• Corrosion Science and Technology
• /
• 제8권2호
• /
• pp.53-61
• /
• 2009

In this study, both evaluations by visual imaging for exterior view of coating and by EIS were executed for epoxy primer coated specimens deteriorated by accelerated test, and comparison and analysis were carried out for 2 evaluation methods. In the comparison between total damaged area ratio acquired by image processing method and deterioration point, higher deterioration points were appeared for rusted specimens than for non-rusted specimens. It is attributed that deterioration point per unit area ratio given for rust is higher than for peeling. In the comparison between total damaged area ratio and EIS result, impedance of coating was largely decreased as about TEX>$10^4{\Omega}{\cdot}cm^2$ or less when rust area ratio is more than about 0.1%, and blistering area ratio is more than about 3%. Charge transfer resistance ($R_{ct}$) and double layer capacitance ($C_{dl}$) values were appeared for all specimens except 2 ones, which shows that water is accumulated and steel substrate is corroded at coated film-steel interface. In the comparison between deterioration point and EIS result, more than 10 points as deterioration point were given for specimens of below $10^6{\Omega}{\cdot}cm^2$ of impedance at low frequency. For specimens deteriorated by NORSOK cyclic test, impedance was lowest of all, though deterioration point was not high. It is thought to be attributed that coating system and accelerated deterioration condition of cyclic tested specimens were different from those of main specimens. From the result, it is thought that coating resistance can be relatively more decreased than deterioration degree estimated from exterior view under more severe corrosion environment or in the present of more complex deterioration factors.

• Journal of the Korean Society of Hazard Mitigation
• /
• 제9권4호
• /
• pp.1-9
• /
• 2009

This paper investigates inelastic lateral-torsional buckling of stepped beams subjected to uniformly distributed load and end moments. A three-dimensional finite-element program ABAQUS (2007) and a regression program MINITAB(2006) were used to analytically develop new design equation for singly and doubly stepped beams with simple boundary condition. The flanges of the smaller cross-section in the stepped beams were fixed at 30.48 by 2.54 cm, whereas the width and thickness of the flanges of the larger cross-section varied. The web thickness and height of the beams were kept at 1.65 cm and 88.9 cm, respectively. The ratios of the flange thickness, flange width, and stepped length of beam are considered with analytical parameters. Two groups of 27 cases and 36 cases, respectively, were analyzed for doubly and singly stepped beams in the inelastic buckling range. The combined effects of residual stresses and geometrical imperfection on inelastic lateral-torsional buckling of beams are considered. The distributions of residual stress of the cross-section is same as shown in Pi and Trahair (1995) and the initial geometric imperfection of the beam is set by central displacement equal to 0.1% of the unbraced length of beam. The comparisons between results from proposed equations and the results from finite element analyses were presented in this paper. The maximum differences of two results are of 13% for the doubly stepped beam and 10% for the singly stepped beam. The proposed equations definitely improve current design methods for the inelastic lateral-torsional buckling problem and increase efficiency in building and bridge design.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• 제20권4호
• /
• pp.359-366
• /
• 2002

To survey satellites using only GPS can sometimes cause an impossible situation due to the many different geographical conditions as city cannon and obstacles. Although the GLONASS satellite system does not have the ability to survey itself accurately since it currently lacks of the number of usable satellites, it is able to bridge the gap when combined with GPS. This research used the GPS receiver to perform four analyzing methods to bring out the independent surveying method of GPS and combined surveying method of GPS and GLONASS(4 methods - number of satellites able to receive, precision of raw data, standard deviation from known point and RTK surveying). The result of test surveying satellites showed that 11 hours were possible to measure a minimum of 4 satellites when using an independent surveying method and 4 hours in unified surveying method in a month. Also, the precision of raw data using GPS and GLONASS surveying is 0.08~l.8m better than the GPS surveying in standard deviation. The deviation of known points by GPS and GLONASS also showed better accuracy by 3~l1mm. The RTK showed the range of differences in deviation of survey by leaning towards the GPS independent survey in Northing coordinate and leaned towards the Easting coordinate when GPS and GLONASS were combined. Nonetheless, it can't be said that the unified method is better, because it has limits to its capability.

• Journal of the Earthquake Engineering Society of Korea
• /
• 제10권3호
• /
• pp.47-55
• /
• 2006

Seismic performance and retrofit of reinforced concrete (RC) two-column piers widely used at roadway bridges in Korea was experimentally evaluated. Ten two-column piers that were 400 mm in diameter and 2,000 mm in height were constructed. These piers were subjected to hi-directional cyclic loadings under a constant axial load of $0.1f_{ck}A_g$. Test parameters were the confinement steel ratio, loading pattern, lap splice of longitudinal reinforcing bars, and retrofitting method. Specimens with lap-spliced longitudinal bars were retrofitted with steel jacket, pre-stressing steel wire, and steel band. Test result showed that while the specimens subjected to bi-directional lateral cyclic loadings which consisted of two main amplitudes in the transverse axis and two sub amplitudes in longitudinal axis, referred to as a T-series cyclic loadings, exhibited plastic hinges both at the top and bottom parts of the column, the specimens subjected to bi-directional lateral cyclic loadings in an opposite way, referred to as a L-series cyclic loadings, exhibited a plastic hinge only at the bottom of the column. The displacement ductility of the specimen under the T-series loadings was bigger than that of the specimen under the L-series loadings. Specimen retrofitted with pre-stressing steel wires exhibited poor ductility due to the upward shift of the plastic hinge region because of over-reinforcement, but specimens retrofitted with steel jacket and steel band showed the required displacement ductility. Steel band can be an effective retrofitting scheme to improve the seimsic performance of RC bridge piers, considering its practical construction.

• Proceedings of the Korea Water Resources Association Conference
• /
• 한국수자원학회 2016년도 학술발표회
• /
• pp.447-447
• /
• 2016

홍수 시 하천을 따라 유하되는 유송잡물(잡목, 생활쓰레기 등)은 구조물에 집적이 이루어지며 이로 인해 물의 흐름을 방해하고 구조물 주변의 지반을 약화시키거나 월류로 인해 심각한 피해를 야기 시킨다. 교량의 경우 유송잡물의 집적은 교각의 항력을 증가시켜 전도파괴를 유발시킬 수 있으며, 교각주변 흐름교란을 통한 하상세굴로 인해 기초부를 파괴시키기도 한다. 또한 통수단면적 증가로 인해 높아진 수위는 제방을 월류시켜 재산 및 인명피해를 유발하기도 한다. 암거의 경우 유송잡물을 포함한 토사로 인해 단면폐색 및 침식으로 암거의 파괴를 발생시키고 이로인해 도로의 단절을 가져오기도 한다. 이러한 유송잡물에 대한 차단대책은 현재 까지 유지관리를 통한 방법만이 최선책으로 제시되고 있다. 본 연구는 국외에서 소개되고 있는 유송잡물 피해저감시설을 대상으로 축소모형실험을 통해 효과를 확인하고 이를 통해 저감시설의 효율에 대해 소개하고자 하는 것이 주목적이다. 유송잡물 저감시설은 교량의 경우 수직분리대 방법, 우회말뚝 방법, 스위퍼를 이용한 방법으로 소개하고 있으며 이들 방법의 특징은 유송잡물 우회를 통해 집적을 저감하는 방식이다. 암거의 경우 수직분리대 방법, 스크린 방법, 우회스크린을 이용하는 방법 등이 있으며 수직분리대는 교량과 마찬가지로 우회방식을 기본방식으로 스크린 방식은 유송잡물의 차단을 원칙으로 하고 있다. 실험의 결과는 교량과 암거의 차단시설 유무에 따른 유송잡물의 집적률을 대상으로 하였다. 차단시설이 없는 경우 교량에서의 집적률은 97.9% ~ 99.2%의 집적률로 나타났다. 수직분리대의 경우 유송잡물 집적률은 49.3%, 우회말뚝은 0.0% ~ 4.2%의 범위로 매우 높은 차단효과를 보이고 있었다. 스위퍼방식의 경우 집적률은 5.3% ~ 20.9%로 나타났다. 이러한 결과로 판단하였을 때 차단시설 설치로 인한 교량에 대한 직접적인 차단효과는 수직분리대 < 스위퍼 < 우회말뚝 순으로 높은 차단효과를 보이는 것으로 나타났다. 그러나 우회말뚝에서의 집적률이 한계치를 넘어선다면 유송잡물로 인해 흐름교란, 수위 및 하상변동, 말뚝의 유실 등으로 인한 피해가 예상된다. 암거대상 유송잡물 차단시설 실험결과는 수직분리대의 경우 type과 투하방법에 따라 차이가 있지만 집적률은 14.7% ~ 64.9%의 범위로 나타났다. 스크린과 우회스크린 방식은 유송잡물의 우회가 아닌 차단이 목적이므로 유송잡물 집적에 의한 수위상승이 우려되는바 수위영향을 검토하였다. 검토결과 스크린 설치로 인한 수위상승이 우회스크린보다 높게 상승하는 것으로 나타났다. 이러한 결과는 스크린의 형태적인 측면에서 2면을 통해 집적되는 특성을 갖는 우회스크린이 통수단면적을 많이 확보하기 때문이다. 따라서 국부적인 수위상승으로 인한 피해를 저감하기 위해서는 설치여건이 허용된다면 통수단면적 확보가 유리한 우회스크린 설치가 유리할 것으로 판단된다.

• Journal of Korea Water Resources Association
• /
• 제54권12호
• /
• pp.1285-1294
• /
• 2021

In recent years, as rainfall is concentrated and rainfall intensity increases worldwide due to climate change, the scale of flood damage is increasing. Rainfall of a previously unobserved magnitude falls, and the rainy season lasts for a long time on record. In particular, these damages are concentrated in ASEAN countries, and at least 20 million people among ASEAN countries are affected by frequent flooding due to recent sea level rise, typhoons and torrential rain. Korea supports the domestic flood warning system to ASEAN countries through various ODA projects, but the communication network is unstable, so there is a limit to the central control method alone. Therefore, in this study, an artificial intelligence-based flood prediction model was developed to develop an observation station that can observe water level and rainfall, and even predict and warn floods at once at one observation station. Training, validation and testing were carried out for 0.5, 1, 2, 3, and 6 hours of lead time using the rainfall and water level observation data in 10-minute units from 2009 to 2020 at Junjukbi-bridge station of Seolma stream. LSTM was applied to artificial intelligence algorithm. As a result of the study, it showed excellent results in model fit and error for all lead time. In the case of a short arrival time due to a small watershed and a large watershed slope such as Seolma stream, a lead time of 1 hour will show very good prediction results. In addition, it is expected that a longer lead time is possible depending on the size and slope of the watershed.

• Tuberculosis and Respiratory Diseases
• /
• 제85권3호
• /
• pp.249-255
• /
• 2022

Background: The main cause of death in pulmonary embolism (PE) is right-heart failure due to acute pressure overload. In this sense, extracorporeal membrane oxygenation (ECMO) might be useful in maintaining hemodynamic stability and improving organ perfusion. Some previous studies have reported ECMO as a bridge to reperfusion therapy of PE. However, little is known about the patients that benefit from ECMO. Methods: Patients who underwent ECMO due to pulmonary thromboembolism at a single university-affiliated hospital between January 2010 and December 2018 were retrospectively reviewed. Results: During the study period, nine patients received ECMO in high-risk PE. The median age of the patients was 60 years (range, 22-76 years), and six (66.7%) were male. All nine patients had cardiac arrests, of which three occurred outside the hospital. All the patients received mechanical support with veno-arterial ECMO, and the median ECMO duration was 1.1 days (range, 0.2-14.0 days). ECMO with anticoagulation alone was performed in six (66.7%), and ECMO with reperfusion therapy was done in three (33.3%). The 30-day mortality rate was 77.8%. The median time taken from the first cardiac arrest to initiation of ECMO was 31 minutes (range, 30-32 minutes) in survivors (n=2) and 65 minutes (range, 33-482 minutes) in non-survivors (n=7). Conclusion: High-risk PE with cardiac arrest has a high mortality rate despite aggressive management with ECMO and reperfusion therapy. Early decision to start ECMO and its rapid initiation might help save those with cardiac arrest in high-risk PE.

• Tuberculosis and Respiratory Diseases
• /
• 제42권6호
• /
• pp.823-830
• /
• 1995

Background: It has been found that Helper T cells in the peripheral blood are decreased in the cell mediated immunity in the pulmonary tuberculosis. But it has not been confirmed yet that only decrease in number of cells which has phenotype in the peripheral blood is defined to decrease in cell mediated immunity. The immunocytochemical study was performed to observe the change of the percentage of T-lymphocytes with their subsets and activated T cells in the peripheral blood of pulmonary tuberculosis and to know how many T cells would be activated, relative to resting cells in the peripheral blood. Methods: The peripheral blood obtained from twenty two patients and ten healthy controls were smeared on the gelatin coated slide glass prepared for of mononuclear cells. The double bridge technique of alkaline phosphatase-antialkaline phosphatase(APAAP) method was used. As the primary antibodies, $T_1$(anti-human T cell), $T_4$(anti-human helper/inducer T cells) and $T_8$(anti-human supressor/cytotoxic T cell) antibodies and interleukin-2 receptor (for early activated T cell), very late activation antigen (for activated cytotoxic T cell), T cell lineage specific activation antigen monoclonal actibodies were used. Results: 1) There were significantly decrease in the absolute number of $T_4$(+) cells but significantly increase of $T_8$(+) cells in the peripheral blood of pulmonary tuberculosis (p<0.05). 2) The percentage of $T_4$(+) cells showed significantly decrease in pulmonary tuberculosis but $T_8$(+)cells significantly increase(p<0.05). $T_4(+)/T_8(+)$ ratio showed significantly decrease in the peripheral blood of the pulmonary tuberculosis(p<0.05). 3) There were significantly increase in the absolute number of variable stages of activated T cells in the peripheral blood of the pulmonary tuberculosis(p<0.05). 4) The percentage of IL-2R, VLA-1, TLiSA were 6.45+1.56%, $7.64+1.34^*$, 10.45+1.16% in order which showed significantly increase in the peripheral blood of the pulmonary tuberculosis(p<0.05). Conclusion: We speculate that only a few percentage of T lymphocyte is activated in cell mediated immunity in pulmonary tuberculosis.

• Journal of Technologic Dentistry
• /
• 제37권3호
• /
• pp.131-144
• /
• 2015

Purpose: This study set out to propose plans for more efficient and effective clinical practice by investigating the current state of clinical practice in the field of dental technology and thus provide basic data to develop pre- and post-education programs for clinical practice. Methods: The subjects include dental technicians at dental technical laboratories that were appointed as the place of clinical practice by the Department of Dental Technology of G University. The survey period spanned from December 22, 2014 to January 20, 2015. Total 250 questionnaires were distributed to them, and 190(76.0%) were returned. After excluding 23 whose answers were uncertain or seemed to lack reliability, total 167(66.8%) were used in final analysis. Results: 1. The most frequent practice the student did during clinical practice was articulator attachment, which was followed by pin operation or model making, one's own task and practice, sand and crow sculpturing, burying, casting, and grinding. 2. In case of going through the entire process, porcelain had the most students at 39(23.4%), being followed by crown & bridge at 28(16.8%), clinical model at 23(13.8%), full denture at 17(10.2%), and partial denture at 17(10.2%) in the order. 3. Of the students, 59.8%(30.5% for reinforced basic practice; 29.3% for intensive practice education) said that intensive practice education should be reinforced in school; and 22.3% said that intensive theory and practice education was needed, which indicates that 82.6% voiced their opinion of reinforcing education around practice. 4. The students felt that they lacked diligence, passion, and theoretical knowledge somewhat and were relatively good at clinical adaptation and operational skills. Conclusion: The findings show that the students felt an absolute lack of practice education as the school education was focused on theory and national exams in the field of dental technology, thus raising a need to reinforce practice education. Of all the respondents, 62.9% said there was a need to improve the current education with a focus on jobs. In future, education of dental technology should work to bring up able dental technicians that can perform in clinical dental technology right after graduation by reinforcing job-based practice education.

• The Korean Journal of Nuclear Medicine
• /
• 제29권4호
• /
• pp.518-525
• /
• 1995

목적 : 안구제거술 후에 삽입한 hydroxyapatite 안구보충물내로 혈관신생이 완전하게 일어 나는 시기를 알아보기 위함이다. 방법 : 안구제거술을 받은 43예의 환자(남자 33예, 여자 10예, 14-56세)에게 대부분 변경되지 않은 방법으로 hydroxyapatite 안구보충물을 삽입한 후 10-23주 사이에 다양한 간격(10-12 주 2예, 13-16주 18예, 17-20주 20예, 21-23주 3예)을 두고 $^{99m}Tc-MDP$ 골주사를 시행하여 보충물내로의 혈관신생 정도를 전향적으로 측정하였다. 정면 및 측면촬영의 정적영상에서 안구보충물의 방사능섭취가 비교(nasal bridge)의 방사능섭취보다 약할 경우를 grade 1, 같을 경을 grade 2, 강할 경우를 grade 3로 나누었으며 grade 2와 3을 혈관신생이 완전하다고 정의하였다. 또한 43예 모두에서 방사능섭취 정도와 관계없이 안구보충물 삽입후 평균 21주되는 시기에 안구보충물에 구멍을 내어 이 구멍으로부터의 출혈여부를 확인한 후 운동성나사(motility peg)를 끼워 의안(prosthesis)과 연결하였다. 43예중 7예에서는 $^{99m}Tc-MDP$ 골주사와 조영제주입후의 자기공명영상(Gd-DTPA T1-weighted images)을 같은 날짜에 시행하여 각각의 예에서 방사능섭취 정도와 조영제증강 정도를 비교하였다. 결과 : 안구보충물내로 완전하게 혈관신생이 일어났던 grade 2와 3의 비율은 안구보충물삽입후 10-12주에서는 0%, 13-16주 33%, 17-20주 50%, 21-23주 67%로써 시간경과에 따라 점차 증가하였다. 골주사소견에 관계없이 안구보충물 삽입후 평균 21주되는 시기에 보충물 앞쪽에 구멍을 내었을 때 43예 모두에서 완전한 혈관신생을 의미하는 출혈을 볼 수 있었다. $^{99m}Tc-MDP$ 골주사와 조영제주입후의 자기공명영상을 둘 다 시행한 7예 각각에서 방사능섭취의 정도와 조영제증강의 정도가 거의 일치하였다. 결론 : 본 예비연구의 결과로써 hydroryapatite 안구보충물 삽입후 21주째에 $^{99m}Tc-MDP$ 골주사를 시행하는 것이 좋을 것으로 생각되며, hydroxyapatite 안구보충물내로의 완전한 혈관신생 여부를 보는 데에는 $^{99m}Tc-MDP$ 골주사가 조영제주입후의 자기공명영상보다 더 경제적이라고 할 수 있겠다.