• 전기화학회지
• /
• 제6권3호
• /
• pp.183-186
• /
• 2003

In a PEM fuel cell electrode, backing layer has tremendous impact on electrode performance. The backing layer provides structural support for the porous electrode, distributes the reactants to the other layers and acts as a current collector. It has major influence on the water management in a PEM fuel cell. Selection of suitable backing layer material for the fabrication of electrode is thus very important to achieve high performance. In this paper we have compared the performance of PEM fuel cell electrodes fabricated using carbon paper EC-TPI-060T, carbon cloth EC-CCI-060T, (ElectroChem Inc.USA) and Carbon cloth from Textron, USA (CPW 003 grade). Mass transport problem was observed under non-pressurized condition, at high current densities, in the caie of EC-CC1-060T carbon cloth electrode (at $50^{\circ}C$), due to its higher thickness. The performance of carbon paper electrode was higher than EC-CCI-060T carbon cloth electrode. The performance of Textron carbon cloth was comparable to EC-TPI -060T carbon paper.

• KIEAE Journal
• /
• 제11권1호
• /
• pp.3-8
• /
• 2011

Sound absorbing materials used for lightweight panels and interior material are mainly made of fibroid material such as glass wool or rock wool. However these fiber type sound absorbing materials have some problems such that sound absorption could be decreased as time goes by because of durability. In addition, dust scattering from fiber type material can cause another problem in health. In this point of view, this study aims to develop environment friendly sound absorbing material using Hwangto(so called loess or yellow soil), a traditional housing material. Hwangto is natural housing material in Korea and generally known for improving indoor air quality. Hwangto panel is made to construct on the floor, wall and ceiling, and expected that there is not enough absorption. Present study tried to develop environment friendly sound absorbing material that has high sound absorption performance with good environment performance in terms of air quality. Pore rate was designed to maximize the absorption in the specific frequency bands, and two kinds of backing space were applied in order to see the effect of backing space. As a result peak frequency that has maximum absorption is going high as the pore rate is increased. The backing space provides more absorption and makes the peak frequency down to low.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.350-353
• /
• 2005

It is a feature of primary importance for a backing material for circular saw blades having teeth which are tipped with cermet, that the steel has not a too high hardenability in order that the backing material shall not be completely hardened through brazing, welding or grinding, etc. in connection with the finishing operation in the manufacturing of circular saw blade. It is believed that V-(2Mo+W) added steel from this point of view had best conditions. Using V-(2Mo+W) added backing steel, the tool failure can be effectively prevented due to superior damping performance.

• 한국철도학회논문집
• /
• 제14권2호
• /
• pp.109-115
• /
• 2011

고속철도 KTX 차량의 답면제동은 전기제동이 작용하지 않는 저속에서 열차를 정거장의 정위치에 정차시킬 때 주로 사용되는데 그 동안 균열발생, 제륜자 키 탈락 등 잦은 고장이 발생하였다. 본 연구에서는 이러한 고장의 원인을 규명하고 각 고장에 대해 해결책을 제시하고 시험평가를 통하여 개선효과를 검증하였다. 제륜자 키와 캠의 강도향상과 제륜자 마찰재 지지판의 강도향상은 제륜자 마찰재의 균열발생을 약간 줄이는 효과는 있었다. 지지판의 강도향상, 구조개선과 함께 제륜자의 재질을 변경하였을 때 마찰재에는 균열이 거의 발생되지 않았다.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권2호
• /
• pp.119-125
• /
• 1997

In this study, piezoelectric transducers were designed and manufactured using PZT-5A which had relatively high electromechanical coefficient, nondestructive testing system was developed which was able to inspect automatically using stepping motors, PC-Lab, and PC-Scope. The optimum design conditions for NDT were presented and verified comparing PZT-5A probes with comercial probes. It was proved by simulation and experiments that Epoxy is a good material as matching and backing layers. The envelope was reduced 60% with matching layer and 76% with matching and backing layer. NDT was successfully carried out for aluminum test pieces. Distance error of PZT-5A probe was 2.8%.

• 비파괴검사학회지
• /
• 제35권2호
• /
• pp.112-119
• /
• 2015

고해상도 분자 영상이 가능한 광음향 현미경의 공간해상도는 초음파 변환기에 의해 결정되기 때문에 높은 동작 주파수, 광대역, 높은 신호 수신 효율을 갖는 광음향 수신 변환기는 고성능 광음향 현미경에 필수적이다. Polyvinylidene fluoride (PVDF)는 이러한 광음향 수신 변환기 성능 확보가 가능한 압전소재이다. 그러나 PVDF는 낮은 음향 임피던스로 인해 사용되는 흡음층에 의해서 중심주파수 및 대역폭이 영향을 받게된다. 본 논문에서는 광음향 현미경에 적합한 PVDF 기반 고주파수 초음파 수신 변환기의 최적 흡음층 소재의 음향 임피던스가 최종 변환기 성능에 어떠한 영향을 주는지에 관한 연구를 수행하였다. 이를 위해 EPO-TEK 301, E-Solder 3022, RTV를 각각 흡음층 물질로 사용하여 고주파수 초음파 수신 변환기를 제작하고 그 음향 특성을 평가하였다. 제작된 변환기의 공간해상도를 평가하기 위해 $25{\mu}m$ 직경을 갖는 철심을 표적으로 사용하여 영상을 획득하였으며, 실험을 통해 얻은 펄스-에코 신호 크기 및 중심주파수, -6 dB 대역폭, 공간해상도 평가를 통해 PVDF의 음향 임피던스보다 약간 높은 음향 임피던스를 갖는 EPO-TEK 301이 가장 적합한 흡음층 물질임을 알 수 있었다.

• The Journal of the Acoustical Society of Korea
• /
• 제25권2E호
• /
• pp.79-84
• /
• 2006

Acoustic characteristics of a sound absorbing material can be identified, if the characteristic impedance and propagation constants are known, which have generally been determined experimentally. One easy method determining these two essential parameters is to measure the one dimensional wave characteristics in the impedance tube. In th udy, the effects of backing conditions on the impedance tube measurement have been examined using several pairs of generally used end conditions. The results showed that the measured values are similar for most pairs of end conditions: however, it was observed that the measured characteristic impedance for different thickness did not agree well for some pairs. In this work, the multi termination method, using three or more known backing con ns, was suggested to reduce such random errors, which are mostly caused by the test procedure. Employing three terminations as a set, comprised of a rigid end, an end with porous material, and an end with a backing cavity, it was demonstrated that improved measured results could be obtained for an open cell PU foam varying widely with three different thicknesses.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제7권2호
• /
• pp.315-323
• /
• 2015

The weld scallop has been used for joining T-bars. There are a lot of weld scallops in shipbuilding. It is difficult to perform scallop welding due to the inconvenient welding position. This results in many problems such as porosity, slag inclusion, etc. In this study, a new method is devised to remove weld scallops by incorporating a Ceramic Backing Material (CBM). The weld scallop is removed by an elongation of the v groove. In order to insert a CBM into the groove without a weld scallop, a wedge-shaped CBM is developed. The top side of the developed CBM is similar to the shape of a general back bead. The bottom surface has a saw-toothed shape for cutting at a suitable length. This can be attached to the root side of a face plate using adhesive tape, just like a general CBM. Welding experiments in normal and abnormal conditions are carried out and the possibility of burn-through is examined. This CBM's applicability to shipbuilding is verified.

• 비파괴검사학회지
• /
• 제9권1호
• /
• pp.69-76
• /
• 1989

Piezoelectric elements, backing and shoe material are the important components of the ultrasonic transducer. In this study, characteristic constants in the domestic and the foreign PZT ceramic elements are investigated, The acoustic properties of the domestic and the foreign backing and shoes are characterized. The effects of components characteristics, the kinds of the piezoelectric elements and the thickness of the wear plates are investigated for the manufactured normal beam ultrasonic transducers.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 추계학술대회 논문집
• /
• pp.245-248
• /
• 1996

In this study, piezoelectric transducers were designed and manufactured using PZT-5A which had relatively high electromechanical coefficient, NDT system was developed with was able to inspect automatically using stepping motors, PC-Lab, and PC-Scope The optimum design conditions for NDT were presented and verified comparing PZT-5A probes with comercial probes. It was proved with comercial probes. It was proved by simulation and experiments that Epoxy is good as material of matching and backing layers. The envelope was reduced 60% with matching layer and 76% with matching and backing layer. NDT was successfully carried out for aluminum test pieces. Distance error of PZT-5A probe was 2.8%.