• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2003년도 학술대회 논문집
• /
• pp.203-205
• /
• 2003

Parallel wounded windings with BSCCO-2223 HTS tape for 1MVA HTS transformer were designed and prototype windings were fabricated in double pancake type. The parallel HTS tapes were transposed between the pancakes via non-superconducting joints because it is hard to make transpositions inside the pancake windings. The prototypes were wound using copper tape with same size as BSCCO-2223 tape, which will be used in 1MVA HTS transformer. The windings will be used for high voltage test and insulation test of the transformer Parallel HTS windings are going to be fabricated and tested for current distribution in near future.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2003년도 High Temperature Superconductivity Vol.XIII
• /
• pp.77-77
• /
• 2003

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 춘계학술대회 논문집
• /
• pp.98-101
• /
• 2005

BSCCO thin films fabricated by using the evaporation method. As a result, although the composition of Bi2212 was set up, the phase of Bi2201, Bi2212 and Bi2223 was formed. The formation area of these stable phases is indicated as inclined line in the direction of the right lower end from the Arrhenius plot of the substrate temperature-oxidation gas pressure, and are distributed in very small area. The activation energy for the phase transformation from the Bi2201 to the Bi2212 is estimated in terms of the Avrami equation.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2008년도 High Temperature Superconductivity Vol.XVIII
• /
• pp.46-46
• /
• 2008

• Progress in Superconductivity
• /
• 제3권2호
• /
• pp.193-197
• /
• 2002

There are many problems in wire fabrication of long length Bi-2223 superconductor by using conventional extrusion method. They are mainly due to high surface resistance and inhomogeneous distribution of inner stress. Hydrostatic extrusion process will not only decrease the extrusion pressure but also enhance homogeneous deformation of material by reducing friction force between billet and container Hydrostatic extrusion method is considered to be useful fur fabrication of the homogeneous wire with high density. In this paper, hydrostatic extrusion process is introduced to fabricate Bi-2223 superconducting tape, and also discussed are the interface homogeneity and microstructural aspects of extruded BSCCO/Ag billet.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 초전도 자성체
• /
• pp.17-20
• /
• 2002

The effects of relatively low lead content (0.2~0.3) on the 2223 phase formation and transport property of Bi-2223/Ag tapes have been investigated. The results show that lead contents have great impact on the phase assemblage of precursors, subsequently, on the phase formation and transport property of silver sheathed BSCCO-2223 tapes. Powders containing Pb=0.25 and Pb=0.3 resulted in the nearly identical $J_c$ values in fully processed tapes, but leaded to significant difference on the phase formation process. For the case of Pb=0.2, both low conversion fraction of 2212 to 2223 and low $J_c$ value were obtained in final reacted tape, which was probably due to lack of enough liquid phase to facilitate the phase transformation.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2009년도 Korea Superconductivity Society Meeting 2009
• /
• pp.58-58
• /
• 2009

• 한국초전도ㆍ저온공학회논문지
• /
• 제5권1호
• /
• pp.40-43
• /
• 2003

The phase transformation, variation of secondary phase, and critical current density $(J_c) for (Bi,Pb)_2Sr_2Ca_2Cu_3O_10 (2223)$ tapes have been studied through the thermal slide heat treatment (TSHT) process. This process consists of a multiple variations of oxygen partial pressures and temperatures at the initial heat treatment During the initial heat treatment some secondary phase such as $(Ca,Sr)_2CuO_3(2/1 AEC), (Ca,Sr)_{14}Cu_{24}O_{41} (14/24 AEC), and (Bi,Pb)_2Sr_2CuO_y$(2201, amorphous phase) farm in Bi-2223 tapes, especially at the 2223 grain boundaries. These secondary phases are detrimental to the phase transformation and final properties. In order to control the secondary phase in Bi-2223 tapes the amount and size of secondary phases among the TSHT process were observed. The results indicate that the amount and particle size of AEC particles were smaller when the TSHT process was used than when the normal process at the initial heat treatment was used which results in the improved $J_c$ properties after the final process.

• Progress in Superconductivity
• /
• 제4권2호
• /
• pp.168-171
• /
• 2003

It was known that properties of superconducting tapes could be influenced by mechanical processing method. In this presentation, the effect of drawing method on the final properties of superconductor tape has been systematically studied. Firstly, BSCCO/Ag tapes have been fabricated via two-stage drawing method and conventional rolling process. The two-stage drawing process consists of circular dies drawing and rectangular dies drawing. Important parameters such as fill factor and critical current values of fully processed superconducting tapes have been evaluated to elucidate the effect of drawing method.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 1999년도 제1회 학술대회논문집(KIASC 1st conference 99)
• /
• pp.18-21
• /
• 1999

The effects of joining process such as contact method, shape of joined area and pressure on the properties of Bi-2223 superconducting tape have been optimized. In the process tapes were etched to expose the superconductor core in the shape of 'ㅁ' and 'ㄷ'. The exposed cores of the two tapes were brought into contact, uniaxially pressed and sintered. Subsequently, the current capacity of the joined tape was measured as a function of uniaxial pressure. It was observed that the current capacity was significantly dependent on uniaxial pressure. The joined tape, fabricated with a pressure of 1,600 MPa, showed the highest value of current capacity(90%) of highest value of current capacity is resulted from improvements in core density, contacting area and grain alignment, etc. In addition the effect of processing variables on microstructural evolution and mechanical property of joined tape will be presented.