• The Journal of the Korea Contents Association
• /
• v.21 no.6
• /
• pp.44-50
• /
• 2021

In this paper, we analyze the efficiency of light sources of CCFL and LED monitors. Cold Cathode Fluorescent Lamp (CCFL), which is widely used as a light source for LCD display, supplies a high voltage of 1,200[V] or more when it is initially driven. In addition, a constant normal voltage of 400 ~ 800[V] after lighting, and 3 ~ 6[ mA] is needed for a power circuit that can stabilize the current. Applying a high voltage causes a lot of stress on the inverter and generates a lot of heat in the cold cathode lamp, causing significant damage to the BLU (Back Light Unit), resulting in a burning phenomenon, which causes the screen to output normal colors when outputting the screen. We can not see the yellow output and the screen darkened. Therefore, in order to prevent such a symptom in advance, efficiency can be increased by using a Light Emitting Diode (LED) as the light source of the LCD display instead of a cold cathode fluorescent lamp (CCFL). As a result, it is shown that the LED method outperforms the CCFL method.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.694-697
• /
• 2003

In applying LCD to TV application, one of the most significant factors to be improved is image sticking on the moving picture. LCD is different from CRT in the sense that it's continuous passive device, which holds images in entire frame period, while impulse type device generate image in very short time. To reduce image sticking problem related to hold type display mode, we made an experiment to drive LCD like CRT. We made articulate images by turn on-off backlight, and we realized the ratio of Back Light on-off time by adjusting between on time and off time for video signal input during 1 frame (16.7ms). Conventional CCFL (cold cathode fluorescent lamp) cannot follow fast on-off speed, so we evaluated new fluorescent substances of light source to improve residual light characteristic of CCFL. We realized articulate image generation similar to CRT by blinking drive. As a result, reduced image sticking phenomenon was validated by naked eye and response time measurement.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.4
• /
• pp.30-35
• /
• 2020

The light guide plate (LGP) provides a surface light source on the back of the liquid crystal display (LCD), which is not self-emitting; thus, it is an essential component of display units requiring sufficient brightness. To maximize the light-emitting effect of an LGP, enough incident light, from the light source, should enter into its side. However, the current trend in LCD panels is represented by larger and thinner screens and this smaller thickness prevents the accordingly thin LGPs from providing sufficient brightness. This paper proposes a process for manufacturing wedge-type LGPs, which might increase the amount of incident light and, consequently the surface light emission, for applications in large LCDs. The proposed method was validated by building a dedicated manufacturing machine and performing illuminance experiments on the fabricated LGP.

• Korea-Australia Rheology Journal
• /
• v.19 no.3
• /
• pp.171-176
• /
• 2007

LCD-BLU (Liquid Crystal Display-Back Light Unit) of medium size is usually manufactured by forming numerous dots with $50{\sim}300\;{\mu}m$ in diameter by etching process and V-grove shape with $50\;{\mu}m$ in height by mechanical cutting process. However, the surface of the etched dots is very rough due to the characteristics of the etching process and V-cutting needs rather high cost. Instead of existing optical pattern made by etching and mechanical cutting, 3-dimensional continuous micro-lens of $200\;{\mu}m$ in diameter was applied in the present study. The continuous micro-lens pattern fabricated by modified LIGA with thermal reflow process was tested to this new optical design of LGP. The manufacturing process using LIGA-reflow is made up of three stages as follows: (i) the stage of lithography, (ii) the stage of thermal reflow process and (iii) the stage of electroplating. The continuous micro-lens patterned LGP was fabricated with injection molding and its test results showed the possibility of commercial use in the future.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.502-503
• /
• 2005

본 연구에서는 TFT-LCD(Thin Film Transistor-Liquid Crystal Display)의 배경광원인 BLU(Back Light Unit)의 고효율화, 고품질화를 통한 원가 절감을 달성하기 위해 BLU의 대표적 핵심부품중에 하나인 프리즘 시트를 사용하지 않는 구조의 MNT용 BLU를 개발하는데 목적을 두었다. 고효율의 BLU를 만들기위하여 17인치 BLU의 도광판의 상, 하면에 Prism 형상을 구현하였으며, 광학적 시뮬레이션을 통하여 먼저 가능성을 검토하였고, UV에 반응하는 Resin을 경화시키는 방법을 이용하여 일반 도광판에 프리즘형상을 각인(Imprint)시키는 방법으로 실물을 재현하였다. 실험 결과 프리즘 시트를 사용하지 않는 구조의 MNT용 17인치 BLU에서 중심휘도 4,984nit, 균일도 70% 달성하였다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.269-272
• /
• 2008

LGP is a key component of LCD back light unit because it determines the brightness and sharpness of display image. Usually, it has optical patterns fabricated on the bottom surface. In the present paper the LiGA-reflow method was applied to fabricate the LGP mold. Furthermore, the optical simulation considering the replication ratio of pattern height was applied to the pattern design. The optical simulation through systematic correction scheme helped find the optimum distribution of pattern density. Finally, the stamper fabricated by this method was installed in the mold and LGP was produced by injection molding. As a result of luminance measurement for the final product, the average luminance and luminance uniformity was measured 3,180 nit and 84%, respectively. Consequently, the mold fabrication method using the LiGA-reflow and optical simulation(CAE) can save the expense and time compared with the existing fabrication methods(laser ablation and chemical etching).

• Electronics and Telecommunications Trends
• /
• v.30 no.6
• /
• pp.42-49
• /
• 2015

질화물 반도체 기반 가시광 청색 Light Emitting Diode(LED) 기술은 디스플레이의 Back Light Unit(BLU)뿐 아니라 일반 조명에 활용되며 우리 실생활에서 매우 밀접하게 사용하고 있다. 가시광보다 짧은 파장을 가지는 자외선 LED의 경우 경화기 및 위폐감지기에 기존의 유해 가스를 사용하는 자외선 램프를 대체하고 있다. 자외선 광원의 또 다른 거대 시장으로 살균 및 정화, 의료 및 바이오 응용 시장에서 자외선 램프를 대체할 수 있는 자외선 LED 기술이 활발히 발전하고 있다. 본고에서는 이들 자외선광원 시장동향과 국내외 자외선 LED의 기술동향을 파악하므로 앞으로 연구개발의 방향을 모색하고자 한다.

• Design & Manufacturing
• /
• v.2 no.5
• /
• pp.1-4
• /
• 2008

LCD-BLU (Liquid Crystal Display - Back Light Unit) is one of kernel parts of LCD unit and it consists of several optical sheets(such as prism, diffuser and protector sheets), LCP (Light Guide Plate), light source (CCFL or LED) and mold frame. The LGP of LCD-BLU is usually manufactured by forming numerous dots with $50-200{\mu}m$ in diameter on it by erosion method. But the surface of the erosion dots of LGP is very rough due to the characteristics of the erosion process during the mold fabrication, so that its light loss is high along with the dispersion of light into the surface. Accordingly, there is a limit in raising the luminance of LCD-BLU. Especially, the negative and positive micro-lens pattern fabricated by modified LiGA with thermal reflow process was applied to the optical design of LGP.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.94-96
• /
• 2001

As a batch Type device, this machine is contrive to seal glass plates for plasma BLU (Back Light Unit) by indirect heating from electric heaters. In order to maintain the heating / cooling Chambers clean, this machine uses a muffle formation. The components of the machine are listed bellow.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.04a
• /
• pp.160-164
• /
• 2003

LCD를 TV 향으로 적용하기 위해서는 몇 가지 해결해야만 하는 문제가 있으며, 이중 하나가 동화상 재생시에 발생하는 잔상현상의 해결이다. LCD는 기존의 CRT와 같은 불연속 자발광 소자가 아니라, 연속수광소자로서, 잔상현상이 치명적인 약점으로 나타난다. 기종의 Monitor 대응품에서는 실제로 Monitor를 통해서 사용자가 관찰하는 이미지 정보가 정지화상 중심으로 구성되어 있기 때문에 문제가 되지 않았으나, TV의 경우 연속적인 동화상만을 취급하고 있어, 잔상현상의 해결 없이는 TV 향 제품에 적용할 수 없다. 따라서 본 연구에서는 잔상현상을 근본적으로 없애기 위해서 LCD를 CRT와 같이 불연속적의 분절적 이미지로 구동하는 방법을 실험하였으며, VIDEO 입력 신호에 대해서 16.7msec의 1Frame을 기준으로 점등 구간과 비점등 구간을 6:4로 나누어 BL(Back Light)을 점멸하는 방법을 구현하였다. 또한 종래의 CCFL(cold Cathod Flourescent Lamp)로는 점멸 속도에 대한 대응이 불가하므로, 이를 해결하기 위해서 광원의 형광체에 대해서 잔광시간특성의 개선도 동시에 실시하였다. 실험 결과 육안 및 사진촬영에서 잔상없는 화면을 얻을 수 있었으며, 응답파형 측정 결과 CRT 측정시와 마찬가지로 분절적인 이미지의 생성이 가능한 것을 알 수 있었다.