• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.55 no.4
• /
• pp.161-164
• /
• 2006

In this thesis we designed the vision system to inspect the defect of a back light unit of plat panel display device. The vision system is divided into hardware and inspection algorithm of defect. Hardware components consist of illumination part, robot-arm controller part and image-acquisition part. Illumination part is made of acrylic panel for light diffusion and five 36W FPL's(Fluorescent Parallel Lamp) and electronic ballast with low frequency harmonics. The CCD(Charge-Coupled Device) camera of image-acquisition part is able to acquire the bright image by the light coming from lamp. The image-acquisition part is composed of CCD camera and frame grabber. The robot-arm controller part has a role to let the CCD camera move to the desired position. To take inspections of surface images of a flat panel display it can be controlled and located every nook and comer. Images obtained by robot-arm and image-acquisition board are saved on the hard-disk through windows programming and are tested whether there are defects by using the image processing algorithms.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.5
• /
• pp.189-192
• /
• 2011

A flexible back-light unit (FBLU) is fabricated by embedding plasma discharge clusters in a flexible polymer matrix. The brightness uniformity of an FBLU was measured for various combinations of optical sheets and compared with the simulated results for various bending angles. A gap between light sources causes distinctive integrated brightness curves which have two inflection points depending on bending angle. The brightness distribution of a simulated BLU was in good agreement with that of an actual plasma BLU except for a dark area that appeared at the center of the simulated BLU. The real and simulated BLUs both clearly showed an angle dependency caused by mirror images located between point light sources. On the basis of these results, it is suggested that these mirror-like images could be a major factor in determining the characteristics of FBLUs.

• Proceedings of the Optical Society of Korea Conference
• /
• 2007.02a
• /
• pp.257-258
• /
• 2007

• Information Display
• /
• v.2 no.1
• /
• pp.45-51
• /
• 2001

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1048-1052
• /
• 2008

Difficulties in developing process of Liquid Crystal Display(LCD) products such as frequent design modifications, various design requirements, and short-term development period bring on the need of integrated design approach that is efficient and easy to handle. Back Light Unit(BLU) of the LCD, which drastically affects the optical performance of LCD products, is divided into in-coupling part and out-coupling part. Serration of the in-coupling part flattens the light received from point light sources and dot pattern of the out-coupling part regularizes the light sent to screen. Therefore, the optical performance of a LCD product is largely influenced by the shape of serration and the arrangement of dot pattern. In this research, a new design approach which enables to improve the optical performance of LCD products and overcome the prementioned difficulties in developing process of LCD products is proposed. The shape of serration is parameterized to 3 parameters and out-coupling part is partitioned into 10 partitions to apply the optimization technique to this problem. 3 parameters for the shape of serration and densities of 10 partitions are used as design variables in the design optimization. Optical simulation tool named SPEOS is used to evaluate the optical performance of the LCD product. Since the optical simulation uses the random ray tracing technique, numerical noise may possibly be included in the simulation process. To solve the problem caused by numerical noise, the PQRSM which can stably find the solution of the noise problem is used in this research.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.277-280
• /
• 2007

Field emission-back light unit (FE-BLU) was fabricated using carbon nanotube (CNT) emitter. Local dimming and local brightening techniques were achieved, which results in very high contrast ratio. In addition, the motion blur phenomenon, one of the serious problems of liquid crystal display (LCD) with cold cathode fluorescent lamp (CCFL)-BLU, was removed from LCD-TV by using FE-BLU.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1271-1276
• /
• 2008

This study has explained about LED for BLU which is widely used in the kinds of display devices or lighting. It was shown that the open due to delamination were the dominant LED for BLU failure mode and mechanisms from failure analysis of LED samples. Then, we have defined failure as yellowing and 100% reduction of light output intensity of LED for BLU and acceleration factors as temperature and current in Accelerated Life Test(ALT). Finally, we have estimated the Weibull distribution, life-stress relationship, and accelerating factor is used by ALTA Software.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.728-731
• /
• 2005

A light guide panel (LGP) is an element of the LCD back light unit, which is used for display devices. In this study, a laser marking process is applied to the fabrication of light guide panels as the new fabrication process. In order to obtain a light guide panel which has high luminance and uniformity, four principal parameters such as power, scanning speed, ratio of line gap, and number of line were selected as important factors. A Web-based design tool was developed to generate patterns of light guide panel, and the tool may assist the designer to develop optimized patterns. Topcon-BM7 was used for luminance measurement of each specimen 100mm$\times$100mm area. By Taguchi method optimized levels of each parameters such as 40W of power, 30mm/s of scanning speed, 100:50 ratio of pattern gap, and 90 line of pattern were found by Taguchi method.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.4 s.181
• /
• pp.91-98
• /
• 2006

A light guide panel (LGP) is an element of the LCD back light unit, which is used for display devices. In this study, the laser marking process is applied to the fabrication of light guide panels as the new fabrication process. In order to obtain a light guide panel which has high luminance and uniformity, four principal parameters such as power, scanning speed, ratio of line gap, and number of line were selected. A Web-based design tool was developed to generate patterns of light guide panel at any location, and the tool may assist the designer to develop optimized patterns. Topcon-BM7 was used for luminance measurement of each specimen with $100mm{\times}100mm$ area. By Taguchi method optimized levels of each parameters were found, and luminance of $3523cd/cm^2$ and uniformity of 92% were achieved using the laser machined BLU.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.145-147
• /
• 2009

The cost effective structures and materials for the carbon nanotube (CNT) back light unit (BLU) are proposed. Simplified device structures and related electron emitter materials are prepared. CNT emitters were screen printed or remotely mounted on the back plate, and this enabled less than two photo patterning steps. Besides the cost benefits, operating voltage was dramatically decreased and higher current density was obtained