

• Korean Journal of Breeding Science
• /
• v.42 no.3
• /
• pp.276-279
• /
• 2010

A new standard rose cultivar 'Snow Ball' was bred by the cross between the red standard cultivar 'Red Sandra' and the scarlet standard cultivar 'Baroness' at the National Institute of Horticultural and Herbal Science, in Suwon. The cross was made in 1998 and 'Snow Ball' was finally selected in 2003 after investigating the characteristics for three years from 2001 to 2003. 'Snow Ball', a white standard cultivar grows vigorously and has good flower shape. The major characteristics of this cultivar are $90.3stems/m^2/year$ in yield, 57.8 cm in length of cut flower, 6.1 cm in flower diameter, 85.7 in petal number, and 15.0 days in vase life. This cultivar can be propagated by both cutting and grafting. The consumer's preference of this cultivar is relatively higher than that of control cultivar, 'Tineke'.

• Journal of Institute of Control, Robotics and Systems
• /
• v.11 no.7
• /
• pp.609-614
• /
• 2005

Parallel manipulators have been used for a variety of applications, including the motion simulators and mechanism for precise machining. Since the ball screws used for linear motion of legs of the Stewart-Gough type parallel manipulator provide wider contact areas than revolute joints, parallel manipulators are usually more affected by frictional forces than serial manipulators. In this research, the method for detecting the frictional forces arising in the parallel manipulator using the gravitational force is proposed. First, the reference trajectories are computed from the dynamic model of the parallel manipulator assuming that it is subject to only the gravitational force without friction. When the parallel manipulator is controlled so that the platform follows the computed reference trajectory, this control force for each leg is equal to the friction force arising in each leg. It is shown that control performance can be improved when the friction compensation based on this information is added to the controller for position control of the moving plate of a parallel manipulator.

• Tribology and Lubricants
• /
• v.19 no.1
• /
• pp.21-25
• /
• 2003

The 440C stainless steel is used for ball bearings and bevel gears in the control rod drive mechanism for the integral reactor, SMART. The friction characteristics of 400C stainless steel a investigated in sliding motion using the reciprocating tribometer which can simulate the operating conditions of the control rod drive mechanism. Highly purified water is used as lubricant, and the water is heated and pressurized in the autoclave. Friction force on the reciprocating specimens is measured by the load cells and transformed into friction coefficient. It is verified that frictional characteristic of the 440c steel is not drastically changed up to operating temperature and variation of friction coeffcient at operating temperature from room temperature to 160$^{\circ}C$ is within 5%.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.1
• /
• pp.40-44
• /
• 2013

The ball-shaped mobile robot, so called ballbot has single point contact on ground and low energy consumption in motion because of the reduced friction. In this paper, a new ballbot is presented, which has omnidirectional mobile platform inside of it as a driving system. Thus the ballbat has omnidirectional mobility without nonholonomic constraints. Kinematics and inverse kinematics of the ballbat is derived also in this paper.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.621-624
• /
• 1997

This paper presents the design procedure for soccer-playing rovots based on the centralized approach. Using a fast vision system, we obtain the configuration of each robot and then the host computer computes the desired motion and commands each robot directly via RF communication. The robot soccer game has a lot of problems such as obstacle avoidance, coordination between robots, dribbling the ball, and so on. To implement such motions, we think that the centralized approach seems to be more powerful than the distributed approach. We describe the technical tips for developing the robots in detail here and explain our strategy for getting the scores.